• Clean Technology
• /
• v.24 no.1
• /
• pp.77-84
• /
• 2018

In this study, $Li_4Ti_5O_{12}$ anode materials for lithium ion battery were synthesized by dry ball-mill method. Polyvinyl chloride (PVC) as a carbon source was added to improve electrochemical properties. When the PVC was added after $Li_4Ti_5O_{12}$ formation, the spinel structure was well synthesized and it was confirmed by X-ray diffraction (XRD) experiments. When the carbon material was added before the synthesis and the heat treatment was performed, it was confirmed that a material having a different crystal structure was synthesized even when a small amount of carbon material was added. In the case of $Li_4Ti_5O_{12}$ without the carbon material, the electrical conductivity value was about $10{\mu}S\;m^{-1}$, which was very small and similar to that of the nonconductor. As the carbon was added, the electrical conductivity was greatly improved and increased up to 10,000 times. Electrochemical impedance spectroscopy (EIS) analysis showed that the size of semicircle corresponding to the resistance decreased with the carbon addition. This indicates that the resistance inside the electrode is reduced. According to the Cyclic voltammetry (CV) analysis, the potential difference between the oxidation peak and the reduction peak was reduced with carbon addition. This means that the rate of lithium ion insertion and deinsertion was increased. $Li_4Ti_5O_{12}$ with 9.5 wt% PVC added sample showed the best properties in rate capabilities of $180mA\;h\;g^{-1}$ at 0.2 C-rate, $165mA\;h\;g^{-1}$ at 0.5 C-rate, and $95.8mA\;h\;g^{-1}$ at 5 C-rate.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.11
• /
• pp.812-820
• /
• 2011

This study was conducted to characterize $CO_2$ biomineralization on several minerals (i.e., CaO, MgO, $SiO_2$) by bottle test in an aqueous solution and solidified sludge using different aerobic bacterial strains like Bacillus megaterium and Bacillus pasteurii by batch test. These bacteria promote the formation of microenvironments that facilitate the precipitation of mineral phases that were unsaturated in the bulk solution. For one type of mineral solely amended, the $CO_2$ was reduced at the highest of 4.0 mmol for MgO while it was not that much lower for CaO and $SiO_2$ showing 1.1 and 0.3 mmol $CO_2$2, respectively. For two types of minerals simultaneously amended, the $CO_2$ was reduced at the greater extent for both Ca + Mg and Mg + Si showing 2.7 and 2.3 mmol, respectively whereas it was less for Ca + Si at 1.8 mmol. For solidified sludge, the $CO_2$ reduction rate changed depending on the volume of solidified sludge placed in the medium and the input $CO_2$ concentration.. The reduction rate of $CO_2$ was increased with increasing the volume of solidified sludge. Results of XRD analysis indicate that $CaCO_3$ (Calcite) was dominantly formed among others (e.g., Aragonite, Dolomite). SEM analysis showed that the sample with Bacillus pasteurii, could more form minerals rather than control. As demonstrated in this study, $CO_2$ would be effectively sequestered in biomineralization process.

• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.3-12
• /
• 2006

The feasibility for the employment of manganese nodule as an adsorbent for $SO_{2}$ gas has been investigated. The specific surface area of manganese nodule particle, which used in the experiments, was ca. $221.5m^{2}/g$ and the content of sulfur in manganese nodule was observed to significantly increase after $SO_{2}$ was adsorbed on it. The EPMA for the distilled water-washed and methanol-washed manganese nodule particle after $SO_{2}$ adsorption showed that its sulfur content was slightly decreased to 14.7% and 13.1% respectively, from 15.4% before washing. The XRD analysis of manganese nodule showed that todorokite and birnessite, which are manganese oxides, and quartz and anorthite were the major mineralogical components and weak $MnSO_{4}$ peaks were detected after $SO_{2}$ was adsorbed on manganese nodule. For an comparative investigation, limestone was also tested as an adsorbent for $SO_{2}$, however, no peaks for $CaSO_{4}$ were found by XRD analysis after the adsorption of $SO_{2}$. As the size of adsorbent increased, time for breakthrough was decreased and the adsorbed amount of $SO_{2}$ was also diminished. The $SO_{2}$ adsorption was hindered when its flow rate became high and the adsorption capacity of manganese nodule was observed to be superior to that of limestone. In addition, the mixture of manganese nodule and limestone did not show an increase in the adsorption of $SO_{2}$. Finally, as the temperature was raised, the adsorbed amount of adsorbate on manganese nodule was found to be decreased.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.112-131
• /
• 2011

