• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.12
• /
• pp.1329-1336
• /
• 2015

Due to the advances in hardware technologies for low-power CMOS cameras, there have been various researches on wireless video sensor network(WVSN) applications including agricultural monitoring and environmental tracking. In such a system, its core technologies include video compression and wireless transmission. Since data of video sensors are bigger than those of other sensors, it is particularly necessary to estimate precisely the traffic after video encoding. In this paper, we present an estimation method for the encoded video traffic in WVSN networks. To estimate traffic characteristics accurately, the proposed method first measures complexities of frames and then applies them to the bit rate estimation adaptively. It is shown by experimental results that the proposed method improves the estimation of bit rate characteristics by more than 12% as compared to the existing method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5A
• /
• pp.479-486
• /
• 2008

In this paper, an efficient training symbol design with m-sequence is proposed for the MIMO-OFDM based next generation wireless transmission system which supports gigabits per second data rate. In the traditional blute force method, the preamble design is based on the case by case comparison with the system requirements. This paper discusses a training symbol design methodology for the MIMO-OFDM system based on the m-sequence which has been widely used in the spread spectrum communication areas due to its good correlation characteristics. Also the step-by-step design and performance verification method within the limited search space is discussed. The proposed method targets the design of the training symbol which satisfies system requirements for the packet based MIMO-OFDM wireless communication system including automatic gain control(AGC), timing synchronization, frequency and sampling offset estimation, and MIMO channel estimation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.6A
• /
• pp.547-554
• /
• 2010

Recently, the multi-band orthogonal frequency division multiplexing(MB-OFDM) system, one of UWB system, can satisfy the requirement and can be applied to various wireless communication services because ultra-wideband(UWB) is a wireless communication technique that supports high data rate with low power. In this paper, the method applying Alamouti's space time block code(STBC) and cyclic delay diversity(CDD) is proposed. The proposed method can be easily applied with arbitrary number of relays and only needs two time slots of quasi stationary assumption. And it is applied to the MB-OFDM system. Second, an optimal relaying scheme based on decode-and-forward(DF) method is proposed which is provides good error performance compared to conventional schemes.

• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.39-47
• /
• 2012

Currently, most of the frequency spectrum resources are allocated and due to the lack of frequency, low frequency band, optimal for wireless communication environment is not used. Therefore, Cognitive Radio (CR) is a critical issue to solve the spectrum scarcity and to improve frequency spectrum utilization in wireless communication. In this paper, we implement data transmission and receive in a real CR system using the USRP(Universal Software Radio Peripheral) board and GNU Radio package of an open source development kit. Concretely, we detect the Primary User by spectrum sensing, and then we send Primary User information to the database. After receiving the information, because the database already sent optimal transmit power, bandwidth and channel information to CR equipment, CR can communicate without any interference to Primary User.

• KIPS Transactions on Computer and Communication Systems
• /
• v.4 no.12
• /
• pp.409-414
• /
• 2015

The energy conservation is the most important subject for long run operation of the sensor nodes with limited power resources. Clustering is one of most energy efficient technique to grouped the sensor nodes into distinct cluster. But, in a cluster based WSN, CHs and gateways bear an extra work load to send the processed data to the sink. The inappropriate cluster formation may cause gateways overloaded and may increase latency in communication. In this paper, we propose a novel load balanced clustering model for improving energy efficiency and giving a guarantee of long network lifetime. We show the result of performance measurement experiments that designs using a branch and bound algorithm and a multi-start local search algorithm to compare with the existing load balanced clustering model.

• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.811-816
• /
• 2011

In this paper, we analysis to consider the performance of PSPM (Phase Shift Pulse-position Modulation), the one of the low power communication technique, in near-field underwater sound channel by sea trial. PSPM is a QPSK(Quadrature Phase Shift Keying) modulation combined with PPM(Pulse Position Modulation) for low power communication in WBAN(Wireless Body Area Network). It is known that the bandwidth efficiency of PSPM is lower than conventional PSK but the power efficiency increases. In this paper, we will analyze the BER performance of PSPM using data acquired from the sea trials. The BER of QPSK was $6.04{\times}10^{-2}$, PSPM was $3.5{\times}10^{-1}$. Also, PSNR of QPSK was 9.37 dB and in case of PSPM was 9.11 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.3
• /
• pp.215-222
• /
• 2019

A frequency hopping(FH) signal can change its carrier frequency during transmission and has spread-spectrum characteristics in these frequency bands. Therefore, FH signals are widely used in applications that require low-probability-of-intercept(LPI) and anti-jamming (AJ) abilities in wireless communication environments. In this study, the authors propose a method for generating hopping information (HI), which includes start time, dwell time, and hopping frequency for unknown FH signals. The proposed blind HI generation method produces signal detection information based on the spectrum data and then extracts HI using operational procedures for estimating the target FH signal's status, such as appearance, maintenance, and termination. Further, simulation results demonstrate that the proposed method provides accurate HI without detection omissions for various FH signals.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.3
• /
• pp.27-35
• /
• 2011

Design of Sensor nodes in Wireless Sensor Network(WSN) should be considered some properties as electricity consumption, transmission speed, range, etc., and also be needed the protection against various attacks (e.g., eavesdropping, hacking, leakage of customer's secret data, and denial of services). The stream cipher Rabbit, selected for the final eSTREAM portfolio organized by EU ECRYPT and selected as algorithm in part of ISO/IEC 18033-4 Stream Ciphers on ISO Security Standardization recently, is a high speed stream cipher suitable for WSN. Since the stream cipher Rabbit was evaluated the complexity of side-channel analysis attack as 'Medium' in a theoretical approach, thus the method of power analysis attack to the stream cipher Rabbit and the verification of our method by practical experiments were described in this paper. We implemented the stream cipher Rabbit without countermeasures of power analysis attack on IEEE 802.15.4/ZigBee board with 8-bit RISC AVR microprocessor ATmega128L chip, and performed the experiments of power analysis based on difference of means and template using a Hamming weight model.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.1
• /
• pp.195-215
• /
• 2021

Multipath Transport Control Protocol (MPTCP) is a transport layer protocol that enables multiple TCP connections across various paths. Due to path heterogeneity, it incurs more energy in a multipath wireless network. Recent work presents a set of approaches described in the literature to support systems for energy consumption in terms of their performance, objectives and address issues based on their design goals. The existing solutions mainly focused on the primary system model but did not discourse the overall system performance. Therefore, this paper capitalized a novel stochastically multipath scheduling scheme for data and path capacity variations. The scheduling problem formulated over MPTCP as a stochastic optimization, whose objective is to maximize the average throughput, avoid network congestion, and makes the system more stable with greater energy efficiency. To design an online algorithm that solves the formulated problem over the time slots by considering its mindrift-plus penalty form. The proposed solution was examined under extensive simulations to evaluate the anticipated stochastic optimized MPTCP (so-MPTCP) outcome and compared it with the base MPTCP and the energy-efficient MPTCP (eMPTCP) protocols. Simulation results justify the proposed algorithm's credibility by achieving remarkable improvements, higher throughput, reduced energy costs, and lower-end to end delay.

• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.1
• /
• pp.27-35
• /
• 2022

In the most IPS (Indoor Positioning System), it is available to specify the user's movement by sending a specific signal from a tag such as a beacon to multiple receivers. This method is very efficiently used in places where the number of people is limited. On the other hand, in large commercial facilities, it is nearly difficult to apply the existing IPS method because it is necessary to attach a tag to each customer. In this paper, we propose a system that uses an external sensor grid to identify people's movement without using tags. Each sensor node uses both an ultrasonic sensor and an infrared sensor to monitor people's movements and sends collected data to the main server through wireless transmission for easy system maintenance. The operation was verified using the FPGA board, and we designed a VLSI circuit in 180nm process.