• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.59-67
• /
• 2014

A numerical model and a controller of Active Front wheel Steer (AFS) system are designed in this study. The AFS model consists of four sub models, and the AFS controller uses sliding mode control and PID control methods. To test this model and controller an Integrated Dynamics Control with Steering (IDCS) system is also designed. The IDCS system integrates an AFS system and an ARS (Active Rear wheel Steering) system. The AFS controller and IDCS controller are compared under several driving and road conditions. An 8 degree of freedom vehicle model is also employed to test the controllers. The results show that the model of AFS system shows good kinematic steering assistance function. Steering ratio varies depends on vehicle velocity between 12 and 24. Kinematic stabilization function also shows good performance because yaw rate of AFS vehicle tracks the reference yaw rate. IDCS shows improved responses compared to AFS because body side slip angle is also reduced. This result also proves that AFS system shows satisfactory result when it is integrated with another chassis system. On a split-m road, two controllers forced the vehicle to proceed straight ahead.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.813-818
• /
• 2005

In this paper, a re-adhesion control scheme is proposed for 1C2M propulsion system of TTX. The possibility of slip between wheel and rail in railway system is increasing because of the tendency of high speed and a climatic change. This slip results in the decrease of adhesive effort between this wheel and rail, so the control strategy of traction effort which can reduce the speed promptly and make most use of the maximum adhesive force is absolutely necessary. This paper describes the modeling of the TTX system, and this system is verified by the simulation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.41-50
• /
• 1998

In this study, to investigate a characteristics of slip ratio control of H.C.U for ABS, half car model tester were developed and a new H.C.U. was compactly designed comparing to the commercical H.C.U. for ABS. In half car model tester, variable inertia wheel has been used to load the car weights and braking forces according to the road surface conditions which were realized by pneumatic cylinder. And solenoid valves using P.W.M. (Pulse Width Modulation) method were installed in the new H.C.U The slip ratio characteristics of tire had been measured using half car model tester and the results were used in the control simulation for a new H.C.U.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.56-61
• /
• 2007

In the braking of railway rolling stock, the slip that is the relative velocity between train body and its wheel affects the adhesive force which is connected to the braking force. The coefficient of the adhesive force changes in accordance with the slip and the condition of a rail road. Namely, its value increases upon the maximum on a rail condition, and there it declines conversely while the magnitude of slip keeps rising on. First, this paper introduced a reference slip generator so that can utilize maximum adhesive forces with a disturbance observer for estimating unmeasurable current adhesive forces which is as an input of the generator. And, an adaptive sliding-mode control system has been synthesized for minimizing the error between reference and current slip. Finally the effectiveness of the proposed control system is evaluated by computer simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.783-786
• /
• 1991

Generally, The position of mobile robot moving on the plane is measured by the method of dead reckoning, using the encoder system coupled on a wheel axis. But it is noted that the encoder system cannot check the slip of a wheel, often occurring in tracking of the mobile robot. In this study, using velocity angular velocity sensor with a tuning fork vibration system, the system is developed which can measure the directional angle of positional variables on the mobile robot. By measuring the variations of tracking direction mobile robot equipped with this system, following result is found; In spite of the slip at a wheel when measuring the tracking directional angle, the error occurs in the range of .+-. 1 (degree).

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.836-844
• /
• 2000

In this research any abnormal motion of a vehicle is detected by utilizing the difference between the reference and actual yaw velocities as sell as the information on vehicle slip angle and slip angular velocity. This information is then used as a criterion for execution of the yaw moment control. A yaw moment control algorithm based on the brake control is proposed for improving the directional stability of the vehicle. The controller executes brake controls to provide each wheel with adequate brake pressures, which generate the needed yaw moment. It is shown that the proposed yaw moment control logic can provide excellent cornering capabilities even on low friction roads. This active control scheme can prevent a vehicle from behaving abnormally, and can assist normal drivers in coping with dangerous situations as well as experienced drivers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.428-436
• /
• 1998

A TCS slip control system improves acceleration capability and steerability on slippery roads through engine torgue and/or brake torque control. This research mainly deals with the engine control algorithm via the adjustment of the engine throttle angle. The following new control strategy is proposed and investigated ; the TCS slip controller whose input is the difference between the desired driving wheel speed corresponding to the optimum slip ratio and the actual speed yields the target engine torque and then estimates the throttle angle based on the engine performance curve. Various simulation and hardware-in-the-loop simulation have been carried out. The results show the proposed strategy may compensate for the inherent nonlinearity between variation of the throttle angle and variation of the engine torque and produce better performance than the previous strategies without the engine map, especially in the high speed region.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.133-138
• /
• 1993

This paper presents neural network based position estimation method in slippery environment as an approach to solve one of problems which are engaged in dead reckoning method. Position estimator is composed of slip detector and linear velocity estimator. Both of them are based on the fact that dynamic characteristic of mobile robot in slippery environment is different from the case without slip. To find out the dynamic relation among driving torque, angular acceleration of driving wheel and linear acceleration of mobile robot, accelerometer is used for measuring acceleration of mobile robot and neural network is used for dynamic system identifier in slippery environment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.248-251
• /
• 2004

Stability of truck and trailer are the most significance in Thai automotive industry. This paper presents the mathematical model of a six-degree-of-freedom semi-trailer vehicle. Search method was implemented to obtain the optimum design variables of the trailer which are the distance from the fifth wheel to the centroid of the trailer and the distance from the centroid of the trailer to the trailer axel. The objective function is to minimize the steady side slip velocity, steady-state yawing velocity and steady-state angle between the tractor and the trailer. From the calculation , the optimum distance from the fifth wheel to the centroid of the trailer and the optimum distance from the centroid of the trailer to the trailer axle are 5.50 and 3.25 meters respectively. The stability of the optimal semi-trailer vehicle was also examined in steady state. The steady side slip velocity, yawing velocity and the angle between tractor and trailer are also obtained using linearization technique under unit step disturbance of the tractor front wheel steering angle.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.15-21
• /
• 2010

A differential case equipped with LSD(limited slip differential) has several advantages over a normal type for rear wheel drive vehicles. Specially, the torque distribution can be done between left and right drive wheel in the state of limited slip differential. Also although LSD types are very various according to operating type, medium and torque distribution, a multi-clutch type is generally applied to rear wheel drive vehicles. So, this study presents the analysis of design parameters for development of a friction plate for multi-clutch type LSD using vehicle road test, the simulation of analytical model and the development of vehicle dynamics model by a benchmark product. According to this investigation, the design parameters which are pre-load of coil spring, friction plate and contact area quantity, friction coefficient and TBR(torque bias ratio) for a friction plate are derived from experiment and simulation and consequently, vehicle dynamics model has been constructed for the development of friction plate for multi-clutch type LSD.