• Restorative Dentistry and Endodontics
• /
• v.29 no.2
• /
• pp.191-199
• /
• 2004

The purposes of this study were to estimate the material properties of the recently developed domestic composite resins for core filling material (Chemical, Dual A, Dual B；Vericom, Korea) and to compare them with other marketed foreign products (CorePaste, Den-Mat, USA；Ti-Core, Essential Dental Systems, USA；Support. SCI-Pharm. USA). Six assessments were made：working time. setting time. depth of polymerization. flexural strength. bonding strength. and marginal leakage. All items were compared to ISO standards. All domestic products satisfied the minimum requirements from ISO standards (working time：above 90 seconds. setting time：within 5 minutes). and showed significantly higher flexural strength than Core Paste. Dual A and B could. especially. reduce the setting time to 60 seconds when cured with $600mW/cm^2$ light intensity. All experimental materials showed 6 mm depth of polymerization. Bond strengths of Ti-Core and Dual B materials were significantly higher than the other materials. Furthermore. three domestic products and Ti-Core could reduce the microleakage effectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.338-338
• /
• 2007

Photo-conductive properties of CdS films deposited on glass substrates by a reactive sputtering in Ar atmosphere were characterized as a function of working pressure and the film thickness. The XRD measurements of CdS films revealed obvious (002) preferred orientation. In 300nm-thick of films, difference between dark and photo-resistance increases with increasing working pressure within the films. The films at 5 mTorr of working pressure show a dark resistance of approximately $1\;{\times}\;10^6\;{\Omega}/{\square}$ and a photo-resistance of $3\;{\times}\;10^4\;{\Omega}/{\square}$. The decrease dark- and photo-resistance of films as thickness decrease were $1.4\;{\times}\;10^6$ and $3\;{\times}\;10^4\;{\Omega}/{\square}$, respectively. CdS films deposited on glass substrates are considered tobe suitable for photo-conductivity materials in stealth radome applications.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.3
• /
• pp.116-121
• /
• 2021

This study was carried out to investigate the effect of transformation induced martensite on the tensile properties of Fe-20Mn-12Cr-3Ni-3Si alloy. α' and ε-martensite were formed by cold rolling, and these martensite were formed with according to the specific direction, surface relief and partially intersection. With an increasing degree of cold rolling, amount of α'-martensite was slowly increased, whereas amount of ε-martensite was rapidly increased. Volume fraction of ε-martensite formed by cold working was large than α'-martensite. Tensile strength was rapidly increase and elongation was rapidly decreased with an increasing of degree of cold rolling. This means that tensile strengh and elongation was greatly influenced by the volume fraction of ε-martensite formed by cold rolling then α'-martensite.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.89-92
• /
• 2009

As a class of materials, Ni-base superalloys are among the most difficult metal alloys to forge together with refractory metals and cobalt-base superalloys. The mechanical properties of Ni-base superalloys depend very much on grain size and the strengthening phases, $\gamma$' ($Ni_3$(Al,Ti)-type) and $\gamma$".($Ni_3$Nb-type). Especially, the control of grain size remains as a sole means for the control of mechanical properties. The grain size and distribution changes of the wrought superalloys during hot working and heat treatment are mainly controlled by the recrystallization and grain growth behaviors. In this presentation, prediction technology of grain size through the computer-aided process design, and numerical modeling for predicting the microstructure evolution of Ni-base superalloy during hot working were introduced. Also, some case studies were dealt with actual forming processes of Ni-base superalloys.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.93-96
• /
• 2017

The structural, electrical and optical properties of Ti thin films fabricated by dual magnetron sputtering were investigated under various film thicknesses. The fabricated Ti thin films exhibited uniform surfaces, crystallinity, various grain sizes, and with various film thicknesses. Also, the crystallinity and grain size of the Ti thin films increased with the increase of film thickness. The electrical properties of Ti thin films improved with the increase of film thickness. The results showed that the performance of TCO-less DSSC critically depended on the film thickness of the Ti working electrodes, due to the conductivity of Ti thin film. However, the maximum conversion efficiency of TCO-less DSSC was exhibited at the condition of 100 nm thickness due to the surface scattering of photons caused by the variation of grain size.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.8
• /
• pp.1236-1241
• /
• 2017

