• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.598-605
• /
• 2003

The optimized conditions for the cross-sectional TEM sample preparation using tripod polisher and ion-beam miller was confirmed by AFM and TEM. For the TEM observation of interfaces including InGaN layers like InGaN/GaN MQW structures, the sample preparation by the only tripod polishing was useful due to the reduction of artifacts. On the other hand, in case of the thick nitride films like ELO, PE, and superlattice, both tripod polishing and controlled ion-beam milling were required to improve the reproducibility. As a result, the ion-beam milling with the $60^{\circ}$modulation showed the minimum height difference between film and sapphire interface and the ion-beam milling of the $80^{\circ}$modulation showed the broad observable width.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.93-97
• /
• 1988

The sliding mode control is an effective method to establish robustness against parameter variations and disturbance. But, in sliding mode strategy, the control function is discontinuous on the hyperplane. Consequently, the control input chatters at high frequency. When we apply such a control to the induction motor drive system, that causes a torque ripple and current harmonics, which are harmful to the system. In this paper, we introduce a low pass filter between sliding mode control output and driver input to overcome that problem. The band-width of this filter is varied according to the error funtion to improve transient responses.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1960-1962
• /
• 1998

Reference/modulating waveform continuity is not a necessary condition for the implementation of switching patterns for three-phase pulse-width modulated(PWM) converters. This is based on the fact that the converter phase-voltages do not need to be sinusoidal and switching pattern discontinuities do not degrade the quality of output/input voltage/current waveforms by introducing low-order harmonics if certain parameters are optimized. This paper introduces the selected harmonic elimination to reduce the switching frequency and low-order harmonics compared with continuous PWM techniques and some discontinues switching patterns for PWM converter.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.95-102
• /
• 2007

The practice of business estimate flood discharge by rainfall-flow relation that is easy collection of observation data. The important factor is rainfall, coefficient of runoff, and drainage area for analysis of runoff-flow relation. The practice of business usually use probability rainfall that use a weighted average value after each observation post estimate probability of non-same time. It has more error than same time probability rainfall, and it can excess of estimation because it can't consider space distribution of rainfall. The study of result showed similar aspect with existing ARF but width of coefficient become smaller. And the comparison of peak flow did not different what used by ARF and same time probability rainfall(A group). But non-same time probability rainfall is bigger 25% more than another(B group). Between A group and B group of the difference increased with the lapse of time.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.1
• /
• pp.97-103
• /
• 2011

With the aim to increase blade loadings and stable operating range in highly loaded compressors, this article has been conducted to explore, through a numerical parametric study, the potential of passive control using slotted bladings in cascade configurations. The objective of this numerical investigation is to analyze the influence of location, width and slope of the slots and therefore identify the optimal configuration. The approach is based on two dimensional cascade geometry, low speed regime, steady state and turbulent RANS model. The results show the efficiency of this passive technique to delay separation and enhance aerodynamic performances of the compressor cascade. A maximum of 28.3% reduction in loss coefficient have been reached, the flow turning is increased with approximately $5^0$ and high loading over a wide range of angle of attack have been obtained for the optimized control parameter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.126-133
• /
• 2016

This paper proposes a new PWM method to reduce the common mode voltage change in three-level Vienna rectifier. This new proposed PWM method uses medium voltage vector for the three-level Vienna rectifier to determine the sum of three-phase voltage zero, and the common mode voltage variation is decreased. Using the carrier comparison method, the switching function generator for three-level Vienna rectifier has been proposed. The effects of the proposed PWM method have been verified through simulation using the PSIM.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.226-228
• /
• 1999

This paper presents an efficient analysis method using time-stepping finite element method for electric machines driven by pulse width modulation (PWM) inverter. In the method, the value of time-step is changed according to the PWM logic of inverter, and the calculation time can be reduced while maintaining analysis accuracy. Using the method, the dynamic characteristics of a permanent magnet linear synchronous motor (PMLSM) driven by PWM inverter are analyzed.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.757-759
• /
• 2000

The problem in improving the positioning precision of a permanent magnet linear synchronous motor(PMLSM) is the large detent force caused by the permanent magnet. The detent force is thought to arise from the difference of the position of a permanent magnet end and a tooth position. In this paper, Three methods of reducing detent force is presented The first method is adjusting the width of permanent magnet. The second method is varying the shape of armature teeth. The third method is the arrangement of the permanent magnet end. This paper compares with the ratio of reducing the detent force according to the three methods.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.2
• /
• pp.153-158
• /
• 1992

We propose, in this paper, a new thinning algorithm and demonstrate Its effectiveness with some concrete experimental results. This new thinning process can solve the problems of disconnectivity and end point reduction explored in one-Pass algorithm Furthermore, this algorithm is proven effective particularly In high speed operation. A processor for this algorithm that is capable of hand-ling Input Image width(between 25 and 4t) bits ) and also operates on pipelining, is implemented and tested. Flexibility and high speed operation of this thinning processor should find excellent applicability in various areas.