• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.72-78
• /
• 2007

Aluminized steel sheet is a material with excellent heat resistance, thermal reflection and corrosion resistance. It has wide applications, owing to its low cost and excellent performance, in the petrochemical industry, electric power and other energy conversion systems, etc and has attracted the attention of many investigators. But the welding of aluminized steel sheet has a problem of decreasing tensile-shear strength, caused by mixed Al in the weld. This study investigated behavior of Al and its structural properties to resolve this problem. Several analysis equipment(SEM, EDX, EPMA) were used to investigate Al element in the weld. Also microhardness tester and TEM equipment were used to find the intermetallic compound. As a result of this study, Al-rich zones existed in the weld and Fe-Al intermetallic compounds were found in these zones. At the same time, the weldability of aluminized stainless steel sheet was investigated and compared with that of aluminized steel sheet. Although there is a difference between the base metal of the low carbon steel and stainless steel, it is interpreted that a behavior of Al element in the weld is similar.

• Journal of Oral Medicine and Pain
• /
• 제22권1호
• /
• pp.125-135
• /
• 1997

The Author examined the clinical and histological changes on the dorsal tongue mucosa of the adult rats after lasing by pulsed Nd:YAG laser and incising with scalpel. The dorsal tongue was lased through 320$\mu\textrm{m}$optic fiber moving 2.5mm/second to make linear incision 5mm. The five conditions of lasing were three application with 1.0W, 1.75W, 3.0W and 3.0W under saline cooling, and single application with 3.0W at 20Hz. With scalpel, linear incisions through the surface epithelium were performed to 5mm in length. After observing the clinical changes of the incised wounds, the animals were sacrified and the tissues were excised to make the tissue specimens. The stained microscopic tissue slide were observed histologically under the microscope. The following results were obtained : 1. While incision with scalpel causes severe bleeding, lasing does not cause bleeding. 2. In three applications with 1.75W and 20Hz, tissue ablation was limited to areas contacted with optic fiber. 3. In three applications with 3.0W and 20Hz, deep incised wound, extensive destruction of the adjacent epithelium and charring were observed. 4. In three applications with 3.0W and 20Hz under saline cooling, tissue ablation was limite to the superficial mucosa and charring was not observed. 5. In single application with 3.0W and 20Hz, the shape of the incised wound was similar to that of the scalpel incision.

• 한국군사과학기술학회지
• /
• 제14권5호
• /
• pp.897-903
• /
• 2011

The objective of this study is to investigate the thermal behavior on material surface and the variation in the surface morphology of aluminum 6061 alloy by the Nd:YAG pulsed-laser irradiation. First, we predicted the surface temperature variation during pulsed-laser irradiation by using the two dimensional finite element analysis. When the pulsed-laser of 133 mJ energy and 5 ns pulse duration is irradiated on the surface of aluminum alloy, the material surface is thought to be melting because the surface temperature rises steadily up to about $660^{\circ}C$ exceeding the melting point. Also, the experimental results show that the solidification microstructure has been developed clearly after surface melting. Second, the diameter of melted zone was analysed by finite element analysis and measured by OM(Optical Microscopy). It increased logarithmically with increase in the number of laser irradiation. In addition, AFM(Atomic Force Microscopy) measurement showed an increase in the average surface roughness during pulsed-laser irradiation.

• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.35-41
• /
• 2016

The experimental study has been performed through residual stress using the Ti6Al4V, investigate the effect of laser shock peening on laser welding process residual stress of Ti6Al4V welds in a reduce safety weld zone. This research evaluated the effects of shock waves from laser shock peening with a pulsed Nd:YAG laser on Ti6Al4V welding specimens, through the analysis of the residual stress of the specimens. The residual stress could be formed by the depth of 1 mm if the proposed method of reducing the residual stress is performed in the optimal condition. The welded structures and products during the production process increase the mechanical property of repeated stress, which could be expected to extend the fatigue life of the structure.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.539-544
• /
• 2012

Thermal shock behavior of TiN-coated SUS 304 substrate was investigated using a laser ablation method. By short surface ablation with a pulse Nd-YAG laser, considerable surface crack and spalling were observed, whereas there were few oxidation phenomena, such as grain growth of TiN crystallites, nucleation and growth of $TiO_2$ crystallites, which were observed from the coatings quenched from $700^{\circ}C$ in a chamber. The oxygen concentration of the ablated coating surface with the pulse laser also had a lower value than that of the quenched coating surface by Auger electron spectroscopy and electron probe micro analysis. These results were attributed to the fact that the properties of the pulse laser method have a very short heating time and so the diffusion time for oxidation was insufficient. Consequently, it was verified that the laser thermal shock test provides a way to evaluate the influence of the thermal shock load reduced oxidation effect.

• 한국산업융합학회 논문집
• /
• 제22권4호
• /
• pp.447-457
• /
• 2019

The intelligent sensory system is required to ensure the accurate welding performance. This paper describes the development of an intelligent vision sensor for the robotic laser welding. The sensor system includes a PC based vision camera and a stripe-type laser diode. A set of robust image processing algorithms are implemented. The laser-stripe sensor can measure the profile of the welding object and obtain the seam line. Moreover, the working distance of the sensor can be changed and other configuration is adjusted accordingly. The robot, the seam tracking system, and CW Nd:YAG laser are used for the laser welding robot system. The simple and efficient control scheme of the whole system is also presented. The profile measurement and the seam tracking experiments were carried out to validate the operation of the system.

