• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1077-1088
• /
• 2006

This paper describes a numerical investigation on the performance deteriorations of a low speed, single-stage axial turbine due to use of rough blades. Numerical calculations have been carried out with a commercial CFD code, CFX-Tascflow, by using a modified wall function to implement rough surfaces on the stator vane and rotor blade. To assess the stage performance variations corresponding to 5 equivalent sand-grain roughness heights from a transition ally rough regime to a fully rough regime, stage work coefficient and total to static efficiency were chosen. Numerical results showed that both work coefficient and stage efficiency reduced as roughness height increased. Higher surface roughness induced higher blade loading both on the stator and rotor which in turn resulted in higher deviation angles and corresponding work coefficient reductions. Although, deviation angle changes were small, a simple sensitivity analysis suggested that their contributions on work coefficient reductions were substantial. Higher profile loss coefficients were predicted by higher roughness heights, especially on the suction surface of the stator and rotor. Furthermore sensitivity analysis similar to the above, suggested that additional profile loss generations due to roughness were accountable for efficiency reductions.

• Journal of Industrial Convergence
• /
• v.21 no.9
• /
• pp.11-21
• /
• 2023

There have been many studies to improve the efficiency of the CG production process, but it was not easy to overcome the problem that it was difficult to check the result in the middle of work and it took a lot of time for rendering. However, as the possibility of using Unreal Live Link, which can check the result in real-time, is increasing, expectations for improving the efficiency of the production process are rising. This study analyzed the efficiency of the 3D animation production process using Unreal Live Link. To this end, modeling, rigging, animation, and layout work were done in Maya, and the final output image sequence was rendered in Unreal Engine through Unreal Live Link. And the difference between this production process and the existing production process in which the final output image sequence is rendered in the 3D software itself was compared and analyzed. As a result of the analysis, unlike the traditional 3D animation production process, it was possible to check the final work result in real-time by proceeding with the work through a high-quality viewport screen, and it was found that the efficiency of work was maximized by deriving the final result through real-time screen capture. Recently, the use of game engines in the 3D animation and film industry is gradually increasing, and the efficiency of work is expected to be maximized if Unreal Live Link is used.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.3
• /
• pp.205-213
• /
• 2019

Recently, because of the global recession of the offshore plant industry and low-cost orders, there has been increasing interest in strengthening the competitiveness of domestic companies for the design and production technologies of offshore plants. However, in the offshore plant design field, the Plant Design Management System (PDMS), which is a 3D CAD program for plant layout developed by AVEVA Marine, is already commonly used as offshore plant design software and widely used in large domestic shipyards and cooperative design companies. Under this background, we have been thinking about ways to design better with the existing software. In this study, we developed a parametric design program to maximize the efficiency and reduce the working time for offshore plant electrical outfit production design based on the Programmable Macro Language (PML) of PDMS. We also examined its performance. By applying the developed program to the offshore plant module selected as an application example, it was confirmed that a 50% improvement in the work efficiency of cable tray design could be obtained compared with the existing method, with work efficiency improvements of 80% or more in other field design work.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.5 no.6
• /
• pp.1-6
• /
• 1982

The objective of this thesis to Provide a better insight into the effect of the amount of in-process storage has on the efficiency of production line with variable operation times. It is assumed that the material enters the line at the first work station and is then processed progressively through the line until it exits at the last work station, a finite amount of in-process storage is provided before all but the first work station of the line and the operation time of the work stations are statistically independent and follow exponential distribution. Under the above assumption, optimum allocation model is developed and following two approaches are used : 1) Given the available storage capacity, optimum allocation which minimizes the number of items in the line. 2) Given the available storage capacity, optimum allocation which. maximizes the utilization factor of the line. In a balanced three stage line, the production line efficiency is maximized under both categories when the second in-process storage is larger than the first.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1271-1276
• /
• 2020

The geometrical efficiency of a source-to-detector configuration is considered to be necessary in the calculation of the full energy peak efficiency, especially for NaI(Tl) and HPGe gamma-ray spectroscopy detectors. The geometrical efficiency depends on the solid angle subtended by the radioactive sources and the detector surfaces. The present work is basically concerned to establish a new mathematical approach for calculating the solid angle and geometrical efficiency, based on conversion of the geometrical solid angle of a non-axial radioactive point source with respect to a circular surface of the detector to a new equivalent geometry. The equivalent geometry consists of an axial radioactive point source with respect to an arbitrary elliptical surface that lies between the radioactive point source and the circular surface of the detector. This expression was extended to include coaxial radioactive circular disk source. The results were compared with a number of published data to explain how significant this work is in the efficiency calibration procedure for the γ-ray detection systems, especially in case of using isotropic radiating γ-ray sources in the form of point and disk shapes.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.6
• /
• pp.799-804
• /
• 1999

