• Advances in concrete construction
• /
• v.4 no.2
• /
• pp.123-143
• /
• 2016

Use of heavy fuel fly ash (HFFA) (diesel and cracked fuel) for power generation in Saudi Arabia has generated and accumulated large quantities of HFFA as a byproduct. In this research, HFFA is studied with the emphasis on the utilization of this waste material in concrete blocks and asphalt concrete mixes. Two types of mixes, one with low and other with high cement content, were studied for concrete blocks. Different mixes having varying percentages of HFFA (0% to 25%), as cement/sand replacement or as an additive, were studied. The performance of concrete blocks is evaluated in terms of compressive strength, water absorption, durability and environmental concerns. The results showed that blocks cannot be cast if more than 15% HFFA is used; also there is a marginal reduction in the strength of all the mixes before and after being exposed to the sulfate solution for a period of ten months. HFFA is studied in asphalt concrete mixes in two ways, as an asphalt modifier (3&5%) and as a filler (50%) replacement, the results showed an improvement in stiffness and fatigue life of mixes. However, the stability and indirect tensile strength loss were found to be high as compared to the control mix due to moisture damage, indicating a need of using antistripping agents. On environmental concerns, it was found that most of the concerned elements are within acceptable limits also it is observed that lower concentration of barium is leached out with the higher HFFA concentrations, which indicates that HFFA may work as an adsorbent for this leaching element.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3883-3891
• /
• 1996

Performance and productivity of robot manipulator can be improved by increasing its working speed and extending its link length. But heavy weght of the commercial robot links, considered as "rigid body", limits its mazimum working speed and the weght of the links can be reduced for high speed operation. But this light-weight link or long link for special use cannot be consideredas "rigid" structure and vibration of the link due to its flexibility causes errors in end-effector position and orientation. Thus the elastic behaviro of the flexible link should be taken care of for increasing work speed and getting smaller error of end-effector position. In this paper, the fuzzy control theory is selected to design the controller which controlos the joint positions of the robot manipulator and suppress the vibration of flexible link. In the forst place, for the 1 DOF flexible link system, the fuzzy control theory is implemented. The contdroller for the 1 DOF flexible link system is designed. Experimental research is carried out to examine the controllability and the validity of the fuzzy control theory based controller. Next, using the extended desing schemes for the case of the 1 DOF flexible link system and usign the experimental phenomena of the 3 DOF flexible link system, the fuzzy controller for the 3 DOF flexible link system is desinged and experimented.ed and experimented.

• Journal of the Ergonomics Society of Korea
• /
• v.32 no.4
• /
• pp.405-411
• /
• 2013

Objective: Product design process without considering the strength of the user can cause the excessive burden on musculoskeletal system of human body. Since the muscle strength will vary depending on the body posture, the design of product should consider the characteristics of body posture. This study was performed to investigate the effects of forearm postures on the push and pull strength. Background: Overexerted force has been identified to cause musculoskeletal disorders. It is important to know the push and pull strength exerted by human when designing so that exerted force does not exceed the safety limits. Method: Maximum isometric push and pull strength of left, right and both hands were measured according to forearm postures with pronation, neutral and supination. For the study, 66 male and 30 female undergraduate students were participated as subjects. All subjects were normal and healthy with no clinical history. Results: The results showed that the push strength of male and female were 93.3% and 85.4% of pull strength. It showed that the strength of one-hand was 72.1~81.0% of the strength of two-hands, and the strength of left hand was 93.1~95.8% of the strength of right hand. The strength of female was 62% of the one of male. It was found that the strength with pronation $90^{\circ}$ was reduced up to 20% compared to the strength with neutral posture. Conclusion: Push and pull strength of male and female were reduced when forearm was rotated extremely. Application: The results of this study will be used for the prevention of work related musculoskeletal disorders and design of industrial equipment.