We deposited Al-doped ZnO (ZnO:Al) thin films on glass substrates ($200mm{\times}200mm$) by using in-line magnetron sputtering system. Effects of various deposition parameters such as working pressure, deposition power and substrate temperature on optoelectronic characteristics including surface-texture etching profiles were carefully investigated in this study. We found that relatively low working pressure and high deposition power offered to obtain enhanced conductivity and optical transmittance. Haze properties showed similar trend with the transmittance. Furthermore, surface-texture etching study exhibited good morphologies when the films were deposited at $200-300^{\circ}C$. On the basis of these optimizations, we could find the deposition region that produces highly transparent and conductive properties including efficient light scattering capability.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.449-452
• /
• 2003

The objective of this study is to investigate the basic properties of polyester mortars using ground calcium carbonate(GCC), blast furance slag(BFS), fly ash(FA), ordinary portland cement(OPC) as fillers. Particle size distribution, particle shape and resin absorption of GCC, BFS, FA and OPC are checked. Polyester mortars with GCC, BFS, FA and OPC are prepared with various MEKPO content and tested for working life. The flexural and compressive strengths of the polyester mortars with MEKPO content of 0.5phr are evaluated. As a test result, the average sizes of GCC, BFS, FA and OPC are 9.7$\mu\textrm{m}$, 11.6$\mu\textrm{m}$, 21.2$\mu\textrm{m}$, 29.9$\mu\textrm{m}$. Resin absorption of FA is 1.5times larger than other fillers. The polyester mortar with FA at a MEKPO content of 0.5phr has the longest working life and the maximum flexural and compressive strengths.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1277-1282
• /
• 2004

ITO films on PET substrate were prepared by DC magnetron sputtering method using powdery target with different deposition conditions. In addition, the electrical and optical properties were investigated. As the sputtering power and working pressure were higher, the resistvity of ITO films increased. The optical transmittance deteriorated with increasing sputtering power and thickness. As the working pressure increased, however, the optical transmittance improved at visible region of light. From these results, we could deposited ITO films with 8${\times}$10$^{-3}$ $\Omega$-cm of resistivity and 80 % of transmittance at optimal conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.165-165
• /
• 2010

AZO:H films were prepared by RF magnetron sputtering system with a AZO (2wt% $Al_2O_3$) ceramic target at a temperature of $150^{\circ}C$. The annealing treatments were carried out in hydrogen ambient for 1hr at a temperature of $400^{\circ}C$. The AZO:H films were etched with 1 % HCl. The influence of the properties of AZO:H films deposited in various working pressures is investigated. As a result, the AZO:H film deposited in 4mTorr showed excellent electrical property of $\rho=5.036{\times}10^{-4}{\Omega}cm$ and strongly oriented (002) peak. The transmittance in the wavelength of 450nm was above 80%. It can be used as front electrode for increasing efficiency of GaN LED.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.793-798
• /
• 2003

The purpose of this study is to investigate the setting properties of polystyrene mortars using waste expanded polystyrene(EPS) solution-based binders. The binders for polystyrene mortars are made by mixing crosslinking agent with waste EPS solutions which prepared by dissolving EPS in styrene. Polystyrene mortars are prepared with various EPS concentrations of EPS solutions and crosslinking agent contents, subjected to a dry curing, and tested for working life, peak exotherm temperature and 10h-length change. From the test results, the working lives of polystyrene mortars are shortened with raising EPS concentration of EPS solution and crosslinking agent content. Low-shrinkage or non-shrinkage of polystyrene mortars should be accomplished by adjusting EPS concentration of EPS solution and crosslinking agent content.