• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.1
• /
• pp.1-12
• /
• 2009

Wing-in-Ground vehicles and aerodynamically assisted boats take advantage of increased lift and reduced drag of wing sections in the ground proximity. At relatively low speeds or heavy payloads of these craft, a flap at the wing trailing-edge can be applied to boost the aerodynamic lift. The influence of a flap on the two-dimensional NACA 4412 airfoil in viscous ground-effect flow is numerically investigated in this study. The computational method consists of a steady-state, incompressible, finite volume method utilizing the Spalart-Allmaras turbulence model. Grid generation and solution of the Navier-Stokes equations are completed using computer program Fluent. The code is validated against published experimental and numerical results of unbounded flow with a flap, as well as ground-effect motion without a flap. Aerodynamic forces are calculated, and the effects of angle of attack, Reynolds number, ground height, and flap deflection are presented for a split and plain flap. Changes in the flow introduced with the flap addition are also discussed. Overall, the use of a flap on wings with small attack angles is found to be beneficial for small flap deflections up to 5% of the chord, where the contribution of lift augmentation exceeds the drag increase, yielding an augmented lift-to-drag ratio.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.931-939
• /
• 2013

In this paper, we try to find the lifting-line method which is applicable to the conceptual design of aircraft wings, and analyze the accuracy and coverage of the method. Two methods that are extended from the lifting-line theory of Prandtl are selected. One of the methods is Weissinger's method which imposes the velocity boundary condition at the control points located at the quarter chord, and the other is Phillips's method which combines the three-dimensional vortex lifting law. Calculations are performed for an elliptic wing, a swept back wing, and a tapered unswept wing with dihedral angle and geometric twist. The aerodynamic data of the potential flow such as spanwise distributions of circulation and downwash, lift and induced drag are obtained through calculations, and these data are compared with theoretical results and wind tunnel test data. As a result, Weissinger's method showed good accuracy and reliability regardless of wing shapes, but Phillips's method revealed inaccurate results for a swept back wing.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.1
• /
• pp.84-93
• /
• 1994

The purpose of present study is to investigate the surface roughness on tip-vortex cavitation and its induced noise, emanating from an elliptic wing of NACA 0012 section. Roughness elements of $200{\mu}m$ are applied to the 10% portion of wing tip, and then, the wing tip as well as the leading edge. It is shown from cavitation observation that the cavitation inception is first visible at about half chord downstream of wing tip for most experimental conditions, and developed into the tip-vortex cavitation and finally the fully developed cavitation as cavitation number is decreased. Acoustic noise generated by a tip-vortex cavitation has its frequency range of 3 kHz to 50 kHz, while the fully-developed cavitation at lower cavitation number induces a broad band spectrum. It is also shown that, when the roughness elements are applied to the wing tip and the leading edge, the cavitation characteristics and its induced noise are improved. Moreover, it is appeared that the condition at which the rough surface is at pressure side gives a better result. although its lift-drag ratio is reduced.

• Smart Structures and Systems
• /
• v.15 no.6
• /
• pp.1393-1410
• /
• 2015

An original sensor system based on Fiber Bragg Gratings (FBG) for the strain monitoring of an adaptive wing element is presented in this paper. One of the main aims of the SARISTU project is in fact to measure the shape of a deformable wing for performance optimization. In detail, an Adaptive Trailing Edge (ATE) is monitored chord- and span-wise in order to estimate the deviation between the actual and the desired shape and, then, to allow attaining a prediction of the real aerodynamic behavior with respect to the expected one. The integration of a sensor system is not trivial: it has to fit inside the available room and to comply with the primary issue of the FBG protection. Moreover, dealing with morphing structures, large deformations are expected and a certain modulation is necessary to keep the measured strain inside the permissible measure range. In what follows, the mathematical model of an original FBG-based structural sensor system is presented, designed to evaluate the chord-wise strain of an Adaptive Trailing Edge device. Numerical and experimental results are compared, using a proof-of-concept setup. Further investigations aimed at improving the sensor capabilities, were finally addressed. The elasticity of the sensor structure was exploited to enlarge both the measurement and the linearity range. An optimisation process was then implemented to find out an optimal thickness distribution of the sensor system in order to alleviate the strain level within the referred component.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.530-536
• /
• 2010

In-flight icing is a critical technical issue for aircraft safety and, in particular, ice accretions on aircraft surfaces can drastically impair aerodynamic performances and control authority. In order to investigate icing effects on the aerodynamic characteristics of KC-100 aircraft, a state-of-the-art CFD code, FENSAP-ICE, was used. A main wing section and full configuration of KC-100 aircraft were considered for the icing analysis. Also, shapes of iced area were calculated for the design of anti-/de-icing devices. The iced areas around leading edge of main wing and horizontal tail wing were observed maximum 7.07% and 11.2% of the chord length of wing section, respectively. In case of wind shield, 16.7% of its area turned out to be covered by ice. The lift of KC-100 aircraft were decreased to 64.3%, while the drag was increased to 55.2%.