• Nuclear Engineering and Technology
• /
• 제55권11호
• /
• pp.4159-4166
• /
• 2023

Laser decontamination of radioactive surfaces is an innovative technology. Our contribution to improving this technology includes studies on laser beam decontamination with a pulsed laser of an average power of 150 W, equipped with a hand guided working head. Our investigations are focused on metallic surfaces typical in nuclear power plants, such as stainless steel, bright and rusted mild steel, galvanized steel, and painted steel. As typical nuclides of contaminated surfaces we chose Co-60 and Cs-137, the most frequently occurring nuclides in many nuclear plant components; Sr-85 as a representative of Sr-90, the potentially most harmful fission nuclide; and Am-241 as a representative of the minor alpha-radiation emitting actinides. Here, we present our results of decontamination and recovery ratios. Decontamination ratios of 90-100% were achieved on different surfaces.

• 한국광학회지
• /
• 제21권3호
• /
• pp.123-128
• /
• 2010

이터븀 광격자 시계의 검색 레이저로 쓰기 위하여, WG-PPLN를 사용하여 1319 nm 파장의 Nd:YAG 레이저와 1030 nm 파장의 Yb 도핑된 광섬유 레이저의 합주파수 (578.4 nm)를 발생시켰다. 이터븀 광격자에서 시계 전이선을 분광하기 위해서는 1 Hz 수준의 선폭을 가지는 검색 레이저가 필요하기 때문에, 합주파수로 발생된 노란색 레이저의 주파수를 초공진기에 안정화하여 선폭을 축소하였다. 초공진기는 선팽창 계수가 낮은 ULE로 제작되었고, 진동으로 인한 영향이 작은 받침점에서 능동형 제진대 위에 설치되었다. 공기 굴절률의 영향을 제거하기 위하여 이 초공진기를 진공 체임버 내부에 설치하고, 온도를 1 mK 수준에서 안정화 하였다. 또한, 이 장치들을 방음 체임버 안에 설치하여, 소리로 인한 잡음을 막아 주었다. 실험에 사용된 초공진기의 광자 수명시간으로부터, 그 예리도가 380 000으로 측정되었다.

• Restorative Dentistry and Endodontics
• /
• 제27권6호
• /
• pp.555-560
• /
• 2002

치근부 민감성 (hypersensitivity)은 부분적으로 치근면에서의 개방된 상아세관이 존재하는 것에 기인한다고 생각되며 이러한 치근부의 개방된 상아세관은 치경부 병소 (cervical lesion)에 주로 존재하는데 이는 칫솔질에 의한 마모(toothbrush abrasion), 화학적 침식 (chemical erosion), 또는 abfraction 등의 결과로 나타난다고 한다. 이미 Nd-YAG 레이저를 이용한 실험에서 레이저를 조사한 상아질 표면의 상아 세관 구경이 감소되고 상아세관의 폐쇄가 많이 증가되는 양상을 관찰한 바 있다. 이 실험의 목적은 고출력레이저인 Nd-YAC 레이저를 이용한 상아질 표면처치의 임상사용가능성을 좀 더 상세히 평가하기 위해 상아질에 레이저를 처리한 후 기계적으로 마모시킨 경우 상아질 표면의 변화를 관찰하는 것이다. 50개의 발치된 치아의 상아질을 노출시켜 표면을 연마한 후 대조군에서는 37% 인산으로 산부식하여 상아 세관을 노출시킨 후 레이저를 조사하였고, 실험군에서는 대조군과 같은 조건으로 산과 레이저로 처리된 상아질 표면을 15, 45, 90 그리고 180분 동안 전동 칫솔로 기계적으로 마모시켜 그 표면을 주사전자현미경으로 관찰한 결과, 대조군, 칫솔질을 15, 45분간 시행한 실험군에서는 상아 세관 입구가 10% 이내에서 노출되었고 50 그리고 180분간 칫솔질을 시행한 실험군에서는 45 그리고 48%의 상아세관 입구의 노출이 관찰되었다. 그러므로 Nd-YAC레이저의 조사는 상아질 표면에서 축적 시간이 45분 이상에서 90분 이하인 기계적 마모에 의한 상아 세관 입구의 노출을 억제할 수 있을 것이라 사료된다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 추계학술대회 논문집
• /
• pp.292-300
• /
• 2001

The paper describes spectroscopic characteristics of plasma induces in the pulsed YAG laser welding of alloys containing a large amount of volatile elements. The authors have conducted the spectroscopic analyses of laser induced Al-Mg alloys plasma in the air and argon atmosphere. In the air environment, the identified spectra were atomic lines of Al, Mg, Cr, Mn, Cu, Fe and Zn, and singly ionized Mg lines, as well as the intense molecular spectra of A10 and Mg0 formed by chemical reactions of evaporated Al and Mg atoms from the pool surface with oxygen in the air. In argon atmosphere, Mg0 and AI0 spectra vanished, but AIH spectrum was detected. The hydrogen source was presumably hydrogen dissolved in the base metals, water absorbed on the surface oxide layer, or $H_2$ and $H_2O$ in the shielding gas. The resonant 1ines of Al and Mg were strongly self-absorbed, in particular, self-absorption of the Mg 1ine was predominant. These results show that the laser induced plasma was made of metal1ic vapor with relatively low temperature and high density.