• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.689-695
• /
• 2012

The friction factor in a rod bundle and the loss coefficient at a spacer grid were examined. As a test section, 25 smooth rods, 9.5 mm in diameter and 2000 mm in length, were prepared and installed in a $5{\times}5$ square array in a square channel. In this case, the P/D (Pitch-to-Diameter ratio) was 1.35. In this work, plain (i.e., no mixing vanes), split-vane, and hybrid-vane spacer grids were tested. In a bare rod bundle (i.e., no spacer grid), the measured friction factors were in good agreement with the previous correlations. Among the spacer grids tested, the hybrid-vane spacer grid presented the largest friction factor in the rod bundle and loss coefficient. This may be because of the flow pattern change induced by large relative plugging of the flow cross section and mixing vane geometry. At Re=$5{\times}10^5$, the predicted loss coefficients of plain, splitvane, and hybrid-vane spacer grids were approximately 0.79, 0.80, and 0.88, respectively.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.14
• /
• pp.5635-5641
• /
• 2015

Background: Cirrhosis is regarded as a possible end stage of many liver diseases, including viral infection. It occurs when healthy liver tissue becomes damaged and is replaced by scar tissue and finally may lead to hepatocellular carcinoma. Interferons (IFNs)are two general categories, type I and II. Type I includes one beta interferon and over 20 different alpha interferons. Alpha interferons are very similar in how they work, interacting with other proteins on cells like receptors. The main objective of this study was to compare Mx gene productivity post different cell line treatment with imported and Egyptian biosimilar locally produced IFNs, as well as the efficacy of those tested IFNs. Also, an assessment was made of sensitivity of different cell lines as alternatives to that recommended for evaluation of antiviral activity. Materials and Methods: Different cell lines (Vero, MDBK and Wish) were employed to evaluate cytotoxicity using the MTT assay. Antiviral activity was evaluated compared with standard IFN against VSV, Indiana strain -156, on tested rh-IFNs (imported; innovated and Egyptian biosimilar locally produced IFNs) in the pre-treated cell lines previously mentioned. The virus was propagated in the Wish cell line as recommended. Finally we estimated up-regulation of the Mx gene as a biomarker. Results: Data recorded revealed that test IFNs were safe in test cell lines. Viability was around 100%. Locally tested interferon did not realize the international potency limits, while the imported one was accepted compared with the standard IFN. These results were the same either using infectivity titer reduction assay or crystal violet staining of residual non- infected cells. Mx protein production was cell type related and confirmed by the detected Mx gene expressed in imported and locally produced IFN pre-treated cell lines. The expression of the gene was arranged in the order of Vero> wish > MDBK for the imported IFN, while for the Egyptian biosimillar locally produced one it was MDBK> Vero> wish. With regard to the antiviral activity there was a significant difference of imported IFN potency compared with the locally produced IFN (P<0.05), the IFN potential (antiviral activity) was not cell line related and showed non-significant difference for each separate product. Conclusions: Vero cells can be used as an alternative cell line for evaluation of IFN potency in case of unavailable USP recommended cell lines. Alternative potency evaluation assay could be used and proved significant difference in IFN potency in case of local and imported agents. Evaluation of antiviral activity could be used in parallel to viral infectivity reduction assay for better accuracy. Mx gene can be used as a marker for IFN potential.

• Applied Microscopy
• /
• v.33 no.2
• /
• pp.105-116
• /
• 2003

In Vitro fertilization of U. unicinctus eggs observed by immunofluorescence and electron microscopes revealed an overview of the meiotic pattern of the tide animals. The eggs have been fertilized early at germinal vesicle stage, followed by germinal vesicle break down (GVBD), but pre-mitotic aster like structure could not be resolved by the methods employed in this work. The meiotic features, such as rotation-shift movement of spindle fibers, behavior of spermatozoonmonaster in the egg cytoplasm and active spindle fiber of the 1st polar body, have been observed. The antitubulin-FITC fluorescence show the 2nd meiotic apparatus appeared firstly parallel to the tangential line of the oolemma, proceeding the meiosis, its bipolarity is rotated and shifted towards the oolemma. The polar bodysite of the oolemma was not amorphous, but active in a sense of anti-tubulin-FITC reactions during the extrusions of the polar bodies. The immunofluorescence reactions of the spermatozoon centriole appeared at a later stage of the 2nd meiosis. During the time periods, the fertilized spermatozoon resided in the egg cytoplasm. Activating the centrioles, spermatozoon approaches towards the chromosomal materials of the 2nd oocyte. This suggests that spermatozoon centrioles initiate and play a roll to fuse male and female pronuclei.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.8
• /
• pp.181-188
• /
• 2016

