• 대한전기학회논문지:전력기술부문A
• /
• 제55권6호
• /
• pp.255-258
• /
• 2006

We investigated the operating characteristics of the hybrid-type superconducting fault current limiter (SFCL) according to the inductance of secondary windings. The hybrid type SFCL consists of a transformer that has a primary winding and a secondary winding with serially connected $YBa_2Cu_3O_7$ (YBCO) films. The resistive-type SFCL has difficulty when it comes to raising the capacity of the SFCL due to slight differences of critical current densities between units and structure of the SFCL. The hybrid-type SFCL with closed-loop is able to achieve capacity increase through the electrical isolation and reduction of the inductance of the secondary winding with a superconducting element of the same critical current. On the other hand, the current limiting characteristics were nearly identical in the hybrid-type SFCL with open-loop compared to closed-loop, but quench time was longer than the hybrid-type SFCL with closed-loop. We confirmed that the capacity of the SFCL was increased effectively by the reduced inductance of the secondary winding. In addition, the power burden of the system also could be lowered by reducing the inductance of secondary winding.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.6-12
• /
• 1995

High Tc superconducting YBa$_{2}$Cu$_{3}$$O_{7-x}$ thin films were prepared on various substrates by off-axis rf magnetron sputtering method to examine the substrate effects on the film structure and its R-T characteristics. The SEM analysis showed that the surface morphology of the grown YBa$_{2}$Cu$_{3}$O.sub 7-x/, film has different characteristic structure with different substrate used. The film on (100) SrTiO$_{3}$ substrate has critical current density of 3*10$^{5}$ A/cm$^{2}$ at 77K under zero magnetic field. The X-ray diffraction measurements revealed that the films on (100) SrTiO$_{3}$ substrate have mixed a-axis and c-axis normal to the substrate surface and the films on (100) MgO and ZrO$_{2}$/sapphire substrates have c-axis normal orientation to the substrate surface. However, YBa$_{2}$Cu$_{3}$$O_{7-x}$ films on (100) sapphire substrates showed no preferential orientation.ion.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.272-275
• /
• 2000

We investigated a resistive superconducting fault current limiter (SFCL) fabricated using YBCO thin films on 2-inch diameter sapphire substrates. Nearly identical SFCL units were prepared and tested. The units were connected in series and parallel to increase the current and voltage ratings. A serial connection of the units showed significantly unbalanced power dissipation between the units. This imbalance was removed by introducing a shunt resistor to the firstly quenched unit. Parallel connection of the units increased the current rating. An SFCL module of 4 units in parallel, each of which has minimum quench current 25 Ap, was produced and successfully tested at a 220 V circuit. From the resistance increase, we estimated that the film temperature increases to 200 K in 5 msec, and 300 K in 120 msec. Successive quenches revealed that this system is stable without degradation in the current limiting capability under such thermal shocks as quenches at 220 V.

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.77-82
• /
• 2005

We report a successful fabrication of high-quality $SmBa_{2}Cu_{3}O_{7-{\delta}}$ (SmBCO) thin films on $LaAlO_3$(LAO)(100) single crystalline substrates by a modified TFA-MOD method. After the pyrolysis heat treatment of spin-coated films up to $400^{\circ}C$, SmBCO films were fired at various temperatures ranging from 810 to $850^{\circ}C$ in a reduced oxygen atmosphere (10 ppm $O_2$ in Ar). Optimally processed SmBCO films exhibited the zero-resistance temperature ($T_{c,zero}$) of 90.2 K and the critical current density ($J_c$) of $0.8\;MA/cm^2$ at 77K in self-field. Compared with the $J_c$ values (normally, > $2\;MA/cm^2$ at 77 K) of MOD-TFA processed YBCO films, rather depressed $J_c$ values in SmBCO films are most probably attributed to the existence of ${\alpha}$-axis oriented grains.

• Progress in Superconductivity
• /
• 제5권2호
• /
• pp.94-97
• /
• 2004

Step-edge Josephson junctions (SEJ) have been fabricated on sapphire substrates with in situ deposited films of CeO$_2$ buffer layer and YBa$_2$Cu$_3$O$_{7}$ films on the low angle steps. Direct coupled SQUID magnetometers with the SEJ were formed on 1 cm X 1 cm R-plane sapphire substrates. Typical 5-${\mu}{\textrm}{m}$-wide Josephson junctions have R$_{N}$ of 3 Ω and I$_{c}$ of 50 $mutextrm{A}$ at 77 K. The direct coupled SQUID magnetometers were designed to have pickup coils of 50-${\mu}{\textrm}{m}$-wide 16 parallel loops on the 1 cm X 1 cm substrates with outer dimension of 8.8 mm X 8.8 mm. The SEJ SQUID magnetometers exhibit relatively low 1/f noise even with dc bias control, and could be stably controlled by flux-locked loops in the magnetically disturbed environment. Field noise of the do SQUID was measured to be 200∼300 fT/Hz$^{1}$2/in the white noise region and about 2 pT/Hz$^{1}$2/ at 1 Hz when measured with dc bias method.hod.d.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권4호
• /
• pp.13-16
• /
• 2004

