• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.75-79
• /
• 2013

A power distribution network (PDN) is a network that provides connection between the voltage source supply and the power/ground terminals of a microprocessor chip. It consists of a voltage regulator module, a printed circuit board, a package substrate, a microprocessor chip as well as decoupling capacitors. For power integrity analysis, the board and package layouts have to be transformed into an electrical network of resistor, inductor and capacitor components which may be expressed using the S-parameters models. This modeling process generally takes from several hours up to a few days for a complete board or package layout. When the board and package layouts change, they need to be re-extracted and the S-parameters models also need to be re-generated for power integrity assessment. This not only consumes a lot of resources such as time and manpower, the task of PDN modeling is also tedious and mundane. In this paper, a block-based PDN modeling is proposed. Here, the board or package layout is partitioned into sub-blocks and each of them is modeled independently. In the event of a change in power rails routing, only the affected sub-blocks will be reextracted and re-modeled. Simulation results show that the proposed block-based PDN modeling not only can save at least 75% of processing time but it can, at the same time, keep the modeling accuracy on par with the traditional PDN modeling methodology.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.93-100
• /
• 1998

Pyoelectric infrared detectors based on La-modified PbTiO3 (PLT) thin films have been fabricated by RF magnetron sputtering and micromachining technology. The detectors form Pb$_{1-x}$ La$_{x}$Ti$_{1-x}$ O$_{3}$ (x=0.05) thin film ferroelectric capacitors epitaxially grown by RF magnetron sputtering on Pt/MgO (100) substrate. The sputtered PLT thin film exhibits highly c-axis oriented crystal struture that no poling trealization for sensing applications is required. This is an essential factor to increase the yield for realization of an infrared image sensor. Micromachining technology is used to lower the thermal mass of the detector by giving maximum sensor efficiency. Polyimide is coated on top of the sensing elements to support the fragile structure and the backside of the MgO substrate is selectively eteched to reduce the heat loss. The sensing element exhibited a very high detectivity D* of 8.5*10$^{8}$ cm..root.Hz/W at room temperature and it is about 100 times higher than the case of micromachining technology is not used. a sensing system that detects the position as well as the existence of a human body is realized using the array sensor.sor.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.98-104
• /
• 2006

The conventional burst-mode APC(Automatic Power Control) circuit had an effective structure that was suitable for a low power consumption and a monolithic chip. However, as data rate was increased, it caused errors due to the effect of the zero density. In this paper, we invented a new structured peak-comparator which could compensate the unbalance of the injected currents using double gated MOS and MOS diode. And we proposed a new burst-mode APC adopting it. The new peak-comparator in the proposed APC was very robust to zero density variations maintaining the correct decision point of the current comparison at high data rate. It was also suitable for a low power consumption and a monolithic chip due to lack of large capacitors.

• Journal of the Korean Electrochemical Society
• /
• v.20 no.1
• /
• pp.13-17
• /
• 2017

In this study, we studied the organic electrolyte application to electrochemical capacitor for high operation voltage. For high operating voltage, 5 wt % of gamma butyroloctone (GBL) was added in the bare electrolyte. During the cycle performance, stable SEI layers were formed by reductive decomposition of additive GBL. As a result, columbic efficient of 1M $SBPBF_4$ in EC:DMC(1:1) with GBL composite was enhanced to 70% after the 2000th cycle at voltage range 0-3.5 V. Additionally, SEI layer protected the surface of electrode and prevent the side-reaction between electrolyte to electrode.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.2
• /
• pp.93-98
• /
• 2018

$MnO_2$, a metal oxide used as an electrode material in electrochemical capacitors (EDLCs), has been applied in binary oxide and conducting polymer hybrid electrodes to increase their stability and capacitance. We developed a method for electrodepositing Mn-Ni oxide/PANI, Mn-Ni oxide/PEDOT, and Mn-Ni-Ru oxide/PEDOT films on carbon paper in a single step using a mixed bath. Mn-Ni oxide/PEDOT and Mn-Ni-Ru oxide/PEDOT electrodes used in an electro-osmotic pump (EOP) have shown better efficiency compared to Mn-Ni oxide and Mn-Ni oxide/PANI electrodes through testing in water as a pumping solution. EOP using a Mn-Ni-Ru oxide/PEDOT electrode was also tested in a 0.5 mM $Li_2SO_4$ solution as a pumping solution to confirm the effect of the $Li^+$ insertion/de-insertion reaction of Ruthenium oxide on the EOP. Experimental results show that the flow rate increases with the increase in current in a 0.5 mM $Li_2SO_4$ solution compared to that obtained when water was used as a pumping solution.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.365-366
• /
• 2002