• Journal of the Ergonomics Society of Korea
• /
• v.32 no.4
• /
• pp.321-331
• /
• 2013

Objective: The aim of this study is to review the literatures on the regulation, standard and guideline for the human vibration in Korea and other countries. Background: This review can be used to prevent various diseases caused by the human vibration as a basis for the development of the policy. Results: In Korea, the general employers' duties related to human vibration are set forth the Health Measures(Article 24) in the Occupational Safety and Health Act. And then an employer shall take measures to protect the health of the workers concerned by improving other working conditions relating to working hours for the vibration prevention measures referred to in Article 24 of the Act. The European Union adopted a Directive in 2002 on minimum requirements for the health and safety of workers exposed to vibration. New Regulations on Vibration at Work will be introduced in Great Britain on 2005 to implement the Directive. In the U.S., both ANSI and ACGIH adopted the ISO standard for measurement and suggested exposure action and limit values. In Japan, the Ministry of Labor decided that the vibration syndrome among operators of rock drills and riveters etc. could be included in an occupational disease(1947). In addition, ISO standard was based on proposals and draft documents of many countries such as U.K, Japan and European, etc. Conclusion: In Korea, Occupational Safety and Health Act prevent vibration to health, but do not include exposure limits. It is therefore important to consider the new duties regarding to vibration risks added to the general duties.

• Journal of Hydrogen and New Energy
• /
• v.24 no.1
• /
• pp.50-60
• /
• 2013

High temperature proton exchange membrane fuel cells (PEMFCs) using phosphoric acid (PA) doped polybenzimidazole (PBI) membranes have been concentrated as one of solutions to the limits with traditional low temperature PEMFCs. However, the amount of reported experimental data is not enough to catch the operational characteristics correlated with cell performance and durability. In this study, design of experiments (DOE) based operational optimization method for high temperature PEMFCs has been proposed. Response surface method (RSM) is very useful to effectively analyze target system's characteristics and to optimize operating conditions for a short time. Thus RSM using central composite design (CCD) as one of methodologies for design of experiments (DOE) was adopted. For this work, the statistic models which predict the performance and degradation rate with respect to the operating conditions have been developed. The developed performance and degradation models exhibit a good agreement with experimental data. Compared to the existing arbitrary operation, the expected cell lifetime and average cell performance during whole operation could be improved by optimizing operating conditions. Furthermore, the proposed optimization method could find different new optimal solutions for operating conditions if the target lifetime of the fuel cell system is changed. It is expected that the proposed method is very useful to find optimal operating conditions and enhance performance and durability for many other types of fuel cell systems.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.864-867
• /
• 2007

Recent advancement in ICT and IT infrastructure drives the construction industry towards a IT-based industry. Accordingly, the importance of the planning phase of a project is significantly highlighted due to recent large-scale national development projects such as U-city and multifunctional administration city. various development and studies are conducted on the convergence of 3D CAD and GIS in order to support the decision making by simulation of each phase of construction prior to the actual construction of a building. However there has been limits to the implementation of the IT technology in the planning phase due to its characteristics such as high reliability on the experts knowledge and the compliance of the administration work. In this study, a trendy issue of the convergence of the GIS technology with the 3D CAD design data is suggested to improve the efficiency of a decision support in the planning phase.

• Korean Institute of Interior Design Journal
• /
• v.16 no.4
• /
• pp.110-118
• /
• 2007

Technology has been viewed at various stages of civilization as leading to future progress. The building, its services systems and management of the work process all contribute to the well-being of people within an organization. Productivity relies on there being a general sense of high morale and satisfaction with the workplace. Now buildings are considered as providing a milieu for human creativity. Flexibility, adaptability, service integration and high standards of finishes offer an intelligence threshold. Building Automation System(BAS) - controlled lighting systems may offer incremental energy saving. Conventional Lighting control systems often control equipment in a single room or over the limited area, because they are centralized control systems, which means that all the controlled circuits must be wired to a single control panel. The computers used by these systems are typically dedicated microprocess that perform only lighting control functions. By comparison, modern Building automation systems are distributed control system, which means that their computing hardware and software are distributed as a network that microprocessor-based control modules and standard PC. PLC(Programmable Logic controller) is extensible virtually without limits, so that all the lighting in a facility can be controlled by single, unified system - the same system that also can control and monitor the building's HVAC, security, and manufacturing processed, elevators, and more. A Building automation system can control light using schedules, manual controls, occupancy sensors, and photosensors, either singly or in combination. Building Lighting control and monitoring system will be for a energy saving and efficient building management system.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.1-2
• /
• 2000

