• Membrane Journal
• /
• v.15 no.2
• /
• pp.147-156
• /
• 2005

It is well-known that polyethersulfone (PES) has high $CO_2$ selectivity over $N_2\;(or\;CH_4)$ and excellent pressure resistance of $CO_2$ plasticization among muy commercialized engineering plastics[1-4]. Asymmetric PES hollow fiber membranes for flue gas separation were developed by dry-wet spinning technique. The dope solution consists of PES, NMP and acetone. Water and water/NMP mixtures are used in outer and inner coagulants, respectively. Gas permeation rate (i.e., permeance) and $CO_2/N_2$ selectivity were measured with pure gas, respectively and the micro-structure of hollow fiber membranes was characterized by scanning electron microscopy. The effects of polymer concentration, ratio of NMP to acetone, length of air gap, evaporation condition and silicone coating were investigated on the $CO_2/N_2$ separation properties of the hollow fibers. Optimized PES hollow fiber membranes exhibited high permeance of $25\~50$ GPU and $CO_2/N_2$ selectivity of $30\~40$ at room temperature and have the apparent skin layer thickness of about $0.1\;{\mu}m$. The developed PES hollow fiber membranes, would be a good candidate suitable for the flue gas separation process.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.E
• /
• pp.9-17
• /
• 1998

Oxides of nitrogen play important roles in atmospheric chemistry. Soil has been recognized as a major natural source of NO, and its emission depends on soil parameters such as soil nitrogen availability, soil moisture and temperature. It is necessary to understand effects of these controlling parameters on soil NO emission. In order to understand soil moisture effects on NO emission, variations of NO concentration and existence of its equilibrium concentration were observed from ammonium fertilized Japanese upland soil prepared for different soil moisture conditions. The closed chamber technique was employed for this study. The significant increases in NO with soil moisture were found. Maximum was occurred at sample ID4 (55% of water-filled pore space (WFPS)), but it decreased as soil moisture increased. No significant NO concentration was emitted from soil sample without fertilizer, but there was significant NO in fertilized soil samples. The magnitudes of NO from soil increased with time and reached at steady state within ten minutes approximately. These results suggest that nitrogen input from fertilizer takes charge in the first step of sharp increase in NO emission, and then soil moisture becomes important factor to control NO emission from the soils. NO concentrations from soil were compared to those one-day after the experiment. Results from the comparison analysis suggest that the soil NO flux might have been stimulated by soil disturbances like mixing, and this is much more effective in dry soils rather than in wet soils. It was found that much less NO came out from soils after a day; suggesting that most of NO was released from the soils within a day after fertilizer application during our experiment. The length of NO releasing time span may depend on the amounts of fertilizer applied, soil moisture condition, and other soil physical parameters.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.2
• /
• pp.77-90
• /
• 2015

The fission track registration techniques for accurate determinations of uranium in solid- and liquid-state geological materials were recommended and their applicability were examined. The determination of uranium can be achieved by optical counting of neutron-induced fission tracks of $^{235}U$ registered on solid-state track detectors under high magnification. In a dry registration method using powdered pellets of rocks (e.g., granite and coal) showing good uranium-affinity, it was not easy to decide an overall mean concentration over the total sample owing to track-clusters caused by frequent presence of uranium-bearing minerals. Separate scanning for homogeneous and track-clustered parts may be an alternative choice. Assuring the homogeneity over the whole sample, high reproducibilities were confirmed both from duplicate detections using mica and Lexan polycarbonate detectors and from multiple measurements at different thermal neutron fluences. The wet registration method using sealed quartz tubes is recommended to overcome the common heterogeneity in uranium concentrations of $10^1ppm$ and more. Adopting the wet registration, the uranium homogeneity was recovered below the $10^0ppm$ level and the lower detection limit was proved to reach without difficulty the $10^2ppb$ (i.e. $ng\;g^{-1}$) level.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.167-176
• /
• 2021

When producing recycled asphalt mix, it is important that the old binder of reclaimed asphalt pavement(RAP) should be well melted during blending in the mixer. The recycled asphalt mix is produced by instant mixing(IM) of all materials(RAP, virgin asphalt and new aggregates) all together in the mixer. However, in the same recycled mix, the binder around RAP aggregate was found to show higher oxidation level than the binder coated around the virgin aggregate because the old binder of RAP was not rejuvenated properly while instant mixing. The partially-rejuvenated RAP binder is assumed to be a high stiffness point in IM recycled mix. In this study, the stage mixing(SM) method was introduced; blending RAP and virgin asphalt for the first stage, and then mixing all together with hot new aggregates for the second stage. To compare the effect of the two mixing methods on moisture resistance of recycled mixes, a statistical t-test was performed between SM and IM using indirect tensile strength(ITS) and tensile strength ratio(TSR). Three conditioning methods were used; a 16-h freezing and then 24-h submerging, 48-h submerging, and 72-h submerging in 60℃ water. It was found that the TSR(=ITS_wet/ITS_dry) values of the mixes prepared by SM was clearly higher than the IM mixes, and coefficients of variation of SM mixes were lower than the IM mixes. It was also observed that the ITS_WET of SM was significantly different from the IM at α=0.05 level by statistical t-test. The ITS_WET of SM mix was reduced less than the IM mix in severer conditioned mixes. Therefore, it was concluded that the stage mixing method was an important blending technique for producing better-quality of recycled asphalt mixes, which would show higher moisture resistance than the recycled mixes produced by conventional instant mixing.