This article reports the results of scientific analysis using SEM-EDX, XRD, TG/DTA, performed on 5 green glaze samples of the brick and roofing tile excavated from the Sacheonwang temple site in Gyeongju in order to verify the chemical compositions and melting temperature. The glaze samples on 2 clay statues have similar chemical composition (PbO 74~81%, $SiO_2$ 14~18%) and melting temperature range ($970{\sim}1070^{\circ}C$), whereas the 2 tiles of goblin's face and 1 rhomb brick have different characteristics. Sample SC 003 (made of PbO 63~67%, $SiO_2$ 25~28%), one of the tiles of goblin's face, shows low melting temperature range (below $970^{\circ}C$), and sample SC 004 (composed of PbO 64~70%, $SiO_2$ 19~25% and melting point $970{\sim}1070^{\circ}C$), the other tile of goblin's face, shows different chemical characteristics compared with 2 clay statues. The green glaze on rhomb brick shows different composition compared with all the others from Sacheonwang temple site in that it does not show any impurity elements other than the main components (PbO 87~88%, $SiO_2$ 12~13%) with very low melting temperature range ($750{\sim}770^{\circ}C$). Surprizingly, the chemical and optical characteristics of this green-glaze on rhomb brick are very similar to that on the bricks from Yeongmyo temple site, Gyeongju. The above results indicate that raw material and manufacturing method are not same for 5 green-glaze samples from Sacheonwang temple site and therefore suggests that further study on the provenance of raw material such as lead isotope analysis is necessary. Our work will provide basic data for future reproduction study of green glazed brick of Sacheonwang temple site, Gyeongju and will also serve as a reference data for the study of raw material and manufacturing method of green glaze from other sites of cultural assets.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.117-123
• /
• 2021

In this study, the composite was prepared by mixing SiOx, soft carbon, and carbon black and the electrochemical properties of lithium ion battery were investigated. The content of SiOx added to improve the capacity of the soft carbon anode material was varied to 0, 6, 8, 10, 20 wt%, and carbon black was added as a structural stabilizer for reducing the volume expansion of SiOx. The physical properties of prepared CB/SiOx/C composite were investigated through XRD, SEM, EDS and powder resistance analysis. In addition, the electrochemical properties of prepared composite were observed through the charge/discharge capacity, rate and impedance analysis of the lithium ion battery. The prepared CB/SiOx/C composite had an inner cavity capable of mitigating the volume expansion of SiOx by adding carbon black. The formed internal cavity showed a low initial efficiency when the SiOx content was less than 8 wt%, and low cycle stability when the content of SiOx was less than 20 wt%. The CB/SiOx/C composite containing 10 wt% of SiOx showed an initial discharge capacity of 537 mAh/g, a capacity retention rate of 88%, and a rate of 79 at 2C/0.1C. SiOx was added to improve the capacity of the soft carbon anode material, and carbon black was added as a structural stabilizer to buffer the volume change of SiOx. In order to use the CB/SiOx/C composite as a high-efficiency anode material, the mechanism of the optimal SiOx and the use of carbon black as a structural stabilizer was discussed.

• Journal of the Korean earth science society
• /
• v.41 no.6
• /
• pp.588-598
• /
• 2020

The seafloor geology of Ieodo, a submerged volcanic island, has been poorly understood, although this place has gained considerable attention for ocean and climate studies. The main purpose of the study is to understand and elucidate types, distribution patterns and provenance of the surficial sediments in and around the Ieodo area. For this purpose, 25 seafloor sediments were collected using a box-corer, these having been analyzed for grain sizes. XRD (X-ray Diffraction) analysis of fine-grained sediments was conducted for characterizing clay minerals. The peak of Ieodo exists in the northern region, while in the southern area, shore platforms occur. The extensive platform in the south results from severe erosion by strong waves. However, the northern peak still survived from differential weathering. Grain size analyses indicated that gravels and gravelly sands with skeletons and shells were distributed predominantly on the volcanic apron and shore platform. Muddy sediments were found along the Ieodo and the adjacent deeper seafloor. Based on the analysis of clay mineral composition, illites were the most abundant in fine muds, followed by chlorites and kaolinites. The ratio plots of clay minerals for the provenance discrimination suggested that the Ieodo muds were likely to be derived from the Yangtze River (Changjiang River). As a consequence, gravels and gravelly sands with bioclastics may be supplied from the Ieodo volcanic apron by erosion processes. Wave activities might play a major role in transportation and sedimentation. In contrast, fine muds were assumed to be derived from the inflow of the Yangtze River, particularly in summer. Deposition in the Ieodo area is, therefore, probably controlled by the inflow from the Changjiang Dilute Water and summer typhoons from the south.