Recently, as the amount of spatial information increases, an interest in the study of spatial information processing has been increased. Spatial database systems extended from the traditional relational database systems are difficult to handle large data sets because of the scalability. SpatialHadoop extended from Hadoop system has a low performance, because spatial computations in SpationHadoop require a lot of write operations of intermediate results to the disk, resulting in the performance degradation. In this paper, Spatial Computation Spark(SC-Spark) is proposed, which is an in-memory based distributed processing framework. SC-Spark is extended from Spark in order to efficiently perform the spatial operation for large-scale data. In addition, SC-Spark based on the GPGPU is developed to improve the performance of the SC-Spark. SC-Spark uses the advantage of the Spark holding intermediate results in the memory. And GPGPU-based SC-Spark can perform spatial operations in parallel using a plurality of processing elements of an GPU. To verify the proposed work, experiments on a single AMD system were performed using SC-Spark and GPGPU-based SC-Spark for Point-in-Polygon and spatial join operation. The experimental results showed that the performance of SC-Spark and GPGPU-based SC-Spark were up-to 8 times faster than SpatialHadoop.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.27 no.1
• /
• pp.38-45
• /
• 2017

Objectives: Radon may be second only to smoking as a cause of lung cancer. Radon is a colorless, tasteless radioactive gas that is formed via the radioactive decay of radium. Therefore, radon levels can build up based on the amount of radium contained in construction materials such as phospho-gypsum board or when ventilation rates are low. This study provides our findings from evaluation of radon gas at facilities and offices in an industrial complex. Methods: We evaluated the office rooms and processes of 12 manufacturing factories from May 14, 2014 to September 23, 2014. Short-term data were measured by using real-time monitoring detectors(Model 1030, Sun Nuclear Co., USA) indoors in the office buildings. The radon measurements were recorded at 30-minute intervals over approximately 48 hours. The limit of detection of this instrument is $3.7Bq/m^3$. Also, long-term data were measured by using ${\alpha}-track$ radon detectors(${\alpha}-track$, Rn-tech Co., Korea) in the office and factory buildings. Our detectors were exposed for over 90 days, resulting in a minimum detectable concentration of $7.4Bq/m^3$. Detectors were placed 150-220 cm above the floor. Results: Radon concentrations averaged $20.6{\pm}17.0Bq/m^3$($3.7-115.8Bq/m^3$) in the overall area. The monthly mean concentration of radon by building materials were in the order of gypsum>concrete>cement. Radon concentrations were measured using ${\alpha}-track$ in parallel with direct-reading radon detectors and the two metric methods for radon monitoring were compared. A t-test for the two sampling methods showed that there is no difference between the average radon concentrations(p<0.05). Most of the office buildings did not have central air-conditioning, but several rooms had window- or ceiling-mounted units. Employees could also open windows. The first, second and third floors were used mainly for office work. Conclusions: Radon levels measured during this assessment in the office rooms of buildings and processes in factories were well below the ICRP reference level of $1,000Bq/m^3$ for workplaces and also below the lower USEPA residential guideline of $148Bq/m^3$. The range of indoor annual effective dose due to radon exposure for workers working in the office and factory buildings was 0.01 to 1.45 mSv/yr. Construction materials such as phospho-gypsum board, concrete and cement were the main emission sources for workers' exposure.

