• Journal of Auto-vehicle Safety Association
• /
• v.13 no.1
• /
• pp.6-13
• /
• 2021

This paper presents yaw moment control for modification of steering characteristic in rear-driven vehicle with front in-wheel motors (IWMs). The proposed control algorithm is designed to modify yaw rate response of the test vehicle. General approach for modification of steering characteristic is to define the desired yaw rate and track the yaw rate. This yaw rate tracking method can cause the chattering problem because of the IWM actuator response. Large overshoot and settling time in IWM torque response can amplify the oscillation in control input and yaw rate. To resolve these problems, open-loop IWM controller for cornering agility was designed to modify the understeer gradient of the vehicle. The proposed algorithm has been investigated via the computer simulations and the vehicle tests. The performance evaluation has been conducted on dry asphalt using E-segment test vehicle. The performance of the proposed algorithm has been compared to general yaw rate tracking algorithm in the vehicle tests. It has been shown that the proposed control law improved the cornering agility without chattering problem.

• International Journal of Automotive Technology
• /
• v.7 no.7
• /
• pp.803-812
• /
• 2006

In order to reduce the negative effects of dynamic coupling among vehicle subsystems and improve the handling performance of vehicle under severe driving conditions, a vehicle chassis control integration approach based on a main-loop and servo-loop structure is proposed. In the main-loop, in order to achieve satisfactory longitudinal, lateral and yaw response, a sliding mode controller is used to calculate the desired longitudinal, lateral forces and yaw moment of the vehicle; and in the servo-loop, a nonlinear optimizing method is adopted to compute the optimal control inputs, i.e. wheel control torques and active steering angles, and thus distributes the forces and moment to four tire/road contact patches. Simulation results indicate that significant improvement in vehicle handling and stability can be expected from the proposed chassis control integration.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.1
• /
• pp.73-78
• /
• 2013

In this paper, configuration control for the Horizontal Maintenance of the 2 wheel robot has been studied using ARS(Attitude Refrence System). The 2 wheel robot technique is getting attention and there have been many researches on the seg-way since the US. Using its 2 freedom, a 2 wheel robot can move in various modes and Our robot performs goal reaching ARS.2 wheel robot fall down to the forward or reverse direction to converge to the stable point. Kalman Filter is normally used for the algorithm and numerous research is progressing at the moment. To calculate the attitude in ARS using 2 axis gyro(roll, pitch) and 3 axis accelerometers (x, y, z). In this paper we present a two wheel robot system for an autonomous mobile robot. This paper realized the robot control method which is much simpler but able to get desired performance by using the ARS control.

• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.57-63
• /
• 2004

Conventionally, 2WS is used for vehicle steering, which can only steering front wheel. In case of trying to high speed lane change or cornering through this kind of vehicle equipped 2WS, it may occur much of Yaw moment. On the other hand, 4WS makes decreasing of Yawing Moment, outstandingly, so it is possible to support vehicle movement stable. And conventional ABS and TCS can only possible to control the longitudinal movement of braking equipment and drive which can only available to control of longitudinal direction. There after new braking system ESP was developed, which controls both of longitudinal and lateral, with adding of the function of controlling Active Yaw Moment. On this paper, we show about not only designing of improved braking and steering system through establishing of the integrated control system design of 4WS and ESP but also designing of the system contribute to precautious for advanced vehicle stability problem.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.33-38
• /
• 2016

The turbocharger is an essential component to realize the engine down-sizing. The moment of inertia of turbocharger rotor is an important parameter with respect to acceleration performance of the vehicle. It can be calculated from the CAD software based the geometry data and the material properties. But the accurate value of the inertia of turbocharger rotor must be measured through the experimental method. In this study, the measurement of moment of inertia of turbocharger rotor for 2.0 L spark-ignition engine was carried out. First, an experimental equipment using a trifilar method was designed and fabricated. Some optical devices, that is, photo sensor, counter, convex lens, etc, were used to increase the accuracy of the measurement. Second, error sensitivity for the equipment was analyzed. The error of period time and the radius can give big affects to the accuracy of the moment of inertia. When the amount of error of these two were each 1.0 %, maximum error of the moment of inertia was under 3.0 %. Third, the calibration for the equipment was performed using a calibration rotor which has similar shape to turbine rotor but simple. Calculated value from CAD software and measured one for the calibration rotor were compared. The total error of the equipment and the measurement is about 1.3 %. This result shows that the equipment can give the good result with resonable accuracy. Finally the moment of inertia of the turbine rotor and compressor wheel were measured. The coefficient of variations, the ratio of standard deviation to mean value, were reasonably small at 0.57 % and 0.73 % respectively. Therefore this equipment is suitable for the measurement of the moment of inertia of the turbine rotor and compressor wheel.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.36.3-36.3
• /
• 2008