• Journal of Aerospace System Engineering
• /
• v.10 no.1
• /
• pp.59-65
• /
• 2016

Korea Aerospace Research Institute (KARI) is developing an electric-driven HALE UAV in order to secure system and operational technologies since 2010. Based on the 5 years of flight tests and design experiences of the previously developed electric-driven UAVs, KARI has designed EAV-3, a solar-powered HALE UAV. EAV-3 weighs 53 kg, the structure weight is 21 kg, and features a flexible wing of 19.5 m in span with the aspect ratio of 17.4. Designing the main wing and empennage of the EAV-3 the amount of the bending due to the flexible wing, 404 mm at 1-G flight condition based on T-800 composite material, and side wind effects due to low cruise speed, V_cr = 6 m/sec, are carefully considered. Also, unlike the general aircraft there is no center of gravity shift during the flight. Thus, the static margin cuts down to 28.4% and center of gravity moves back to 31% of the Mean Aerodynamic Chord (MAC) comparing to the previously developed scale-down HALE UAVs, EAV-2 and EAV-2H, to minimize a trim drag and enhance a performance of the EAV-3. The first flight of the EAV-3 has successfully conducted on the July 29, 2015 and the test flight above the altitude 14 km has efficiently achieved on the August 5, 2015 at the Goheung aviation center.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.1-8
• /
• 2002

The effects of sideslip on the vortex over a delta wing was investigated experimentallu at a free strean velocity of 40 m/sec, corresponding to a Reynolds number of 1.76$\times$$10^6$, based on the root chord. The angles of attack ranged from $16{^{\circ}}$ to $28{^{\circ}}$, and the sideslip angles treated were $0{^{\circ}}$, $-10{^{\circ}}$, and $-20{^{\circ}}$. It was observed that the sideslip decreased the strengths of the vortices of both windward and leeward sides of the wing, and promoted the vortex breakdown on the windward side. At sideslip angle of $-10{^{\circ}}$, the vortex strength of leeward side was increased as the angle of attack increased. This asymmetric development and breakdown of vortices in sideslip condition would cause an abrubt change of the rolling moment at a high angle of of attack, which could be considered as a rolling moment instability.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.43-50
• /
• 2009

In order to reduce the download around Smart UAV(SUAV) at hovering and transition mode, flow control using synthetic jet has been performed. Many of the complex tilt rotor flow features are captured including wing leading and trailing edge separation, and the large region of separated flow beneath the wing. First, in order to control the trailing edge separation, synthetic jet is located at 30, 95% of flap chord length. The flow control using synthetic jet on flap shows that stall characteristics depending on several mode can be improved through separation vortices resizing. Also, a flap jet and a 0.01c jet which control the separation efficiently are applied at the same time at each test case because controlling the leading edge separation is essential for download reduction. As a result, time averaged download is reduced about 18% comparing with no control case at hovering mode and 48% at transition mode. These research results show that if flow control using leading edge jet and trailing edge jet is used effectively to the SUAV in overall flight mode, flight performance and stability can be improved.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.43-46
• /
• 2008

Quad-Rotor, which consists of four blades, performs a flight task by controling each rotation speed of the four blades. Quad-Rotor blade making no use of cyclic pitch or collective one is a type of fixed-wing as different from helicopter blade. Although, Quad-Rotor is simple and easy to control for those reasons, blade configuration of the fixed wing is one of the critical factors in determining the performance of Quad-Rotor. In the present study, coefficients for thrust and power of Quad-Rotor blade were derived from the data acquired by using 6-component balances. Firstly, Measurements for aerodynamic force were conducted at various pitch angles (i.e., from 0$^{\circ}$ to 90$^{\circ}$ with the interval of 10$^{\circ}$). The blade used in this experiment has aspect ratio of 6 and chord length of 35.5 mm. Secondly, assembled-blade, which was an integral blade but divided into many pieces, was used in order to test aerodynamic forces along twist angles. The curve of thrust coefficient along pitch angle indicates a parabola form. Stall which occurs during wind tunnel test to calculate lift coefficient of airfoil does not generate. When deciding the blade twist angle, structural stability of blade should be considered together with coefficients of thrust and power. Those aerodynamic force data based on experimental study will be provided as a firm basis for the design of brand-new Quad-Rotor blade.

• Journal of the Korean Society of Visualization
• /
• v.18 no.3
• /
• pp.69-76
• /
• 2020

In the present study, we investigate the flow separation characteristics of a paraglider canopy model by tuft visualization. The experiment is conducted at Re = 3.3×105 in a wind tunnel large enough to contain the three-dimensional paraglider canopy model, where Re is Reynolds number based on the mean chord length and the free-stream velocity. The flow separation characteristics of the canopy model near the wing root are similar to those of a two-dimensional airfoil with a cross-section similar to the model. On the other hand, near the wingtip region, the flow separation is suppressed by the downwash induced by the wingtip vortex. As a result, as the angle of attack increases, the flow separation occurs from the wing root region of the canopy model and develops toward the wingtip.