• Journal of Korean Society of Water and Wastewater
• /
• v.28 no.5
• /
• pp.589-600
• /
• 2014

Tuberculation and slime accumulated in water mains play an important role in modifying water quality of drinking water. Therefore, in this study, it was investigated that what materials were accumulated, and what components were included in the tuberculation and slime of water mains. The Various tuberculation and slime sample were collected from the 12 water mains to analyze their physical and chemical properties and crystal structure. As a analysis method, VSS(Volatile suspended solid), SEM(scanning electron microscope), EDS(Energy Dispersive X-ray spectroscope), ICP(Inductively Coupled Plasma Mass Spectrometer) and XRD(X-Ray Diffractomete) were used. The results of analysis on the samples, the representative materials were verified such as iron corrosion products, the fine sand particles generated during backwash, fine particles of activated carbon, aluminum used in coagulation process, and manganese included in raw water.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.167-172
• /
• 2012

Fine diamond powders are synthesized with a 420 ${\phi}$ cubic press and stack-cell composed of Kovar ($Fe_{54}Ni_{29}Co_{17}$) (or Kovar+7 ${\mu}m$-thick Zn electroplated) alloy and graphite disks. The high pressure high temperature (HPHT) process condition was executed at $1500^{\circ}C$ for 280 seconds by varying the nominal pressure of 5.7~10.6 GPa. The density of formation, size, shape, and phase of diamonds are determined by optical microscopy, field emission scanning electron microscopy, thermal gravimetric analysis-differential thermal ammnlysis (TGA-DTA), X-ray diffraction (XRD), and micro-Raman spectroscopy. Through the microscopy analyses, we found that 1.5 ${\mu}m$ super-fine tetrahedral diamonds were synthesized for Zn coated Kovar cell with whole range of pressure while ~3 ${\mu}m$ super-fine diamond for conventional Kovar cell with < 10.6 GPa. Based on $750^{\circ}C$ exothermic reaction of diamonds in TGA-DTA, and characteristic peaks of the diamonds in XRD and micro-Raman analysis, we could confirm that the diamonds were successfully formed with the whole pressure range in this research. Finally, we propose a new process for super-fine diamonds by lowering the pressure condition and employing Zn electroplated Kovar disks.

• Membrane and Water Treatment
• /
• v.7 no.6
• /
• pp.495-505
• /
• 2016

Mesoporous MCM-41 was deposited on an inexpensive disk shaped ceramic support through hydrothermal technique for ultrafiltration of $Fe^{3+}$ from aqueous solution. The ceramic support was fabricated using uni-axial compaction technique followed by sintering at $950^{\circ}C$. The characteristics of MCM-41 powder as well as the composite membrane were examined by X-ray diffraction (XRD), thermogravimetric analysis (TGA), field emission scanning electron microscope (FESEM), porosity and pure water permeation test. The XRD result revealed the good crystallinity and well-resolved hexagonally arranged pore geometry of MCM-41. TGA profile of synthesized MCM-41 zeolite displayed the three different stepwise mechanisms for the removal of organic template. The formation of MCM-41 on the porous support was verified by FESEM analysis. The characterization results clearly indicated that the accumulation of MCM-41 by repeated coating on the ceramic disk directs to reduce the porosity and pore size from 47% to 23% and 1.0 to $0.173{\mu}m$, respectively. Moreover, the potential of the fabricated MCM-41 membrane was investigated by ultrafiltration of $Fe^{3+}$ from aqueous stream at various influencing parameters such as applied pressure, initial feed concentration and pH of solution. The maximum rejection 85% was obtained at applied pressure of 276 kPa and the initial feed concentration of 250 ppm at pH 2.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.456-461
• /
• 2012

The glycerol carbonate was synthesized by glycerol and urea using metal oxide catalysts. The physical properties of the prepared metal oxide catalysts were investigated by X-ray diffraction (XRD), specific surface area analysis (BET), field emission scanning electron microscopy (FE-SEM) and temperature programmed desorption (TPD). In addition, we confirmed the conversion of the glycerol and the yield of the glycerol carbonate according to characteristics of metal oxide catalysts. From XRD and FE-SEM analysis, the crystallite size and crystallinity of metal oxide catalysts decrease with addition of Al. In addition, the Zn-Al mixed metal oxide had higher catalytic activity than the pure ZnO due to decreased side reaction in the synthesis of glycerol carbonate.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.1
• /
• pp.34-44
• /
• 1998

Stainless steel is being used widely lor various purposes due to its good corrosion resistance. There has becn much research to produce colored stainless sterl by several methods. In this experiment, we coated TixN film on the SUS304 substrate with thc DC magnetron sputtering system and studied the internal structurc and adhesive strength of the films as a function of the coating conditions. Before lhe specimen was coated, a sputter etching was very effective in removing the$\delta$ Fe(BCC) phase as well as the contaminant and oxide layer as well as increasing rotghness. Five-stage failure mode appeared with increased scratch load with the TIN films coated on the SUS304 in this manner ; tensile failure-,conformal failure-,buckling failure->chipping failurc and spalling Failure. When the failure was terminated at the initial stage, the film will have good adhesion. But, if syalling failure has occurred at the initial scratch, then the adhesion will be poor. The interlayer between thc coated film and thc substratc was homogeneously adhcsive when the $\gamma'-Fe_4N$ phase wasn't detected in the XRD analysis and the adhesive strength only was reduced by surPace defects. But, when the ,$\gamma'-Fe_4N$N phasc was detected in the XRD analysis, the adhesive strength was very poor.

