• Journal of the Korean Wood Science and Technology
• /
• 제33권2호통권130호
• /
• pp.24-28
• /
• 2005

Monte Carlo simulation was performed on theoretical models of plywood warp for southern yellow pine plywood originating from the United States. The objective of the investigation was to determine which plywood layers was more warp sensitive to veneers that were manufactured to an undesired thickness. This study found that for a balanced panel (a panel of equal target thickness for each of five layers) manufactured veneers of undesired thickness would experience minimal warp. The veneers of undesired thickness placed in the center of the plywood panel also provided a minimum change of plywood warp properties. The panel warp was very sensitive to surface veneers constructed with undesired thickness. Conversely, this study confirms that monitoring of veneer thickness and proper allocations within the plywood lay-up were critical.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.141-148
• /
• 2013

The goal of this study was to find the optimum lamina size from red pine (Pinus densiflora) and Japanese cedar (Cryptomeria japonica) logs for the cross laminated timber (CLT) production. From visual inspection of the logs from two species, red pine log showed a larger knot and warp compared to the Japanese cedar. Different cross-sectional sizes of lamina ($110mm{\times}30mm$, $110mm{\times}40mm$, $110mm{\times}50mm$, $50mm{\times}30mm$, $30mm{\times}30mm$) from two species were analyzed for yield and grade. Regardless of the species, the optimized cross sectional size for maximizing the yield was $110mm{\times}30mm$. In grading for the different size laminas from Japanese cedar and red pine, a higher percentage of the first and second grade was found from the $110mm{\times}30mm$ lamina cut.

• Journal of the Korean Wood Science and Technology
• /
• 제41권1호
• /
• pp.42-50
• /
• 2013

1980년대 중반 이후 국내 생산이 시작된 온돌마루(이하 합판마루)는 종전의 주택용 바닥재(PVC 바닥재)의 대체재로서 일반 소비자들의 폭발적인 수요를 얻어왔다. 그러나 최근 마루판 산업은 건축경기 악화 및 산업 환경의 변화로 인한 수요의 감소와 그에 따른 생산율의 저하 등의 근본적인 문제점이 있다. 최근 마루판용 합판의 원재료로 주로 사용된 동남아산 수종의 고갈 및 변화로 인한 양질의 합판원재료 확보가 어려워졌다. 이에 대한 대응책으로 중국산 유칼립투스를 원재료로 부분적으로 이용한 마루판용 합판의 대체이용이 시도되고 있다. 본 연구에서는 유칼립투스 단판을 부심판으로 제조한 복합합판의 마루판용 합판의 원재료로서의 사용 가능성을 실험을 통해 비교분석하였으며, 모든 단판이 동남아산 Meranti로 구성된 합판을 대조군으로 설정했다. 변형에 영향을 미치는 인자로 단판 간 밀도차이와 합판의 밀도경사를 이용하였다. 본 연구의 실험결과는 다음과 같다. 1) 남양재 시험편은 병판의 밀도가 다른 단판의 밀도보다 큰 M자형의 밀도경사, 유칼립투스 시험편은 반대성향의 W자형의 밀도경사를 나타내었다. 2) 종류에 따른 마루판의 변형은 마루 가공 시험편이 합판상태로 가공을 한 경우보다 최소 0.1~최대 6.25 mm 적게 나타났으며, Density Profile 측정 결과 단판 간의 밀도차가 클수록 변형이 많이 발생하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제14권4호
• /
• pp.29-39
• /
• 1986

To investigate the effect of presurfacing, both 25mm rough and pre surfaced oak boards (Quercus grosseserrata BI.) were dried in the same dry kiln condition. Drying curves, drying strains and drying defects of rough and presurfaced boards were compared. The results obatained are as follows. 1. Average drying rate of rough and presurfaced boards from green to 10% M.C. was 0.276%/hr. and 0.284%/hr., respectively. 2. At the early stage of drying, in case of rough boards, maximum tensile strain of outer slices was $-24.2{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $13.0{\times}10^{-4}$mm/mm, and in case of pre surfaced boards, maximum tensile strain of outer slices was $-14.5{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $28.1{\times}10^{-4}$mm/mm. And in both cases, stress reversal occurred at about 40% M.C.. 3. Maximum surface checking appeared at about 40% M.C.. Of the 10 rough boards. 6 hoards contained surface checks, but presurfaced boards did not contained surface checks after drying. And the results of end checking were similar to those of surface checking. But, honeycomb was not found in both cases. 4. Board shrinkage. warp and casehardening of presurfaced boards were similar to those of rough boards. But, collapse of prsurfaced boards was less than that of rough boards.

• PNF and Movement
• /
• 제15권3호
• /
• pp.259-266
• /
• 2017

Purpose: This study aimed to compare muscle activities in the right leg during squatting on an angle-adjustable inclined wooden plate at three different angles. Methods: The subjects were 19 healthy adult men and women. An angle-adjustable inclined wooden plate was used for the experiment, and the subjects performed squatting at three adjusted angles of $0^{\circ}$ ankle angle, $10^{\circ}$ ankle flexion, and $10^{\circ}$ plantar flexion. Squatting was randomly performed without a sequence. The knee angle was set at $45^{\circ}$, and a goniometer was used to measure the angles accurately. Electromyography was employed to measure and compare muscle activity in the right leg in each condition. The measured data were converted to root mean square values to calculate the muscle activities. Results: This study showed no statistically significant difference at a $0^{\circ}$ ankle angle, but a statistically significant difference was found in the vastus medialis at $10^{\circ}$ of ankle flexion. Moreover, statistically significant differences were observed in the vastus medialis and lateralis at $10^{\circ}$ of plantar flexion. Conclusion: This study showed a statistically significant difference in the vastus medialis at $10^{\circ}$ of ankle flexion and statistically significant differences in the vastus medialis and lateralis at $10^{\circ}$ of plantar flexion. Therefore, it may be effective to perform squatting at $10^{\circ}$ of ankle flexion when intending to selectively strengthen the vastus medialis and at $10^{\circ}$ of plantar flexion when intending to strengthen both the vastus medialis and lateralis.