A novel TEM resonator coil was developed for the imaging of small animals. The functional elements of the TEM resonator were 8 inner conductors, distributed in a cylindrical pattern and connected at the ends with capacitors to the cylindrical outer shield. The TEM resonator coil with cavity elements was robust to the surrounding influences due to the self-shielding structure. The TEM resonator coil with high Q factor could provide high quality MR images at 3.0T MRI system. Also, the TEM resonator coil has an advantage for a fine tune with length adjustment of each cavity elements. Thus, The TEM resonator coil at 3.0T, even higher field could be used in the research studies.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1131-1134
• /
• 2003

Unknown parameters of a nonlinear system were estimated using a signal compression method. The estimated parameters were natural frequency and tile damping coefficient. This study applied a algorithm using tile comparison of the cross-correlation coefficient between the impulse response from a model and it from the signal compression method. The impulse through linear element included in a nonlinear system could be obtained by the signal compression method. The unknown parameters of the linear element could be estimated by comparing the Bode plots of system's impulse response with them of model's response. In this study, a LSCM(LabVIEW-Signal-Compression-Method) was developed to identify a nonlinear system. The LSCM consisted of National Instrument's (NI) Data Acquisition (DAQ) Board (Model PCI-1200), a monitoring program using LabVIEW software package, DAQ Signal Accessory Board, and 2nd-order electric circuits. The designed electric circuits consisted of resistors, inductors and capacitors. To evaluate the performance of the LSCM, the response from model with known parameters is compared with the response from the real system using the monitoring program. The results from simulation of experiment showed that the developed LSCM provided a reliable estimation performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.5
• /
• pp.455-461
• /
• 2015

This paper deals with an experimental verification of a temperature-dependent power loss model of a DC/DC converter in severe temperature conditions. The power loss of a DC/DC converter is obtained by summing the losses by the components constituting the converter including switching elements, diodes, inductors, and capacitors. MIL-STD-810F stipulates that any electronic devices must be operable in the temperature ranging from $-50^{\circ}C$ to $70^{\circ}C$. We summarized the temperature-dependent loss models for the converter components. A SEPIC-type converter is designed and built as a target. Using a constant-temperature chamber, a test rig is set up to measure the power loss of the converter. The experimental results confirm the validity of the loss model within 4.5% error. The model can be useful to predict the efficiency of the converter at the operating temperature, and to provide guidelines in order to improve the efficiency.

• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.272-278
• /
• 2017

Two-dimensional (2D) materials, especially graphene and $MoS_2$ sheets, have gained much attention and shown great promise for the application in supercapacitors. To widely use the 2D materials for supercapacitors, highly efficient, low cost, and environmentally friendly synthetic methods for the preparation of 2D materials should be developed. Here, we will review recently developed solution-based processes for preparing 2D materials for supercapacitors. Chemical exfoliation-reduction, chemical intercalation, and liquid phase exfoliation methods will be introduced. Moreover, the electrochemical characteristics of graphene and $MoS_2$-based electrodes for supercapacitors are summarized. In addition to solution-based processes, other challenges and opportunities are discussed in terms of controlling nanosheet compositions, sizes, and thicknesses.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.596-600
• /
• 1986

This paper describes a capacitively reading apparatus for determining the angular orientation, speed and/or direction of rotary objects such as shaft, dial hand, counter wheel and the like. The apparatus consists of sensing device and circuit accompanying with said sensing device. The sensing device is provided by arranging many stationary electrodes lying substantially on a surface of a stationary plane member and by arranging rotary electrode lying substantially on a surface of rotary objects to be monitored, in which said rotary electrode is in confronting relationship to some stationary electrodes so as to construct unique capacitors according to the angular position of rotary objects. The angular position of said rotary electrode is determined by sets of stationary electrodes which are in confronting relationship to rotary electrode. A carrier signal is generated by scanning device while scanning said stationarelectrodes, whose periods are in corresponding relationship to said stationary electrodes, respectively. The periods of carrier corresponding to the angular position of said rotary electrode is modulated by a modulation signal generated by detecting device according to said rotary electrode. This apparatus is applied to automatically monitor any kind of storage tank, as well as to automatically read the conventional utility meters such as Watthour meters, Gas meters, Water meters, etc..