• Journal of the Korean Vacuum Society
• /
• v.11 no.3
• /
• pp.159-165
• /
• 2002

The physical properties of the TiN films deposited by ALD using $TiCl_4$and $NH_3$have been investigated. The TiN deposition rate is ~0.6 $\AA$ under an optimum deposition condition and the resistivity of the TiN films is 200~350 $\mu\Omega$cm . According to the XRD analysis results TiN films are crystallized in the ALD process window. AES analysis results show that the Cl impurity concentration in the TiN films is lower than 1 at% and that the atomic ratio of the TiN films is 1:1. Also it is found by SEM observation that the step coverage of the TiN films on which TiN films with trenches the aspect ratio of which is 10:1 is excellent.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.70-77
• /
• 2006

The butane decomposition over the catalyst is an attractive method for the hydrogen production. The objective of the work was investigated the catalysis of carbon black in butane decomposition reaction. The Butane decomposition was performed over carbon black catalyst in a range of $500-1100^{\circ}C$. The butane conversion of thermal decomposition and catalytic decomposition were increased with increasing the reaction temperature The butane conversion of the thermal decomposition was higher than the butane conversion of the catalytic decomposition. Hydrogen and methane were mostly observed in the butane decomposition over $1000^{\circ}C$. Especially, the hydrogen yield was steadily increased with raising the reaction temperature, It could be known that the hydrogen yield of the catalytic decomposition was higher than one of the thermal cracking because the hydrogen productivity was improved by the catalyst. The deactivation of the catalyst was not observed in the reactivity test. The surface and crystalline of the fresh and used catalysts were characterized by TEM, BET surface area and XRD analysis, respectively. The fresh carbon black particles had mostly smoothly round-shaped surfaces. In the surface of the carbon black after the reaction, the deposited carbon was formed as the protrusion-shaped carbon and the cone-shaped. The proper peaks of carbon black appeared in XRD analysis.

• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.126-131
• /
• 2018

In the present study, we investigate the effects of milling time and the addition of a process control agent (PCA) on the austenite stability of a nanocrystalline Fe-7%Mn alloy by XRD analysis and micrograph observation. Nanocrystalline Fe-7%Mn alloys samples are successfully fabricated by spark plasma sintering. The crystallite size of ball-milled powder and the volume fraction of austenite in the sintered sample are calculated using XRD analysis. Changes in the shape and structure of alloyed powder according to milling conditions are observed through FE-SEM. It is found that the crystallite size is reduced with increasing milling time and amount of PCA addition due to the variation in the balance between the cold-welding and fracturing processes. As a result, the austenite stability increased, resulting in an exceptionally high volume fraction of austenite retained at room temperature.

• Korean Journal of Materials Research
• /
• v.23 no.7
• /
• pp.399-403
• /
• 2013

The purpose of this study is to investigate the coloration characteristics by identifying the factor affecting red coloration of copper red glaze in traditional Korean ceramics. This study analyzed the characteristics of the reduction-fired copper red glaze by using XRD, Raman spectroscopy, EDX and UV-vis spectroscopy. As a result of XRD analysis, the glaze completely melted and amorphous glass appeared overall, and the characteristic peak of metal Cu was shown together. In addition, as a result of Raman analysis, the characteristic bands of CuO and $Cu_2O$ were shown together. The distribution of component elements was observed by EDX. As a result, copper(Cu) were distributed throughout the glaze. Thus, it was shown that copper red glaze appeared the best red coloration because metal Cu, CuO and $Cu_2O$ evenly existed throughout glaze in particle colloidal state. The chroma value of the copper red glaze was CIE $L^*$ 30.07, $a^*$ 13.65, $b^*$ 3.72. Wine-Red Solution was shown by Dark Graish Red coloration.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1133-1137
• /
• 1998

By the mechanical alloying method Ni-W(WC) composite materials were prepared to improve the resistance for creep and sintering of Ni-anode at the operating temperature of$ 650^{\circ}C$. Amorphization was observed from the XRD analysis of mechanically alloyed powder caused by the destruction of ordered crystals. Sintering was performed at $1280^{\circ}C$ for 10 hours in $H_2$ atmosphere. From the result of dot-mapping and TEM analysis the second phase was not observed at Ni-W interface while W particles of less 0.lam were distributed finely and uniformly in Ni matrix. This finely and uniformly distributed W in Ni matrix is expected to enhance the mechanical properties of Ni-anode through the dispersion and solid solution hardening mechanisms.