• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.6
• /
• pp.732-742
• /
• 1985

Measurements of mean velocity and turbulence characteristics are obtained with a linearized constant temperature hot-wire anemometer in a two-dimensional turbulent jet discharging parallel to a flate. Wall static pressure distribution is also measure. The Reynolds number based on the jet nozzle width (D) is about 42,000 and the step height is 2.5D. The reattachment length is found to be 7.5D by using both wool tuft and oil methods. Upstream of the reattachment point, there exist double coherent structures and mean velocity, Reynolds stresses and triple product profiles are asymmetric about jet center line due to the influence of streamline curvature and recirculating flow region. Near the reattachment point, wall static pressure and turbulence quantities change its shape rapidly because of the large eddies by the solid wall. Especially, turbulence intensity has a maximum value in the reattachment regin, then decreases slowly in the redeveloping wall jet ragion. Downstream of X/D=14, a single large scale eddy structure is formed. Far downstream affer the reattachment(X/D.geq.18) mean velocity profile, the decay of maximum velocity and the variation of jet half width are nearly similar to those of plane wall jet, but the Reynolds stresses are higher than those of the latter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.2
• /
• pp.107-113
• /
• 2008

In 22.9[kV]-y distribution systems, underground cables are provided with multiple-point ground in which each coaxial-neutral line of the distribution cable lines(A, B, C phases) is 3-wire common grounded. In the underground cable distribution systems, circulating current flows in the coaxial-neutral lines and its magnitude amounts to about $40{\sim}50[%]$ load currents, even though loads are balanced. Power loss due to the circulating current consequently reaches to about 76[%] total losses occurred in all conductor lines. This power loss provokes additional temperature rise of the underground cable lines and finally results in 20[%] reduction of the current capacity of the cables. This paper presents a new ground method to overcome such a problem. The proposed method eliminates the circulating current flowing in the coaxial-neutral line effectively. Measurement results confirmed from the practical site-test show validity and effectiveness of this research.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.10
• /
• pp.23-30
• /
• 1999

We experimented on the sub 50nm patterning using E-beam lithography system. SAL601 negative E-beam resist was used for this experiment. In order to utilize the maximum ability of E-beam system, firstly, we reduced the PR thickness to 100nm, and the field size to 200 ${um}m$. Then PEB (Post Expose Bake) time/temperature, which is one of the very important factors when SAL601 is used, were reduced for minimum line width. In addition, digitizing is optimized for better results. Quantum wire and quantum dot which can be used for nanoscale memory device, such as single electron memory device, are fabricated using these developed lithography techniques.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.3-6
• /
• 2015

Recently, the collection of the sensor data and its analysis become important as the smart buildings equipped with the various sensors appear as a usual scene. The interconnection through the wire cable among the sensors is indispensible because of the information collections such as the temperature, the humidity, and the luminance in the rooms and the hallways for the effective management of the in-building energies. However, these interconnections through the cabling will be very costly, time-consuming, and a difficult task since they will cause some damages to the buildings. Therefore, the interconnections through the unwired connections are required in terms of the deployment effectiveness such as time and cost In this paper, the design and the operation appropriateness are confirmed through the simulation of the signal measurement system for in-building propagation characteristics based on signature sequence and the analysis of the collected measurement data is performed thereafter.

• Progress in Superconductivity and Cryogenics
• /
• v.17 no.3
• /
• pp.37-40
• /
• 2015

Recently, the electrical insulation design for electrical apparatuses is important to cope with the tendency of high voltage. The degradation characteristics of a superconducting coil due to an electrical breakdown should be considered to design a high voltage superconducting coil. In this paper, the degradation characteristics of 2G high temperature superconducting (HTS) wires are studied with respect to electrical breakdown tests. To analyze the dependency of the degradation characteristics of 2G HTS wires, the electrical breakdown tests are performed with AC(alternating current) and DC(direct current) voltage. All tests are performed by applying various magnitudes of AC and DC breakdown voltages. To verify the degradation characteristics of 2G HTS wires, the tests are performed with various 2G HTS wires with respect to stabilizer materials. The degradation characteristics of 2G HTS wires, such as Ic(critical current) and index number are measured by performing electrical breakdown tests. It is found that the characteristics such as Ic and index number can be degraded by an electrical breakdown. Moreover, it is concluded that the degradation characteristics of 2G HTS wires are affected by the stabilizer material and applied voltages. The cross-sectional view of 2G HTS wires is observed by using a scanning electron microscope (SEM). As results, it is found that the degradation characteristics of 2G HTS wires are concerned with hardness and electrical conductivity of stabilizer layers.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.6
• /
• pp.72-78
• /
• 1998

