• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.2
• /
• pp.46-55
• /
• 2005

A rocket-powered vehicle is designed conceptually which uses an engine running on methane and oxygen and delivering 10 tons of thrust. The aerodynamic coefficients of the vehicle are taken to be those of the Japan's HOPE-X, and the weight of this vehicle is estimated using a method developed by NASA. The resulting vehicle will be about 9 meters long, 5.8 meters in wing span, weigh about 2 tons empty, carry a maximum of 5.6 tons of propellant, and endure a g-load of 4.5. The craft will be able to carry five passengers, in addition to a pilot, and fly for space tourism between a northern and a southern airport with a maximum g-load varying from 3g to 4g depending on the route flown.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.2
• /
• pp.259-269
• /
• 2015

The issue of the longitudinal stability of a WIG vehicle has been a very critical design factor since the first experimental WIG vehicle has been built. A series of studies had been performed and focused on the longitudinal stability analysis. However, most studies focused on the longitudinal stability of WIG vehicle in cruise phase, and less is available on the longitudinal static stability requirement of WIG vehicle when hydrodynamics are considered: WIG vehicle usually take off from water. The present work focuses on stability requirement for longitudinal motion from taking off to landing. The model of dynamics for a WIG vehicle was developed taking into account the aerodynamic, hydrostatic and hydrodynamic forces, and then was analyzed. Following with the longitudinal static stability analysis, effect of hydrofoil was discussed. Locations of CG, aerodynamic center in pitch, aerodynamic center in height and hydrodynamic center in heave were illustrated for a stabilized WIG vehicle. The present work will further improve the longitudinal static stability theory for WIG vehicle.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.11
• /
• pp.864-872
• /
• 2002

In this study, the effect of planform curvature on the stability of coupled flow/structure vibration is examined in transonic and supersonic flow regions. The aeroelastic analysis for the frequency and time domain is performed to obtain the flutter solution. The doublet lattice method(DLM) in subsonic flow is used to calculate unsteady aerodynamics in the frequency domain. For all speed range, the time domain nonlinear unsteady transonic small disturbance code has been incorporated into the coupled-time integration aeroelastic analysis (CTIA). Two curved wings with experimental data have been considered in this paper MSC/NASTRAN is used for natural free vibration analyses of wing models. Predicted flutter dynamic pressures and frequencies are compared with experimental data in subsonic and transonic flow regions.

• Journal of Wind Energy
• /
• v.5 no.1
• /
• pp.33-42
• /
• 2014

The new aerofoil, KA2 was designed to apply to the wind turbine blade. For the aerofoil, numerical analysis was performed to review aerodynamic characteristics like lift and drag coefficient. And they are verified with test data using the digital wind tunnel and test samples from 3D printer. The digital wind tunnel was developed to test wing in the small laboratory, and verified with test of NACA0012 airfoil. KA2 aerofoil is asymmetric, and has the thickness ratio of 14%, and 12 degree of AOA at the maximum lift coefficient of 1.3. In this paper, aerodynamic characteristics from numerical and test approaches will be proposed with AOA in detail. Therefore, this aerofoil will be used for the design of wind turbine blade.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1039-1048
• /
• 2008

new computational procedure for the Non-Linear Vortex Lattice Method (NLVLM) is suggested in this work. Conventional procedures suggested so far usually involves inner iteration loop to update free vortex shape and an under-relaxation based iteration loop to determine the free vortex shape. In this present work, we suggest a new formula based on quasi-steady concept to fix free vortex shape which eliminates the need for inner iteration loop. Further, the ensemble averaging of the induced velocities for a given free vortex segment evaluated at each iteration significantly improves the convergence property of the algorithm without resorting to the under-relaxation technique. Numerical experiments over several low aspect ratio wings are carried out to obtain optimal empirical parameters such as the length of the free vortex segment, the vortex core radius, and the rolled-up wake length.

