• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.832-842
• /
• 1996

TAME synthesis was studied in a fixed bed reactor with 3 different types of exchanged resins i.e, Amberlyst-15, Amberlyst-15(wet) and Amberlyst XN-1010. Amberlyst-15 has highest activity, presumably due to the higher reaction participation of the inner active sites of gel shape microparticular resin structure. The optimum reaction conditions for TAME synthesis were found as follows ; reaction temperature of $135^{\circ}C$, molar ratio(MeOH/I.A.A) of 1.0~4.0 and W/F of 2.0~4.0 gr.-cat. hr/gr.-mole. The cross-linking bond of styrene divinyl benzene was observed at $2{\theta}=20$ in XRD pattern. The DSC analysis showed that the thermal stability was in order of Amberlyst-15>Amberlyst-15(wet)>Amberlyst XN-1010. The apparent activation energies of TAME synthesis reaction with Amberlyst-15, Amberlyst-15(wet) and Amberlyst XN-1010 were 12.36, 12.46 and 14.72 kcal/mole, respectively.

• Journal of the Korean Ceramic Society
• /
• v.30 no.3
• /
• pp.215-221
• /
• 1993

The Hydroxyapatite powders were prepared by Wet-direct and Hydrothermal synthesis using Ca(NO3)2.4H2O and (NH4)2.HPO4.Stoichiometric and good cristalline HAp powders were obtained 9$0^{\circ}C$ by wet-direct process. The aspect ratio of HAp powders prepared by hydrothermal synthesis was increased with increasing synthetic temperature. The HAp particles obtained at 20$0^{\circ}C$ for 10hr were needle shaped ultra fine crystals, about 100nm in size. Small amount of TCP was obtained above 80$0^{\circ}C$ after heat-treatment of hydrothermally synthesized HAp but good crystalline HAp phase was maintained up to 120$0^{\circ}C$ as the primary phase.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.11-18
• /
• 2013

Interest in copper nanoparticles has increased as an alternative for substituting silver nanoparticles because of its lower cost and less electromigration effect than silver. In this paper, the recent research trends and main results in wet-chemical synthesis of sub-100 nm Cu nanoparticles were summarized. The characteristics of synthesis were discussed with a classification such as modified polyol synthesis, modified hydrothermal synthesis, solvothermal synthesis, and the others, focussing on effects of capping agents, reductants, and pH. Information on the oxidation of synthesized copper nanoparticles were additionally commented.

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.43-46
• /
• 2012

A fluidized bed drying approach was utilized to the synthesis of water glass based silica aerogel powders. The effects of the fluidized bed drying conditions such as the superficial velocity and temperature of hot air and bead size as well as bead/wet-gel ratio, on the physical properties such as tapping density and productivity of the aerogel powders were systematically investigated. The experimental results showed that the amount of beads mixed with wet-gels in the fluidized bed column has the most profound impact on the fluidization efficiency, greatly enhancing the yield of the aerogel powders up to 98% with a proper bead/wet-gel weight ratio as compared to 72% without using beads. No significant change was observed in the tapping density over a wide range of the fluidized drying condition. Consequently the fluidized bed drying approach shows a good promise as an alternative route for the large-scale production of the aerogel powders.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.698-704
• /
• 1999

Li rich Li1+xMn2-xO4(x=0.07) spinel powders were prepared by an oxalate precipitation of wet chemical methods at temperature lower than $600^{\circ}C$. The FTIR results showed that the powders prepared at $600^{\circ}C$ had high degree of crystal quality comparing with the spinel powders prepared by solid state reaction at 75$0^{\circ}C$ which was the lowest synthesis temperature of the solid state reaction method. The particle size of powders prepared by the oxalate precipitation at $600^{\circ}C$ was smaller than 0.2${\mu}{\textrm}{m}$ and the specific surface area was 11.01 m2/g A heat treatment over 90$0^{\circ}C$ formed second phase in the precipitates. It was shown that there were phase transitions at temperatures. T1,T2 and T2. The transitions involved weight loss and gain during heating and cooling. The low temperature synthesis below $600^{\circ}C$ avoided the second phase formation and the prepared powders showed improved compositional and physical properties for secondary lithium battery applications.