• Advances in nano research
• /
• v.5 no.3
• /
• pp.193-201
• /
• 2017

ZnO, ZnO: Cu, Ga, and ZnO: Cu, Ga, Ag thin films were obtained by oxidization of ZnS and ZnS: Cu, Ga films deposited onto glass substrates by electron-beam evaporation from ZnS and ZnS: Cu, Ga targets and from ZnS: Cu, Ga film additionally doped with Ag by the closed space sublimation technique at atmospheric pressure. The film thickness was about $1{\mu}m$. The oxidation was carried out at $600-650^{\circ}C$ in air or in an atmosphere containing water vapor. Structural characteristics were investigated by X-ray diffraction (XRD) and atomic force microscopy (AFM). Photoluminescence (PL) spectra of the films were measured at 30-300 K using the excitation wavelengths of 337, 405 and 457.9 nm. As-deposited ZnS and ZnS: Cu, Ga films had cubic structure. The oxidation of the doped films in air or in water vapors led to complete ZnO phase transition. XRD and AFM studies showed that the grain sizes of oxidized films at wet annealing were larger than of the films after dry annealing. As-deposited doped and undoped ZnS thin films did not emit PL. Shape and intensity of the PL emission depended on doping and oxidation conditions. Emission intensity of the films annealed in water vapors was higher than of the films annealed in the air. PL of ZnO: Cu, Ga films excited by 337 nm wavelength exhibits UV (380 nm) and green emission (500 nm). PL spectra at 300 and 30 K excited by 457.9 and 405 nm wavelengths consisted of two bands - the green band at 500 nm and the red band at 650 nm. Location and intensities ratio depended on the preparation conditions.

• Asian-Australasian Journal of Animal Sciences
• /
• v.8 no.3
• /
• pp.267-273
• /
• 1995

The differences in rumen particle pool size, passage rate and rumen degradability in sheep receiving three varieties of orchardgrass hay harvested at pre-heading (H1), early-bloom (H2) and late-bloom (H3) were investigated using four ruminal-cannulated wethers (68 kg) fed 1,300 g of the hay once a day. Representative samples of whole rumen contents were collected at different times after feeding and the quantities of rumen particle pools [large particle pool (LPP), retained on a $1,180{\mu}m$ sieve; small particle pool (SPP), retained on a 47 but passed a $1,180{\mu}m$ sieve; and soluble fraction (SOL), passed a $47{\mu}m$ sieve (SOL)] were determined by a wet-sieving technique. The fullowing results were obtained: 1) The dry weight of whole rumen contents were significantly lower (p < 0.05) for HI than for H2 or H3. The reduction rate of whole rumen contents was slightly but significantly greater for HI that, the other hay varieties. 2) The LPP disappearance rates were 26.2, 25.3 and 21.7 g DM/h for H1, H2 and H3, respectively, and no statistical differences were found among the hay varieties. Appreciable changes were not observed with SPP and SOL throughout measurements for all hay varieties; however the SPP was markedly greater (p <0.05) for H2 and ill than for HI, while SOL did not differ among hay varieties. 3) The SPP passage rate (g DM/h) and effective rumen degradability (%) for HI, H2 and ill were, respectively, 9.7, 56.6; 16.9, 42.3; and 18.0, 28.9. The ruminal tum-over rate for SPP appeared to be higher for HI than for the other hay varieties.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.63-69
• /
• 2011

In this study, we report on the novel lithographic patterning method to fabricate organic thin film field effect transistors (OTFTs) based on photo and e-beam lithography with well-known silicon technology. The method is applied to fabricate pentacene-based organic field effect transistors. Owing to their solubility, sub-micron sized patterning of P3HT and PEDOT has been well established via micromolding in capillaries and inkjet printing techniques. Since the thermally deposited pentacene cannot be dissolved in solvents, other approach was done to fabricate pentacene FETs with a very short channel length (~30 nm), or in-plane orientation of pentacene molecules by using nanometer-scale periodic groove patterns as an alignment layer for high-performance pentacene devices. Here, we introduce $Al_2O_3$ film grown via atomic layer deposition method onto pentacene as a passivation layer. $Al_2O_3$ passivation layer on OTFTs has some advantages in preventing the penetration of water and oxygen and obtaining the long-term stability of electrical properties. AZ5214 and ma N-2402 were used as a photo and e-beam resist, respectively. A few micrometer sized lithography patterns were transferred by wet and dry etching processes. Finally, we fabricated micron sized pentacene FETs and measured their electrical characteristics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1038-1041
• /
• 2003