• Journal of the Korean Chemical Society
• /
• v.37 no.12
• /
• pp.995-1002
• /
• 1993

The thermal decomposition of trimethylaluminum (TMA) with ammonia has been investigated by in-situ Fourier transform infrared spectroscopy. The spectroscopic reaction cell, which permits heating interna lly up to 1100$^{\circ}C$, consists of stainless-steel hexagonal-port chamber containing two NaCl windows installed in parallel. In this work, the stoichiometric reaction between TMA and $NH_3$ is found to be completed immediately after mixing. FTIR spectra observed in the range of temperature 25∼1100$^{\circ}C$ show that TMA and TMA : $NH_3$ adduct decompose into methane as a predominant product around 500$^{\circ}C$. The assignments of the IR bands due to the gaseous TMA, $NH_3$ and TMA : $NH_3$ adduct are attempted on the basis of the published data. Furthermore, the decomposition of TMA can be described as a first-order reaction. Kinetic data about the decompositon of TMA and TMA : $NH_3$adduct will also be discussed.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.285-295
• /
• 2018

Purpose: The aim of this study is to develop a three-wheel riding cultivator for improving the performance of the current four-wheel riding cultivators in the market. Methods: A prototype three-wheel riding cultivator with the rated power of 15.5-kW, a primary hydrostatic and a two-speed selective gear transmission shifts, front/rear three-wheel drive, a hydraulic wheel tread adjustment, and the mid-section attachment of the major implements was designed and constructed. Its specifications and basic performance are investigated. Results: The maximum speeds of the prototype at the low and high stages were measured to be approximately 7.31, and 11.29 km/h in forward travel, respectively, and approximately 3.60, and 6.37 km/h in rearward travel, respectively. The minimum ground clearance is shown to be 670 mm. The rotating speeds of the power takeoff (PTO) shaft at the low and high stages are shown to be approximately 795 and 1,140 rpm, respectively. The tread of the rear wheels, the minimum radius of turning, and the maximum lifting height of the parallel link device are measured to be within 1,320-1,720 mm, 2.80 m, and 390 mm, respectively. Approximately 25.3% and 74.7% of the total weight of the prototype are distributed in the front and rear wheels on flat ground, respectively. When the tread of rear wheels increased from 1,320 to 1,720 mm, the left and right static lateral overturning angles increased from $33.4^{\circ}$ to $39.1^{\circ}$ and from $29.0^{\circ}$ to $36.1^{\circ}$, respectively. Conclusions: The prototype three-wheel riding cultivator showed a wide range of travel and PTO speeds, high minimum ground clearance, small minimum radius of turning, and easy control of the rear wheel tread. Further, the easy observation of cultivating operations by mid-mounting the implements can improve quality of work. Therefore, the prototype is expected to contribute to the riding mechanization of cultivating operations for various upland crops in Korea.

• Cross-Cultural Studies
• /
• v.49
• /
• pp.229-248
• /
• 2017

This paper is a study on French of Lee Sang's poems called metaphysical scandals in Korean poetry. Is poetic language he used a common poetic word or a non-poetic word in French? What kind of harmony do words and sentences composed of French have with Korean, Chinese character, and non-poetic word? Based on these questions, we analyzed a command of French, that is symbolic, geometrical, and pictorial French as well as repetitive and parallel constitution used in form of words and sentences. In Lee Sang's poems, as a result, the use of French is seen as a mixture of non-poetic word. It shows characteristics that reject traditional native language and the creation of poetry. In his poems, French is also an important factor of avant-garde poetic material and experimental creation technique. In his poems, French is used as a special tool to express internal conflicts of the poet. Lee Sang showed experimental style that could not be found in modern Korean literature by using signifier and signifed that french language has.

• Journal of Intelligence and Information Systems
• /
• v.27 no.1
• /
• pp.151-176
• /
• 2021

