• 대한기계학회논문집
• /
• 제15권1호
• /
• pp.274-284
• /
• 1991

본 연구에서는 몇가지 단순한 스크린의 형상에 대하여 후류의 난류 특성치들 을 계측하여, 실제 현상을 파악하고 자료를 확보하여 앞으로의 연구에 활용하고자 하 였다.본 논문에서는 원형 스크린과 타원형 스크린을 기본 형상으로 택하여, 저항 계수를 변화시키면서, 후류유동장에서 평균속도 분포, 난류 운동에너지, 난류 전단응 력을 열선 풍속계로 계측하였다. 원형 스크린의 경우에는 주로 스크린의 모서리에서 발달하는 전단층의 확산과정을 연구하였고, 타원형 스크린의 경우에는 평균속도 분포 가 하류로 가면서 원형 후류로 발전되어가는 과정을 연구하였다.

• 콘크리트학회논문집
• /
• 제17권5호
• /
• pp.829-834
• /
• 2005

A series of reinforced G109 type specimens was fabricated and pended with a 15 weight percent NaCl solution. Mix design variables included 1) two cement alkalinities (equivalent alkalinities of 0.32 and 1.08), 2) w/c 0.50 and 3) two rebar surface conditions (as-received and wire-brushed). Potential and macro-cell current between top and bottom bars were monitored to determine corrosion initiation time. Once corrosion was initiated, the specimen was ultimately autopsied to perform visual inspection, and the procedure included determination of the number and size of air voids along the top half of the upper steel surface. This size determination was based upon a diameter measurement assuming the air voids to be half spheres or ellipse. The followings were reached based upon the visual inspection of G109 specimens that were autopsied to date. First, voids at the steel-concrete interface facilitated passive film breakdown and onset of localized corrosion. Based upon this, the initiation mechanism probably involved a concentration cell with contiguous concrete coated and bare steel serving as cathodes and anodes, respectively. Second, the corrosion tended to initiate at relatively large voids. Third, specimens with wire-brushed steel had a lower number of voids at the interface for both cement alkalinities, suggesting that air voids preferentially formed on the rough as-received surface compared to the smooth wire brushed one.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.1051-1060
• /
• 2001

Flow visualizations and hot-wire measurements on the inside flows of two different incubators are presented in this paper. An anatomically-correct neonate model was fabricated using the rapid prototyping machine, based on the 3-D scanned data. The result showed that air flow in the incubator was affected not only by the air circulation system but also by the design of incubator chamber. Large rotating motions were located around the corners of free space. A number of small eddies were found in regions of high shear flow, in areas such as that between the air inlet and the neonate. But, these small eddies were found to be stationary at that locations. Those small eddies might interfere with convective and evaporative heat transfers from the neonate. This study has led to a better understanding of flow mechanism in an incubator chamber and provided the guidance needed for the advancement of improved computational fluid dynamic models.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.96-101
• /
• 1986

본 연구에서는 2차원 충돌분류에 있어서 전열면상에 비교적 큰 스케일을 가진 트랜스버스 리브(transverserib)형의 피형돌기를 만들고 충돌영역을 포함하여 통상열전달율이 현저하게 낮아지는 하류역까지의 넓은 영역에 걸쳐 전달회진을 목적 으로 전달특성을 실험적으로 조사하고 전보에서 다룬 거형의 트랜스버스 리브를 갖는 전열면에서의 결과와 비교 검토하였다. 한편 돌기면상의 유동형태의 상세를 smoke wire법에 의해 충돌분류 특유의 종과류와 그 신장에 대하여 조사하고 표면부유법 (surface floating method)에 의해 비교적 큰 스케일의 돌기에 따른 흐름의 박이 및 재부착에 관해서 조사하여 이들과 전열기구와의 관계를 정성적으로 검토하였다.

