• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.932-934
• /
• 2002

In this paper, we proposed a method to shield perpendicular magnetic fields in high Tc superconductor(HTS) tape of a shell-type HTS transformer with double pancake windings. A diamagnetism of characteristics of superconductor is used to shield magnetic field. For a shielding experiment, a proper shielding model is chosen, and several kinds of HTS are used such as a monofilament HTS tape, two kinds of multifilament HTS tapes and YBCO film disk. The effect of shielding for the perpendicular magnetic field is measured with HTSs for shielding and their utility for shielding is proved.

• ETRI Journal
• /
• v.19 no.2
• /
• pp.48-58
• /
• 1997

Using high quality high-$T_c$ superconducting (HTS) YBCO thin films, we designed and fabricated 3-pole, 5-pole, and 7-pole lowpass filters consisting of microstrip transmission lines and open-stub lines. We measured the microwave response of the filters in the temperature range of T=85 K to 27 K. AtT=30 K, the observed inband insertion loss was 0.14dB and 0.02dB for the 5-pole and 7-pole filters, respectively. The cut-off frequency was 4.7 GHz for the 5-pole filter and 7.9GHz for the 7-pole filter. To the authors' knowledge, the measured inband insertion losses are the best values reported so far for the open-stub line type HTS multipole lowpass filters. The skirt property of the 5-pole filter showed a large improvement over that of the 3-pole filter as predicted from the simulation. We found that, to obtain a stable performance, the HTS multipole lowpass filters should be operated at the temperatures between 60% and 70% of $T_c$.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.127-130
• /
• 2002

Step-edge dc SQUID magnetometers have been fabricated on sapphire substrate. Ce$O_{2}$ buffer layer and $YBa_{2}$$Cu_{3}$ $O_{7}$(YBCO) films were deposited in-situ on the low angle (~$35^{\circ}$)steps formed on the substrates. Typical 5-$\mu$m-wide junction has $R_{N}$ of 4 $\Omega$ and $I_{c}$ of 60 $\mu$A with $I_{c}$$R_{N}$ product of 240 $\mu$V at 77 K. According to applied bias current, depth of voltage modulation was changed and maximum voltage was measured 100~300 fT/$\checkmark$ Hz at 100 Hz, and about 1.5 pT/$\checkmark$ Hz at 1 Hz. For ac bias reversal method, field noise was decreased in the 1/f region. The QRS peak of magneto-cardiogram was measured 50 pT in the magnetically shielded room.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.159-162
• /
• 2002

The eleventh-order coupled line lowpass filter(LPF) was designed to suppress harmonics and spurious signals. The microstrip type LPF was fabricated using a high-$T_{c}$ superconductor(HTS) $YBa_{2}$$Cu_{3}$$O_{7-x}$(YBCO) thin film with the $CeO_{2}$ buffer layer which was deposited on the sapphire ($Al_{2}O_{3}$) substrate of 30 x 30 $mm^{2}$. The coupled-line type LPF was designed for 1.2 GHz of cutoff frequency with 0.01 dB of ripple level at passband. The fabricated HTS LPF shows excellent attenuation characteristics in stopband of 1.2~9.5GHz (7-attenuation poles in the stopband), and shows low insertion loss (0.2 dB) and return loss (17.1 dB) in the pass- band. These measured results match well with those obtained by the EM simulation. This clearly demonstrates that the HTS LPF can suppress harmonics and spurious signals effectively.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.119-122
• /
• 2002

The NiO buffer layers for YBCO coated conductor were prepared on textured Ni substrates by MOCVD method and the degree of texturizing and the surface roughness were analyzed X-ray pole figure and AFM and SEM. Processing variables were oxygen partial pressure and substrate temperature. (200) textured NiO layer was formed at 450~$470^{\circ}C$ and oxygen partial pressure of 1.67 Torr. Out-of-plane($\omega$-scan) and in-plane($\Phi$-scan) texture were $10.34^{\circ}$ and $10.00^{\circ}$ respectively. The surface roughness estimated by atomic force microscopy was in the range of 3.1~4.6 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.812-815
• /
• 2007

To apply the superconducting fault current limiter(SFCL) into a power system, the analysis for its recovery characteristics as well as the consideration for its cooperation with other protecting machine such as a circuit breaker is required. The recovery characteristics of the flux-lock type SFCL like its current limiting characteristics are dependent on the winding direction of two coils. In this paper, the experiments of the current limiting and the recovery characteristics of the flux-lock type SFCL with YBCO thin film were performed. From the analysis on the experimental results due to the winding direction of two coils, the limited fault current in case of the additive polarity winding was observed to be lower than that for the case of the subtractive polarity winding. In addition, the recovery time was found to be faster in case of the additive polarity winding compared to the subtractive polarity winding.

• 한국초전도학회:학술대회논문집
• /
• v.16
• /
• pp.68-68
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.894-895
• /
• 2011

본 논문은 5 MJ의 저장용량을 가지는 초전도 에너지 저장장치용(Superconducting Magnetic Energy Storage System, SMES) 마그넷의 설계에 관한 연구 결과이다. 마그넷의 설계에 사용된 초전도 선재는 2세대 고온초전도 선재인 YBCO CC이고, 초전도 선재의 냉각방식은 냉동기를 이용한 전도냉각으로 마그넷의 운전온도는 14 K 이다. SMES용 마그넷은 테이프형태를 가지고 있는 초전도 선재의 형태를 고려하여 팬케이크 코일로 권선된 모듈코일을 이용하여 토로이드 형태의 마그넷 구조로 설계되었다. 설계를 통해 마그넷의 저장에너지와 초전도 선재의 사용량, 자속밀도 분포 등을 확인하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.116-119
• /
• 2010

In this work, we presented the characterization of 3 dB branch type directional couplers by using High-Tc superconducting thin films. To do this, we deposited YBCO superconducting thin films on MgO substrates by using rf-magnetron sputtering techniques. The designed center frequency was 408 MHz and the designed passband was 20 MHz. Also we designed 3 dB Power difference and $90^{\circ}$ of phase difference between port 3 and port 4. The even and odd mode analysis were used to characterize our directional couplers and em Sonnet (full wave analysis program) was utilized to the optimum design. We reported experimental results, including a center frequency, passband, half power characteristics and phase differences. We confirmed that experimental results were in good agreements with characterization by using full wave analysis program.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.112-115
• /
• 2000

In this work the results of the systematic investigations on the effect of organic addition by using polymer compound as starting materials on the superconducting properties of YBCO electrophoretic deposited films on silver substrate are presented. The characteristics of the films were examined by X-ray diffraction and SEM observation. Our results show that the adhesion and microstructure of these films are sensitive to the nature of polymer compounds and sintering conditions (electrophoretic deposition, drying and heat-treatment procedures). To develop optimum microstructures for samples processed in this manner it is necessary to have an understanding of how these processes affect the microstructure and hence the properties of ceramic superconductors.