• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.5
• /
• pp.31-46
• /
• 1999

A drying paper strives to shrink due to the shrinkage of the individual paper fibres. Laboratory results show that a reduction of the shrinkage or an imposed stretch leads to a large increase in tensile stiffness and a large decrease in strain at break. In c cylinder drying section the water in the web is repeatedly heated on the drying cylinder and evaporated in the free draw. To evaluate the drying process regarding influence on paper properties these sub-processes, or drying phases, have to be studied separately. The effect of the conditions on the drying cylinder and on the VacRoll is investigated in pilot trails. Both the fabric tension on the drying cylinder and on the VacRoll reduces the shrinkage of the paper. The laboratory results are used as input to a numerical simulation of the conditions in the free draw. If the web width is increased or the length of the free draw is reduced the mean shrinkage of the paper web is reduced . However, the difference in shrinkage between the middle and the edge of the web is increased.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.139-142
• /
• 2006

This paper describes a new method using random modulated strategies for switched reluctance machines. The proposed method is combined random turn-on, turn-off angle technique and random pulse width modulation technique. The purpose of this proposed method is to decrease harmonic spectrum, and thus reduce the emitted acoustical noise. A random generator is generated by linear congruential generator (LCG) using random pulse position (RPP) scheme. Simulation results show that the harmonic intensity of proposed method is better than that of conventional method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.293-298
• /
• 1995

The strength of shear connectors embedded in lightweight concrete slab with deck plate is influenced by various factors of deck plate, shear conncetor and concrete. Generally, it is reported that the strength of shear connector in lightweight concrete decreases in comparison with that in normal concrete. So this paper is to use compressive strength of lilghtweight concrete, width-height ratio of deck plate, and cross sectional area of shear conncetor as variables, to evaluate the strength of shear conncetors in composite beam of steel and lilghtweight concrete slabs with deck plate, and then to suggest the reasonable strength equation by comparing the push-out test results with establixhed strength formula. As the result of 24 specimens test, in case of lightweight concrete slab with deck plate, it has showed that in the same strength, the strength of shear connector decreased about 10~20% in comparison with that in normal concrete. In spite of lightweight concrete, the test results were closely approached the established strength formula of shear connector using Fisher's reduction coefficient.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.379-381
• /
• 1994

This paper is concerned with a zero-voltage soft-switching PWM DC-DC high-pelter converter using IGBTs, which Bakes the most of the parastic LC parameters of high-voltage transformer link, for diagnostic X-Ray power generator. The converter circuit basically utilizes phase-shift pulse width modulated series resonant full-bridge PWM DC-DC high-Power converter operating at a constant frequency:20kHz. This technique brings about dramatic decreases in the switching losses of power devices and their electrical stresses as compared with the commonly-used hard-switching PWM DC-DC power converter. The high-frequency switching operation of the converters has some effective advantages, which consist in the physical reduction in size and weight and lowered acoustic noise.

• Journal of the Korean Society of Safety
• /
• v.30 no.2
• /
• pp.70-76
• /
• 2015

This study deals with the traffic accident of circular intersections. The purpose of the study is to develop the accident models by traffic violation type. In pursuing the above, this study gives particular attention to analyzing various factors that influence traffic accident and developing such the optimal models as Poisson and Negative binomial regression models. The main results are the followings. First, 4 negative binomial models which were statistically significant were developed. This was because the over-dispersion coefficients had a value greater than 1.96. Second, the common variables in these models were not adopted. The specific variables by model were analyzed to be traffic volume, conflicting ratio, number of circulatory lane, width of circulatory lane, number of traffic island by access road, number of reduction facility, feature of central island and crosswalk.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.2
• /
• pp.113-119
• /
• 2006

This paper studies the torque characteristics of CDTP controlled BLDCM with various back-EMF waveforms. We propose a CDTP method to suppress torque pulsation due to commutation time and point. It is adopted to control the BLDCM with real back-EMF waveforms through the Hague's method for minimizing torque ripple. Real back-EMF waveforms are produced with a magnetic fringing factor and crest width of back-EMF. The performance and characteristics of the proposed control method are analyzed by simulation and verified through experimental results.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.67-69
• /
• 2004

This paper describes an approach to design a interior permanent magnet motor(IPM motor) for the reduction of cogging torque. The magnitude of the torque ripple and cogging torque in a interior permanent magnet motor(IPM motor) are generally dependent on several major factors: the shape of stator tooth tip, slot opening width, air gap length, the shape of barrier preventing flux leakage of magnets, magnet configuration and magnetization distribution or magnet poles. In this paper, the IPM BLDC motor is designed considering a saturated leakag flux between the barriers on the rotor for increasing the efficiency and decreasing the magnitude of the cogging torque. Analytical model is developed for the IPM BLDC motor with a concentrated winding stator. The results verifies that the proposed design approach is very efficient and effective in reducing the cogging torque and the torque ripple of the IPM BLDC motor to be used in an electric vehicle.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.887_888
• /
• 2009

In this paper, an advanced torque control scheme of Switched Reluctance Motor (SRM) using modified non-linear logical TSF (Torque Sharing Function) based on the DITC (direct instantaneous torque control) with PWM(Pulse Width Modulation). In the proposed control scheme, a simple calculation of PWM duty ratio, switching rules from DITC and non-linear torque sharing function can reduce the torque ripple with fixed switching frequency. The proposed control scheme is verified by the computer simulations and experimental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.6
• /
• pp.1105-1109
• /
• 2009

This paper deals with a polynomial thrust equation of a permanent magnet linear synchronous motor that is considered by a skew and overhang effects of permanent magnet. The skew length, the overhang length, the width and height of permanent magnet, the teeth length and air-gap length which effect to the flux density of air-gap are selected as variables of the polynomial thrust equation. Polynomial thrust equation is elicited by the 6 parameters. The results are satisfied that the values by polynomial thrust equation are compared ones by using 3-dimensional finite element analysis and experiment.