Three film deposition systems (pulsed laser deposition, sputtering, and evaporation) equipped with reel-to-reel metal tape moving apparatus were installed and used to make meter-long coated conductor. Buffer architecture of $CeO_2/YSZ/Y_2O_3$ was deposited on Ni alloy using sputtering, evaporation, and PLD. YBCO superconducting layer was continuously deposited on buffered metal tape by PLD. End-to-end critical current ($I_c$) of 107 A at 77 K, self-field has been achieved in 1 em-wide tape (thickness 0.6∼1.0${\mu}{\textrm}{m}$, tape moving speed 54∼72 cm/hr) over 1 meter length.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권4호
• /
• pp.25-29
• /
• 2015

In 1987, M. K. Wu and Paul Chu discovered $Y_{1.2}Ba_{0.8}CuO_4$ (YBCO) with critical temperature ($T_c$) of 93 K. It has significantly lowered the cost of cooling of a material up to the point where superconductivity set in. Utilizing the cost reduction of attaining superconductivity and the vast amount of research to understand characteristics of high temperature oxide superconducting materials, there has been effort to use a high temperature superconductor as a coated conductor. It is important to characterize the materials precisely for stable performance before commercializing. We used polarized Raman scattering spectroscopy to study structural and stoichiometric information regarding $YBa_2Cu_3O_{7-x}$, $GdYBa_2Cu_3O_{7-x}$, and $GdBa_2Cu_3O_{7-x}$ produced by three leading groups of producing commercial grade high temperature superconductor coated conductors American Superconductor Corporation, Superpower, and SuNAM.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권2호
• /
• pp.24-28
• /
• 2013

In this study, the homogeneity of critical current, $I_c$, along the lengthwise direction in the coated conductor (CC) tape under uniaxial tension was investigated using a multiple voltage tap configuration. Initially, a gradual and homogeneous $I_c$ degradation occurred in all subsections of the tape up to a certain strain value. This was followed by an abrupt $I_c$ degradation in some subsections, which caused scattering in $I_c$ values along the length with increasing tension strain. The $I_c$ degradation behaviour was also explained through n-value as well as microstructure analyses. Subsections showed $I_c$ scattering corresponding to damaged areas of the CC tape revealed that transverse cracks were distributed throughout the gauge length. This homogeneous $I_c$ degradation behaviour under tension is similar with the case under torsion strain but different with the case under hard bending which were previously reported. This behaviour is also different with the case using Bi-2223 HTS tapes under tension strain.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.5-10
• /
• 2018

This study presents that various grain boundary junctions are prepared by controlling the seed orientation combined with an artificial hole in a melt process REBCO bulk superconductor. Large grain YBCO superconductors have been fabricated with various grain boundary junctions that the angle between the grain boundary and the <001> axis of Y123 crystal is $0^{\circ}$, $30^{\circ}$ and $45^{\circ}$, respectively. The presence of the artificial hole is beneficial for the formation of clean grain boundary junction and single peak trapped magnetic field profiles have been obtained. Artificial hole makes two growth fronts meet at a point on a periphery of the artificial hole. The presence of artificial hole is not likely to affect on the distribution of Y211 particles. The newly formed <110> facet lines are explained by the formation of new Y123/liquid interface with (010) crystallographic plane.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.707-708
• /
• 2008

본 논문에서는 초전도 플라이휠 에너지 저장장치 (Superconductor Flywheel Energy Storage System : SFES)의 에너지 변환을 위해 사용된 영구 자석형 전동 발전기(Permanent Magnet Synchronous Motor/Generator : PMSM/G)가 SFES의 에너지 저장효율에 미치는 영향을 평가하였다. SFES 시스템은 YBCO 벌크 초전도체를 이용한 저어널 타입(journal type)의 초전도 베어링을 사용하였으며, 슬롯리스 형 PMSM/G를 사용하였다. PMSM/G의 고정자 코어, 누설 자속 및 감겨진 코일에 의한 저장 에너지 손실을 측정하였다. 사용된 코어의 크기, 누설자속, 및 코일의 적절한 선정을 통하여 저장된 에너지의 손실을 상당히 줄일 수 있음을 확인하였다. 또한 영구자석과 코어가 동시에 회전하는 회전 코어형 전동발전기를 적용하여 에너지 손실을 매우 감소시킬 수 있음을 확인하였다.