In the paper, we investigated silicon surface microstructures formed by reactive ion etching in hollow cathode system. Wet anisotropic chemical etching technique use to form random pyramidal structure on <100> silicon wafers usually is not effective in texturing of low-cost multicrystalline silicon wafers because of random orientation nature, but High density hollow cathode plasma system illustrates high deposition rate, better film crystal structure, improved etching characteristics. The etched silicon surface is covered by columnar microstructures with diameters form 50 to 100nm and depth of about 500nm. We used $SF_{6}$ and $O_{2}$ gases in HCP dry etch process. This paper demonstrates very high plasma density of $2{\times}10^{12}$ $cm^{-3}$ at a discharge current of 20 mA. Silicon etch rate of 1.3 ${\mu}s/min$. was achieved with $SF_{6}/O_{2}$ plasma conditions of total gas pressure=50 mTorr, gas flow rate=40 sccm, and rf power=200 W. Our experimental results can be used in various display systems such as thin film growth and etching for TFT-LCDs, emitter tip formations for FEDs, and bright plasma discharge for PDP applications. In this paper we directed our study to the silicon etching properties such as high etching rate, large area uniformity, low power with the high density plasma.

• Membrane and Water Treatment
• /
• v.1 no.3
• /
• pp.215-230
• /
• 2010

Poly(vinylidene fluoride-co-hexafluoropropylene), PVDF-HFP, hollow fiber membranes were prepared by the dry/wet spinning technique using different polyethylene glycol (PEG) concentrations as non-solvent additive in the dope solution. Two different PEG concentrations (3 and 5 wt.%). The morphology and structural characteristics of the hollow fiber membranes were studied by means of optical microscopy, scanning electron microscopy, atomic force microscopy (AFM) and void volume fraction. The experimental permeate flux and the salt (NaCl) rejection factor were determined using direct contact membrane distillation (DCMD) process. An increase of the PEG content in the spinning solution resulted in a faster coagulation of the PVDF-HFP copolymer and a transition of the cross-section internal layer structure from a sponge-type structure to a finger-type structure. Pore size, nodule size and roughness parameters of both the internal and external hollow fiber surfaces were determined by AFM. It was observed that both the pore size and roughness of the internal surface of the hollow fibers enhanced with increasing the PEG concentration, whereas no change was observed at the outer surface. The void volume fraction increased with the increase of the PEG content in the spinning solution resulting in a higher DCMD flux and a smaller salt rejection factor.

• Toxicological Research
• /
• v.14 no.4
• /
• pp.465-474
• /
• 1998

This study was examined on the effect of ex-vivo immunotherapy in 7, 12-dimethylbenz[a]anthracene (DMBA)-induced rat mammary carcinogenesis. Sprague-Dawley female 40 rats were divided into Jour groups. As a positive control, Group I was intubated with DMBA, 5 mg /100 g body weight and single dose, at experimental onset. Group II was treated ex-vivo immunotherapy with polyinosinic-polycytidylic acid (Poly I : C) and Group III was treated with Interleukin-2 (IL-2). Group IV was negative control. All rats were sacrificed at 16 weeks after DMBA intubation. Mammary gland wet weight, dry fat free tissue weight, incidence of tumor, and the number of lobules, alveolar buds, terminal end buds, and terminal ducts were examined. Morphological changes of the mammary gland after treated with DMBA were analyzed by whole mount and histopathological method. As results, the induced mammary tumors of Group I, II and III were 60%, 33% and 0%, respectively. Histopathological types of induced-mammary tumors were adenoma, adenocarcinoma and carcinosarcoma. In analysis of the whole mount method, the number of the terminal end buds, terminal ducts and lobules were significantly lower in Group II (p<0.01) and III (p<0.01) than DMBA alone treated Group I. In microscopic observation, hyperplastic alveolar nodules were significantly lower in Group III than Group I (p<0.01). In conclusion, IL-2 had strong inhibitory effect on the mammary gland tumorigenesis induced by DMBA in rats. Whole mount method may be a useful technique to assess the mammary carcinogenesis. Moreover, hyperplastic alveolar nodules were very sensitive parameter to assess the mammary carcinogenesis.