• Journal of the Korean Ceramic Society
• /
• v.21 no.2
• /
• pp.165-173
• /
• 1984

It is desirable to establish reliable synthetic methods for electro-ceramic materials. To synthesize $SrTiO_3$ in this study direct solid state reactions and wet chemical processes were used. Previous study of $SrTiO_3$ synthesis included oxalated-method($SrTiO(C_2O_4)_2$.$4H_2O$) co-precipitation$(SrCO_3+TiO(OH)_2)$ and direct solid state reaction$(SrCO_3+TiO(OH)_2)$ The methods in question lead to intermediate inclusion during the reactions and less controllable in particle sizes of $SrTiO_3$. To obtain highly pure $SrTiO_3$ so-called "direct wet process method" was added in this investigation. In the study the "direct wet process" was for the first time applied to synthesize chemically pure and fine particle $SrTiO_3$. $SrCl_2$ and $TiCl_4$<\ulcornerTEX> at KOH solution at room temperature to 10$0^{\circ}C$ precipitated $SrTiO_3$ The particle size increased as temperature increased.mperature increased.

• Applied Science and Convergence Technology
• /
• v.26 no.6
• /
• pp.164-173
• /
• 2017

Across the most industry, the demand for nanoparticles is increasing. Therefore, many studies have been carried out to synthesize nanoparticles using various methods. The aim of this paper is to introduce an industry-applicable as well as financially and environmentally effective solution plasma process. The solution plasma process involves fewer chemicals than the traditional kit, and can be used to replace many of the chemical agents employed in previous synthesis of nanoparticles into plasma. In this study, this process is compared to the wet-reaction process that has thus far been widely used in the most industry. Furthermore, the solution plasma process has been classified into four different types (in-solution, out of solution, direct type, and remote type), according to its plasma occurrence position and plasma types. Thus, the source of radicals, nanoparticle synthesis, and modification methods are explained for each design. Lastly, unlike nanoparticles with hydrophilic functional groups that are made inside the solution, a nanoparticle synthesis and modification method to create a hydrophobic functional group is also proposed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.278-283
• /
• 1995

The potassium titanate fibres were synthesized with wet process by the addition of KOH solution to the TiOz gel produced by the reaction between element titanium particles and $H_2O_2$ solution at $50^{\circ}C$. And then they were characterized by XRD, SEM and FT - IR. It was found that potassium titanate fibres were mainly affected by KOH/TiOz mole ratio, synthesis time and aging time in this wet process employed. For $KOH/TiO_2 = 1/1$, synthesizing time 24 hrs, aging time 24 hrs and calcination temperature of TEX>$900^{\circ}C$ for 1 hr, their products were mainly found to be potassium tetratitanate which had thin and long fibres in the range of 10 ~ 20 mm. As the synthesizing time increased and the amount of KOH decreased, potassium tetratitanate was converted into potassium hexatitanate. Also, the length of their fibres became short.

• Journal of Ceramic Processing Research
• /
• v.20 no.6
• /
• pp.655-659
• /
• 2019

Calcium phosphates such as HA (hydroxyapatite), β-TCP (tricalcium phosphate) and biphasic HA/β-TCP, were synthesized by wet chemical precipitation in aqueous solution combined with ball milling process. Nanosize powders of the calcium phosphates were synthesized using Ca(OH)2 and H3PO4. The effects of initial precursor Ca/P ratio (1.30, 1.50 and 1.67), ball milling process and post heat-treatment on the phase evolution behavior of the powders were investigated. The phase of resulting powder was controllable by adjusting the initial Ca/P ratio. HA was the only phase for as-prepared powders in both cases of Ca/P ratios of 1.50 and 1.67. The single HA phase without any noticeable second phase was obtained for the initial Ca/P ratio of 1.67 in the overall heat-treatment range. Pure β-TCP and biphasic calcium phosphate (HA/β-TCP) were synthesized from precursor solutions having Ca/P molar ratios of 1.30 and 1.50, respectively, after having been heat-treated above 700 ℃. The β-TCP phase has appeared on the pre-existing DCPD (dicalcium phosphate dihydrate) and/or HA phase. Dense ceramics having translucency were obtained at a considerably lower sintering temperature. The modified process offered a fast, convenient and economical route for the synthesis of calcium phosphates.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.843-850
• /
• 1991

There is a growing demend for absorptive electromagentic shielding materials for wide band frequency application. In this study, the absorber which consists of a rubber plus Ni-Zn ferrite which have been prepared by direct-wet method. A rubber ferrite composite for electromagnetic shielding, it is most importan facter the homogeneous ultra fine size and high dispersitive ferrite powder. Direct-wet method and solid-solid reaction method for preparing of ultra fine ferrite powder was used. It has been experimentally verified that the powder which prepared by direct-wet method was very fine and almost same size spherical powder, the composite ferrite have excellent electromagnetic wave absorption in X-band.