In chip plating, several parameters must be taken into consideration. Current density, solution concentration, pH, solution temperature, components volume, chip and media ratio, barrel geometrical shape were most likely found to have an effect to the process yields. The 3 types of barrels utilized in chip plating industry are the onventional rotating barrel, vibrational barrel(vibarrel), and the centrifugal type. Conventional rotating barrel is a close type and is commonly used. The components inside the barrel are circulated by the barrel's rotation at a horizontal axis. Process yield has known to have higher thickness deviation. The vibrational barrel is an open type which offers a wide exposure to electrolyte resulting to a stable thickness deviation. It rotates in a vertical axis coupled with multi-vibration action to facilitate mixed up and easy transportation of components. The centrifugal barrel has its plated work centrifugally compacted against the cathode ring for superior electrical contact with simultaneous rotary motion. This experiment has determined the effect of barrel vibration intensity to the plating thickness distribution. The procedures carried out in the experiment involved the overall plating process., cleaning, rinse, Nickel plating, Tin-Lead plating. Plating time was adjusted to meet the required specification. All other parameters were maintained constant. Two trials were performed to confirm the consistency of the result. The thickness data of the experiment conducted showed thatbthe average mean value obtained from higher vibrational intensity is nearer to the standard mean. The distribution curve shown has a narrower specification limits and it has a reduced variation around the target value. Generally, intensity control in vi-barrel facilitates mixed up and easy transportation of components. However, it is desirable to maintain an optimum vibration intensity to prevent solution intrusion into the chips' internal electrode. A cathodic reaction can occur in the interface of the external and internal electrode. 2H20 + e $\rightarrow$M/TEX> 20H + H2.. Hydrogen can penetrate into the body and create pressure which can cause cracks. At high intensity, the chip's motion becomes stronger, its contact between each other is delayed and so plating action is being controlled. However, the strong impact created by its collision can damage the external electrode's structure there by resulting to bad plating condition.

• Korean Institute of Interior Design Journal
• /
• v.18 no.6
• /
• pp.96-103
• /
• 2009

Man has an unconscious desire to free oneself from everyday selves and a strong intellectual desire to see and analyze things in a different perspective. This provided a momentum for architectural design that has long been confined to its limits of modernism of being rational and objective. The ever-changing society that we live in filled with various attempts and pluralistic characteristics shows a complex set of attributes that can hardly be defined by a single term. As society moves towards an uncertain and volatile state, the boundary between literature, philosophy and art has dimmed out and converged. Such tendencies have been observable in recent establishments in architecture in the form of introducing external elements and create an alien and farfetched architectural space. Using the 'depaysement' defamiliarization method expressing irrationality and randomness, it is applied in various aspects, sharing the counter-rational structure and features of such architectural space. Hence, it is the purpose of this study to delve into the unique characteristics of depaysement through Magritte's work which reflects the unique pictorial world built under the influence of surrealism, and discover the $D\acute{e}paysement$ tendencies in modern architectural space. It is apparent in Modern architecture that, owing to the development in digital technology, it is showing process changes in design and an interfacial $D\acute{e}paysement$ effect in cyberspace, an interlace of reality and the virtual world. In this study, the focus of analysis was architectural properties such as the program, figure/spatial, material and the objective side, but due to mutual text properties, it is bound to be an overlapping analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.242-242
• /
• 2006

Increasingly complex tasks are performed by computers or cellular phone, requiring more and more memory capacity as well as faster and faster processing speeds. This leads to a constant need to develop more highly integrated circuit systems. Therefore, there have been numerous studies by many engineers investigating circuit patterning. In particular, PCB including module/package substrates such as FCB (Flip Chip Board) has been developed toward being low profile, low power and multi-functionalized due to the demands on miniaturization, increasing functional density of the boards and higher performances of the electric devices. Imprint lithography have received significant attention due to an alternative technology for photolithography on such devices. The imprint technique. is one of promising candidates, especially due to the fact that the expected resolution limits are far beyond the requirements of the PCB industry in the near future. For applying imprint lithography to FCB, it is very important to control thermal properties and mechanical properties of dielectric materials. These properties are very dependent on epoxy resin, curing agent, accelerator, filler and curing degree(%) of dielectric materials. In this work, the epoxy composites filled with silica fillers and cured with various accelerators having various curing degree(%) were prepared. The characterization of the thermal and mechanical properties wasperformed by thermal mechanical analysis (TMA), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), rheometer, an universal test machine (UTM).