• Journal of Advanced Navigation Technology
• /
• v.21 no.5
• /
• pp.450-458
• /
• 2017

This paper presents dynamic modelling and simulation study on attitude/altitude control of an insect-mimicking flapping micro aerial vehicle during hovering. Mathematical modelling consists of three parts: simplified flapping kinematics, flapping-wing aerodynamics, and six degree of freedom dynamics. Attitude stabilization is accomplished through linear quadratic regulator based on the linearized model of the time-varying nonlinear system, and altitude control is designed in the outer loop using PID control. The performance of the proposed controller is verified through numerical simulation where attitude stabilization and altitude control is done for hovering. In addition, it is confirmed that the attitude channel by periodic control is marginally stable against periodic pitching moment caused by flapping.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2005

Civil aviation regulation such as FAR and loads analysis procedure based on this was explained, and loads analysis procedure and results for Smart UAV was presented for application case. For loads analysis, applicable regulations and loads conditions should be prepared in advance, and modeling for aerodynamics, weight, and structure should be performed. Panel method is usually adopted for aircraft loads analysis to obtain aerodynamic loads. In this study, ARGON which is multidisciplinary fixed wing aircraft design software co-developed by KARI and TsAGI was used for loads analysis. ARGON can be utilized for flutter and stress analysis as well as for flight and ground loads analysis. In this paper, flight loads analysis of 4-seater canard airplane was performed with ARGON and that results were presented.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.58-65
• /
• 2014

The adaptive wavelet method is studied for the enhancement of computational efficiency of three-dimensional flows. For implementation of the method for three-dimensional Euler equation, wavelet decomposition process is introduced based on the previous two-dimensional adaptive wavelet method. The order of numerical accuracy of an original solver is preserved by applying modified thresholding value. In order to assess the efficiency of the proposed algorithm, the method is applied to the computation of flow field around ONERA-M6 wing in transonic regime with 4th and 6th order interpolating polynomial respectively. Through the application, it is confirmed that the three-dimensional adaptive wavelet method can reduce the computational time while conserving the numerical accuracy of an original solver.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.04a
• /
• pp.120-124
• /
• 2007

Helicopters and rotary-wing vehicles encounter a wide variety of complex aerodynamic phenomena and these phenomena present substantial challenges for computational fluid dynamics(CFD) models. This investigation presents the rotor aerodynamic analysis items for the helicopter development and variety aerodynamic analysis methods to provide the better solution to researchers and helicopter developers between aerodynamic problems and numerical aerodynamic analysis methods. The numerical methods to make an analysis of helicopter rotor are as below - CFD Modelling : actuator disk model, BET model, fully rotor model,... - Grid : sliding mesh, chimera mesh / structure mesh, unstructure mesh,... - etc. : panel method periodic boundary, quasi-steady simulation, incompressible,... The choice of CFD methodology and the numerical resolution for the overall problem have been driven mostly by available computer speed and memory at any point in time. The combination of the knowledge of aerodynamic analysis items, available computing power and choice of CFD methods now allows the solution of a number of important rotorcraft aerodynamics design problems.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.473-473
• /
• 2009

There have been many academic researches on the aerodynamic design of wind turbine based on blade element method (BEM) and momentum theory (MT, or actuating disk theory). However, in the real world, the turbine blade design requires many additional constraints more than theoretical analysis. The standard procedure is studied in the present paper to design new blades for the wind turbine system ranged from the small size from 1 to 10 kW. From the experience of full design of a 10 kW blade, the authors tried to set up a standard procedure for the aerodynamic design based on IEC 61400-2. Wind-turbine scale, rotating speed, and geometrical chord/twist distribution at the segmented span positions are calculated with a suitable BEM/MT code, and the geometrical shape of tip and root should be modified after considering various parameters: wing-tip vortex, aerodynamic noise, turbine efficiency, structural safety, convenience of fabrication, and even economic factor likes price, etc. The evaluated data is passed to the next procedure of structural design, but some of them should still be corresponded with each other: the fluid-structure interaction is one of those problems not yet solved, for example. Consequently, the design procedure of small wind-turbine blades is set up for the mass production of commercial products in this research.