• 대한기계학회논문집A
• /
• 제28권8호
• /
• pp.1237-1244
• /
• 2004

The orthodontic surgery including lingual orthodontics has recently attracted a person's attention due to its functional and esthetic appreciation. The skeletal anchorage with the miniscrew is newly adopted in the lingual orthodontics to assist the upholding ability. The appliciation needs to understand the mechanism of the orthodontic appliance and its related orthodontic correction for optimal orthodontic treatment. There is, however, few information about the qualitative and quantitative effect of the orthodontic appliance with the miniscrew has not been well identified. In this paper, three dimensional finite element analysis is introduced to the lingual orthodontics in order to investigate the effect of the anterior retraction force on the miniscrew and transpalatal arch wire. The analysis determines the adequate location of the miniscrew and the point of force application of the anchorage system in the lingual orthodontics. The analysis results demonstrate the effect of the position of the miniscrew and the transpalatal arch wire on the lingual orthodontics.

• Current Photovoltaic Research
• /
• 제1권1호
• /
• pp.27-32
• /
• 2013

We investigated the growth mechanism of amorphous-phase Si thin films in order to improve the film characteristics and circumvent photo-degradation effects by implementation of hot-wire chemical vapor deposition. Amorphous silicon thin films grown in a silane/hydrogen mixture can be decomposed by a resistive heat filament. The structural properties were observed by Raman spectroscopy, FTIR, SEM, and TEM. The electrical properties of the films were measured by photo-conductivity, dark-conductivity, and photo-sensitivity. The contents of Si-H and $Si-H_n$ bonds were measured to be 19.79 and 9.96% respectively, at a hydrogen flow rate of 5.5 sccm, respectively. The thin film has photo-sensitivity of $2.2{\times}10^5$ without a crystalline volume fraction. The catalyst behavior of the hot-wire to decompose the chemical precursors by an electron tunneling effect depends strongly on the hydrogen mixture rate and an amorphous Si thin film is formed from atomic relaxation.

• 전기학회논문지
• /
• 제63권2호
• /
• pp.272-276
• /
• 2014

In this paper, cable drive mechanism is proposed to implement high reduction gear ratio. Cable drive mechanism has great advantages such as light weight, high degree of freedom about design aspect and zero backlashes. However, it is restrictively utilized for robotic applications because it is difficult to implement high reduction gear ratio more than 10 to 1. Proposed mechanism enables multi-level reductions by adopting seamless winding method (SWM) which links the previous output axis and the next input axis. Consequently, this reduces the mechanical complexity significantly and enables high reduction with only one single wire cable. 3D CAD design was provided and prototype was manufactured.

• 제어로봇시스템학회논문지
• /
• 제15권8호
• /
• pp.798-803
• /
• 2009

This paper proposes a grating scanner which is driven by a stack-type piezoelectric element. The mechanism of the grating scanner is based on flexure hinges. Using some constraints, the compliant mechanism is designed and then verified by Finite Element Analysis. The designed compliant mechanism is manufactured by wire electro-discharge machining, and then integrated with a stack-type piezoelectric element for actuation and a capacitance displacement sensor for measuring ultra-precision displacement. Experiments demonstrates the characteristics and the performances of the grating scanner using the terms of working range, resonance frequency, bandwidth and resolution. The grating scanner is applicable to a Moire interferometry for measuring 3-dimensional microscopic surface.

• 한국생산제조학회지
• /
• 제26권2호
• /
• pp.257-261
• /
• 2017

Drilling file is medical mini-drill which is made of Ni-Ti material and has tapered shape. It's for removing teeth nervine which helps the endodontic treatment. All files, saled at domestic market, are imported from U.S. and Europe. Also they have low manufacturing efficiency and high price because it is made by universal 5 axis CNC grinding machine. To solve these problem, 3 axis CNC table, controllable tilting angle spindle and helix angle moving table are devised. To confirm divised CNC grinding machine's manufacturing accuracy, conveying amount and finish product size measurement expreiment has been practiced. Also to automate all manufacturing processes, automatic mechanism is designed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권6호
• /
• pp.736-744
• /
• 2003

This study is conducted to investigate aerodynamic forces and wake structures about the pressure interference of a circular cylinder with slits. An experimental investigation of a circular cylinder with slits is carried out in uniform flow in the range of Reynolds number from 8,000 to 32,000 using X-type hot wire. Flow visualization is executed by smoke-wire method to understand the mechanism of these vortex formation process. Inspection in the wake at X/D=5.5 of the cylinder with the slits suggested that a strong vortex-shedding pattern for these cylinders is revealed compare with a circular cylinder without slits. It is found that the rolling up position of shear layer of the cylinder with slits is shorten compare with a circular cylinder without slits.