• Clean Technology
• /
• v.30 no.2
• /
• pp.134-144
• /
• 2024

In this study, the mechanical stability of red mud was improved for its commercial use as a catalyst to effectively decompose HFC-134a, one of the seven major greenhouse gases. Red mud is an industrial waste discharged from aluminum production, but it can be used for the decomposition of HFC-134a. Red mud can be manufactured into a catalyst via the crushing-preparative-compression molding-firing process, and it is possible to improve the catalyst performance and secure mechanical stability through calcination. In order to determine the optimal heat treatment conditions, pellet-shaped compressed red mud samples were calcined at 300, 600, 800 ℃ using a muffle furnace for 5 hours. The mechanical stability was confirmed by the weight loss rate before and after ultra-sonication after the catalyst was immersed in distilled water. The catalyst calcined at 800 ℃ (RM 800) was found to have the best mechanical stability as well as the most catalytic activity. The catalyst performance and durability tests that were performed for 100 hours using the RM 800 catalyst showed thatmore than 99% of 1 mol% HFC-134a was degraded at 650 ℃, and no degradation in catalytic activity was observed. XRD analysis showed tri-calcium aluminate and gehlenite crystalline phases, which enhance mechanical strength and catalytic activity due to the interaction of Ca, Si, and Al after heat treatment at 800 ℃. SEM/EDS analysis of the durability tested catalysts showed no losses in active substances or shape changes due to HFC-134a abasement. Through this research, it is expected that red mud can be commercialized as a catalyst for waste refrigerant treatment due to its high economic feasibility, high decomposition efficiency and mechanical stability.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.267-274
• /
• 2006

Greenhouse gas reduction will be highlighted as the most pending question in the cement industry in future because the production of Portland cement not only consumes limestone, clay, coal, and electricity, but also release waste gases such as $CO_2,\;SO_3$, and NOX, which can contribute to the greenhouse effect and acid rain. To meet the increase of cement demand and simultaneously comply with the Kyoto Protocol, cement that gives less $CO_2$ discharge should be urgently developed. This study aims to manufacture non-sintering cement(NSC) by adding phosphogypsum(PG) and waste lime(WL) to granulated blast furnace slag(GBFS) as sulfate and alkali activators. This study also Investigates the hydration reaction of NSC through analysis of scanning electron microscopy(SEM), X-ray diffraction(XRD), differential thermal analysis(DTA), and pH. Results obtained from analysis of the hydrate have shown that the glassy films of GBFS are destroyed by the activation of alkali and sulfate, ions eluted from the inside of GBFS react with PG and produce ettringite, and consequently the remaining component in GBFS slowly produced C-5-H(I) gel. Here, PG is considered not only to play the role of simple activator, but also to work as a binder reacting with GBFS.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.13-18
• /
• 2010

The present study was undertaken to investigate the characteristic of suspended matter in soils of Imha-Dam area by turbidity. Soil sampling was conducted at 5 points of Yeongyang (Turbid area) and 2 points of Cheongsong (Clean area). Experimental analysis was conducted using those samples. The pH of water in the soils at turbid area was higher than that of clean area. X-ray diffraction analysis showed that every sample consists in mainly quartz, illite and feldspar before precipitation. After precipitation for 3 days, the content of quartz and feldspar was decreased and the content of illite was increased at turbid area. The soil of Sinheung (St. 6) at clean area was analyzed only illite. SEM-EDS analysis showed the much content of $SiO_2$ as to every sample before precipitation, but $K_2O$, MgO, $Al_2O_3$, CaO and $Fe2O_3$ with illite was increased after precipitation for 3 days as to every sample. Experimental results exhibited that the major mineral of turbid water was illite at turbid area and clean area.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.1
• /
• pp.41-47
• /
• 2020

Purpose: The purpose of this study was to evaluate the flexural strength and reliability of highly translucent colored zirconia for all ceramic restoration. Materials and Methods: Bar-shaped specimens (25 × 4 × 2.5 mm) were prepared from highly translucent monolithic zirconia. Three experimental groups were set up according to color (shade A0, A1, and A3). For each group, 20 specimens were prepared. Flexural strength was determined using a 3-point flexural test and results were analyzed with one-way ANOVA test. Weibull statistical analysis provided 2 parameter estimates: Weibull modulus and characteristic strength. X-ray diffraction (XRD) analysis was performed. Results: There was statistically significant difference between uncolored (Shade A0) and colored (shade A1 and A3) (P < 0.05), but there was no difference between colored groups (P > 0.05). The uncolored group had higher reliability compared with colored study groups. On x-ray diffraction analysis of each group, typical peaks of tetragonal phase appeared in all groups. Conclusion: Within the limitations of this in vitro study, coloring highly translucent zirconia had significant effect on flexural strength and reliability. Therefore, clinicians should be careful when using highly translucent colored zirconia to prevent breakage of veneering ceramic and enhance aesthetics.