An optical modulator Ti:LiNbO$_3$optical waveguide and CPW electrode structure were fabricated. The optical modulator was packaged using components such as ferrules, dirmy LN block and glass, vibration and shock absorbption pad, and alumina feeder through processings of pigtailing. Au wire bonding, epoxing, SMA connecting, sealing. The electrical and optical characteristics were measured after packaging. The electrical properties of S$_{21}$ and S$_{11}$ were obtained as 9.8 GHz at -3 dB and -8.9dB at 14.4GHz, respectively. Optical waveguide prepared met requirements for a single mode at a 1550nm wavelength range. Insertion loss was 4.3dB at room temperature after packaging, and was varied 4.3~6.4dB at various temperatures, 5~45$^{\circ}C$. E-O bandwidth measurement showed 3dB optical response at 7.8GHz, which means that it is applicable for 10Gbps optical communicationon

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.876-891
• /
• 1988

This study was carried out to investigate the mixing flow of a turbulent cross jet in a cylindrical chamber. A study on the turbulent mixing flow of a cross jet at 45.deg. with respect to each other in the free atmospheric condition was conducted before this study and has given us some fundamental experimental results. Present data have been analyzed and compared with semi-empirical equations for a round and a plane jets. Interests on this kind of cross jets (flows) have been increasing during the past several years for the purpose of the analysis of mixing flows and their applications. In this study, a turbulent cross jet of air in a cylindrical chamber has been conducted and the turbulent characteristics in the mixing region have been analyzed experimentally. The experimental data were discussed by comparing with the semi-empirical equations of Hinze and Gortler. From the experimental curve, the semi-empirical equations of mean velocities and Reynolds stresses have been derived. Three dimensional data acquisitions and the statistical treatments of turbulence characteristics were carried out by on-line computer measurement system connected with the constant temperature type 2-channel hot-wire anemometer system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.799-803
• /
• 2001

Miniature heat pipe(MHP) with woven-wired wick was used to cool the CPU of a notebook PC. The pipe with circular cross-section was pressed and bent for packaging the MHP into a notebook PC with very limited compact packaging space. A cross-sectional area of the pipe is reduced about 30% as the MHP with 4mm diameter is pressed to 2mm thickness. In the present study a performance test has been performed in order to review varying of operating performance according to pressed thickness variation and heat dissipation capacity of MHP cooling module that is packaged on a notebook PC. New wick type was considered for overcoming low heat transfer limit when MHP is pressed to thin-plate. The limiting thickness or pressing is shown to be within the range of 2mm∼2.5mm through the performance test with varying the pressing thickness. When the wall thickness of 0.4mm is reduced to 0.25mm for minimizing conductive thermal resistance through the wall of heat pipe, heat transfer limit and thermal resistance of MHP were improved about 10%. In the meantime, it is shown that the thermal resistance and heat transfer limit for the MHP with central wick type are higher than those of MHP with existing wick types. The results of performance test for MHP cooling modules with woven-wired wick to cool a notebook PC shows the stability as cooling system since T(sub)j(Temperature of Processor Junction) satisfy a demand condition of 0∼100$\^{C}$ under 11.5W of CPU heat.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.114-119
• /
• 1996

The use of holographic interference lithography and removal techniques to corrugate GaAs substrate have been studied. The periodic photoresist structure, which serves as a protective mask during etching, is holographically prepared. Subsequently periodic V-grooved pattern is formed on the GaAs substrate by conventional a H$_{2}$SO$_{4}$-H$_{2}$O$_{2}$-H$_{2}$O wet etching. The linewidth of a GaAs pattern is about 0.4$\mu$m and the depth is 0.5$\mu$m A quantum wires(QWRs) array is well formed on the V-grooved substrate by MOCVD (metalorganic chemical vapor deposition) growth of GaAs/Al$_{0.5}$Ga$_{0.5}$As (50$\AA$/300$\AA$) quantum wells. The formation of QWR array is confirmed by the temperature dependent photoluminescence (PL) measurement. The intensive PL peak with a FWHM of 6meV at 21K shows the high quality of the QWR array.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.53-57
• /
• 1992

We report the crystal growth and the electro-optic characteristics of $CdS_{1-x}Se_{x}$ thin films. $CdS_{1-x}Se_{x}$ thin films wire deposited on the alumina plate by electron beam evaporation technique in pressure of $1.5{\times}10^{-7}$ torr, voltage of 4kV, current of 2.5mA and substrate temperature of $300^{\circ}C$. The deposited $CdS_{1-x}Se_{x}$ thin films were proved to be a polycrystal with hexagonal structure through X-ray diffraction patterns. $CdS_{1-x}Se_{x}$ photoconductive films showed high photoconductivity after annealing at $550^{\circ}C$ for 30 minutes. And the films have been investigated the Hall effect, photocurrent spectra, sensitivity, maximum allowable power dissipation and response time.