Particle collection characteristics of the MOUDI cascade impactor has been studied for coarse particles in the range of 2 to 20$mu extrm{m}$ in aerodynamic diameter. A vibrating orifice aerosol generator was empolyed to generate monodisperse test aerosols. The oleic acid and sodium chloride(NaCl) particles were used as test aerosols. Aluminum foil and Teflon filter were selected as impaction media. The sampling flow rate was changed from 25 to 35L/min. Particle collection efficiency for single stage was examined for liquid particles. The stage response was obtained experimentally for the cascade impactor composed of three stages and a backup filter. The results showed that most of particle collection efficiencies measured in this work are similar to the efficiency curves obtained by Marple et al.(1991). For particles less than cut-off size of the stage, the collection efficiencies of solid particles are similar to those of loquid particles. However, the collection efficiency of solid particles decreases with mereasing particle diameter for the particles greater than the actual cut-off size of the impactor. The particle collection efficiency increases with increasing sampling flow rate at the same particel size. However, the collection efficiency curves seem not to be greatly shifted with the flow rate. The stage responses obtained by direct measurements in this work are in good agreement with those derived from the collection efficiency curves for single stage.

• Journal of Industrial Technology
• /
• v.28 no.A
• /
• pp.113-117
• /
• 2008

Wireless carrier sense multiple access (CSMA) systems are widely used but show extremely different transmission efficiency according to the operation environment. Simulation or prototype deployment is needed to see the transmission efficiency of a wireless CSMA system with the partial packet retransmission scheme. The lower bound for the transmission efficiency of such a system is found mathematically in this work. This shows how much the partial packet retransmission scheme improves the transmission efficiency quantitatively. It also shows that the maximum throughput is obtained at higher offered load compared to the conventional CSMA system without the partial packet transmission. The result of this work can be applied to IEEE 802.11 networks or wireless mesh networks.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.12
• /
• pp.6188-6204
• /
• 2017

Over the years, more password-based authentication key agreement schemes using chaotic maps were susceptible to attack by off-line password guess attack. This work approaches this problem by a new method--new theorem of chaotic maps: $T_{a+b}(X)+T_{a-b}(X)=2T_a(X)T_b(X)$,(a>b). In fact, this method can be used to design two-party, three-party, even in N-party intelligently. For the sake of brevity and readability, only a two-party instance: a novel Two-party Password-Authenticated Key Agreement Protocol is proposed for resisting password guess attack in this work. Compared with the related literatures recently, our proposed scheme can be not only own high efficiency and unique functionality, but is also robust to various attacks and achieves perfect forward secrecy. For capturing improved ratio of security and efficiency intuitively, the paper firstly proposes a new parameter called security/efficiency ratio(S/E Ratio). The higher the value of the S/E Ratio, the better it is. Finally, we give the security proof and the efficiency analysis of our proposed scheme.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.11 no.1
• /
• pp.103-122
• /
• 1993

A cause and counterplan of the increase in dark decay rate of$\varepsilon$-CuPc/PVCz photoreceptor which is consist of the carrier generation layer (CGL) of$\varepsilon$type copper phthalocyanine ($\varepsilon$-CuPc) thin film by an aqueous coating method and the carrier transport layer (CTL) of polyvinylcarbazol (PVCz) by spin coating, are studied in this paper. Electrochemical deposition of CGL was accompanied by an increase in work function of the aluminium substrate during the processes and the enhanced work function 5.3 eV rose above the ionization potential 5.16 eV of $\varepsilon$-CuPc. This resulted in the increased injection of holes from substrate into CGL and a fast dark decay rate. Improved photoreceptor, an electron-transport $\varepsilon$-CuPc/TNF photoreceptor, led to lowing of dark decay rate and increasing of photosensitivity. The carrier generation efficiency (ηg), carrier injection efficiency (ηi) and xerographic gain (G) of the $\varepsilon$-CuPc/TNF photoreceptor were obtained by XTOF method and PIDC.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.171-174
• /
• 1997

The great development of semiconductor industry demands the high efficiency and performance of related device, but the pick and place system of semiconductor packaging device can load a few units until nowdays. Although the system can load a lot of units, it can work multiple sort operation. The defect like that causes a low efficiency. Therefore, this paper represents the development of pick and place system which can work multiple sort operation.