As the information technology industry develops, various kinds of data are being created, and it is now essential to process them and use them in the industry. Analyzing and utilizing various digital data collected online and offline is a necessary process to provide an appropriate experience for customers in the industry. In order to create new businesses, products, and services, it is essential to use customer data collected in various ways to deeply understand potential customers' needs and analyze behavior patterns to capture hidden signals of desire. However, it is true that research using data analysis and UX methodology, which should be conducted in parallel for effective service development, is being conducted separately and that there is a lack of examples of use in the industry. In thiswork, we construct a single process by applying data analysis methods and UX methodologies. This study is important in that it is highly likely to be used because it applies methodologies that are actively used in practice. We conducted a survey on the topic to identify and cluster the associations between factors to establish customer classification and target customers. The research methods are as follows. First, we first conduct a factor, regression analysis to determine the association between factors in the happiness data survey. Groups are grouped according to the survey results and identify the relationship between 34 questions of psychological stability, family life, relational satisfaction, health, economic satisfaction, work satisfaction, daily life satisfaction, and residential environment satisfaction. Second, we classify clusters based on factors affecting happiness and extract the optimal number of clusters. Based on the results, we cross-analyzed the characteristics of each cluster. Third, forservice definition, analysis was conducted by correlating with keywords related to happiness. We leverage keyword analysis of the thumb trend to derive ideas based on the interest and associations of the keyword. We also collected approximately 11,000 news articles based on the top three keywords that are highly related to happiness, then derived issues between keywords through text mining analysis in SAS, and utilized them in defining services after ideas were conceived. Fourth, based on the characteristics identified through data analysis, we selected segmentation and targetingappropriate for service discovery. To this end, the characteristics of the factors were grouped and selected into four groups, and the profile was drawn up and the main target customers were selected. Fifth, based on the characteristics of the main target customers, interviewers were selected and the In-depthinterviews were conducted to discover the causes of happiness, causes of unhappiness, and needs for services. Sixth, we derive customer behavior patterns based on segment results and detailed interviews, and specify the objectives associated with the characteristics. Seventh, a typical persona using qualitative surveys and a persona using data were produced to analyze each characteristic and pros and cons by comparing the two personas. Existing market segmentation classifies customers based on purchasing factors, and UX methodology measures users' behavior variables to establish criteria and redefine users' classification. Utilizing these segment classification methods, applying the process of producinguser classification and persona in UX methodology will be able to utilize them as more accurate customer classification schemes. The significance of this study is summarized in two ways: First, the idea of using data to create a variety of services was linked to the UX methodology used to plan IT services by applying it in the hot topic era. Second, we further enhance user classification by applying segment analysis methods that are not currently used well in UX methodologies. To provide a consistent experience in creating a single service, from large to small, it is necessary to define customers with common goals. To this end, it is necessary to derive persona and persuade various stakeholders. Under these circumstances, designing a consistent experience from beginning to end, through fast and concrete user descriptions, would be a very effective way to produce a successful service.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.2
• /
• pp.43-71
• /
• 1999

This research is an experimental work of developing a construction material using municipal wastewater sludge as liner and cover materials for waste disposal landfill. Weathered granite soil and flyash, produced as a by-product in the power plant, were used as the primary additives to improve geotechnical engineering properties of sludge. For secondary additives, bentonite and cement were mixed with sludge to decrease the permeability and to increase the shear strength, respectively. Various laboratory test required to evaluate the design criteria for liner and cover materials, were carried out by changing the mixing ratio of sludge with the additives. Basic soil properties such as specific gravity, grain size distribution, liquid and plastic limits were measured to analyze their effects on permeability, compaction, compressibility and shear strength properties of mixtures. Laboratory compaction tests were conducted to find the maximum dry densities and the optimum moisture contents of mixtures, and their effectiveness of compaction in field was consequently evaluated. Permeability tests of variable heads with compacted samples, and the stress-controlled consolidation tests with measuring permeabilities of samples during consolidation process were performed to obtain permeability, and to find the compressibility as well as consolidational coefficients of mixtures, respectively. To evaluate the long term stability of sludges, creep tests were also conducted in parallel with permeability tests of variable heads. On the other hand, for the compacted sludge decomposed for a month, permeability tests were carried out to investigate the effect of decomposition of organic matters in sludges on its permeability. Direct shear tests were performed to evaluate the shear strength parameters of mixed sludge with weathered granite, flyash and bentonite. For the mixture of sludge with cement, unconfined compression tests were carried out to find their strength with varying mixing ratio and curing time. On the other hand, CBR tests for compacted specimen were also conducted to evaluate the trafficability of mixtures. Various test results with mixtures were assessed to evaluate whether their properties meet the requirements as liner and cover materials in waste disposal landfill.