KARI (Korea Aerospace Research Institute) is going to launch a Communication, Ocean and Meteorological Satellite (COMS) at summer of 2009. It will be first thing to be developed for a geostationary satellite through domestic technology. Of course, KARI has performed this development program with EADS Astrium in France since 2005. COMS has the non-symmetric configuration that the solar array is only attached on the south panel. Due to the configuration, momentum of satellite will be rapidly accumulated induced by solar pressure and then 3 wheels of large momentum are located on roll-yaw plane for attitude control. Therefore, to prevent the saturation of wheel momentum, wheel off-loading will be performed two times per day during 10 minutes for each one. At the moment, translation movement on 3-axes direction appears because of using thrusters. In this paper, strategy of the wheel off-loading and triaxiality which is the translation effect on 3-axes are introduced. Consequently, the result of optimized triaxiality considering the wheel off-loading strategy is summarized.

• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.92-99
• /
• 2015

The diameter of a new wheel in EMUs is 860mm and it can be used up to 773mm. To obtain an predefined acceleration despite wheel diameter changes, the tractive efforts of the vehicles must be properly controlled. In the commencement of this study, acceleration tests were performed for empty EMUs when the wheel diameter was changed to 860mm, 820mm and 780mm, respectively. In order to deal with more complicated running conditions, we developed dynamic simulation models of the EMUs using VI-Rail, and simulated the models in empty and full passenger loads, respectively. Using the simulation results, we analyzed the gradient of time-velocity graphs by considering the changes of the total weight vehicles and moment of inertia of the wheelsets as well as tractive effort according to the wheel diameter changes. As the results, it was found that there are significant differences in acceleration performances according to the wheel diameters and the payloads of EMUs. In case of 860mm which is the maximum wheel diameter, the test & simulation results show that the vehicle couldn't reach the predefined acceleration, 3.0km/h/s, due to lack of tractive effort.

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.836-844
• /
• 2000

In this research any abnormal motion of a vehicle is detected by utilizing the difference between the reference and actual yaw velocities as sell as the information on vehicle slip angle and slip angular velocity. This information is then used as a criterion for execution of the yaw moment control. A yaw moment control algorithm based on the brake control is proposed for improving the directional stability of the vehicle. The controller executes brake controls to provide each wheel with adequate brake pressures, which generate the needed yaw moment. It is shown that the proposed yaw moment control logic can provide excellent cornering capabilities even on low friction roads. This active control scheme can prevent a vehicle from behaving abnormally, and can assist normal drivers in coping with dangerous situations as well as experienced drivers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.39-51
• /
• 1996

In the turning maneuver of the vehicle, its motion is mainly dependent on the genuine steering characteristics in view of the directional stability for stable turning ability. The under steer vehicle has an ability to maintain its own directonal performance for unknown external disturbances to some extent. From a few years ago, in order to acquire the more enhanced handling performance, some types of four wheel steering vehicle were considered and constructed. And, various rear wheel control logics for external disturbances has not been suggested. For this reason, in this posed rear wheel control logic is based on the yaw rate feed back type and is slightly modified by an yaw rate tuning factor for more stable turning performance. And an external disturbance is defined as a motivation of the additional yaw rate in the center of gravity by an uncertain input. In this study, an external disturbance is applied to the vehicle as a form of the additional yawing moment. Finally, the proposed rear wheel control logic is tested on the multi-body analysis software(ADAMS). J-turn and double lane change test are performed for the validation of the control logic.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1326-1330
• /
• 2008

The failure mode of steel road wheels in a vehicle is cracks from ventilation hole through to contact plane on steel wheel's disc plate. But a number of cracks of Cornering Fatigue Limit Test is on contact plane near to wheel nut mounting area, even though it's satisfied with specified cycles. So this paper searches out causes to improve durability and reliability of C.F.T by uni-axial bending moment test. The verified cause is a "fretting" on contact area of steel wheel. In result, this paper suggests a solution to prevent a fretting by inserting a damping shim, 0.7mm between steel wheel contact areas. Therefore this paper makes it possible to move crack position of C.F.T in steel wheel from contact plane to vehicle's failure mode.