• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.6
• /
• pp.84-97
• /
• 2016

This study was to investigate the user's thermal environments of the children's parks according to pavements and sunscreen types during periods of heat waves. The measurements were conducted at the sand pits, rubber chip pavement, shelters, and green shade ground of the two children's parks located in Jinju, Korea(Chilam: $N\;35^{\circ}11^{\prime}1.4{^{\prime}^{\prim}}$, $E\;128^{\circ}5^{\prime}31.7{^{\prime}^{\prime}}$, elevation 38m, Gaho: $N\;35^{\circ}09^{\prime}56.8{^{\prime}^{\prime}}$, $E\;128^{\circ}6^{\prime}41.1{^{\prime}^{\prime}}$, elevation 24m) over three days during 11-13, August, 2016. The highest ambient air temperatures at the Jinju Meteorological Office during the three measurement days were $35.9{\sim}36.8^{\circ}C$, which corresponded with the extremely hot weather. A series of experiments measured air temperature, relative humidity, wind velocity, black globe temperature, and long-wave and short-wave radiation of the six directions 0.6 m above ground level. The wet bulb globe temperature(WBGT) and the universal thermal climatic index(UTCI) were used to evaluate thermal stress. Surface temperature images of the play equipment were also taken using infrared thermography. Surface temperatures of the play equipment and grounds were used to evaluate burn risk through contact with playground materials. The results showed the following. The maximum air temperatures averaged over 1-hour period for three days were $36.6{\sim}39.4^{\circ}C$. The sun shades reduced those temperatures by up to $2.8^{\circ}C$(green shade) and $1.0^{\circ}C/2.3^{\circ}C$(shelters). The minimum relative humidity values averaged over 1-hour period for three days were 44~50%. The sun shades increased those humidity values by up to 6%(green shade) and 4%/6%(shelters). The risk of heat related illness at the measurement sites of the children's parks were extreme and high in the daytime hours. The maximum WBGT values averaged over a 30-minute period for three days were $31.2{\sim}33.6^{\circ}C$. The sun shades reduced those WBGT values by up to $2.4^{\circ}C$(green shade) and $0.5^{\circ}C/2.1^{\circ}C$(shelters) compared to sandpits, but would not block the risk of heat related illness in the daytime hours. The category of heat stress at the measurement sites of the children's parks were extreme and very strong in the daytime hours. The maximum UTCI values averaged over a 30-minute period for three days were $39.9{\sim}48.1^{\circ}C$. The sun shades reduced those UTCI values by up to $7.8^{\circ}C$(green shade) and $4.1^{\circ}C/8.2^{\circ}C$(shelters) compared to sandpits, but could not lower heat stress category from extreme and very strong to strong and moderate in the daytime hours. According to the burn threshold criteria when skin was in contact with playground materials, the maximum surface temperature of the stainless steels($70.8^{\circ}C$) surpassed three seconds $60^{\circ}C$ threshold for uncoated steel, that of the rubber chip($76.5^{\circ}C$) surpassed five seconds $74^{\circ}C$ threshold for the plastic, that of the plastic slide($68.5^{\circ}C$) and seats($71.0^{\circ}C$) surpassed the one min $60^{\circ}C$ threshold for plastic, respectively. The surface temperatures of shaded play equipment were lower approximately $20^{\circ}C$ than those of play equipment exposed to the sun. Therefore, sun shades can block the risk of burns in daytime hours. Because of the extreme and high risk of heat related illness and extreme and high heat stress at the children's parks during periods of heat waves, parents and administrators must protect children from the use of playgrounds. The risk of burn when contact with play equipments and grounds at the children's parks during periods of heat waves, was very high. The sun shades are essential to block the risk of burn from play equipments and grounds at the children's parks during heat waves.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.4
• /
• pp.351-358
• /
• 2008

Purpose: This study examined the recovery of the dentin-resin bonding strength, and the difference in the bonding strength after applying pH hemostatic agents at various pH. Materials and methods: Bosmin, Hemodent, Astregedent, and Visine were used as the hemostatic agents in this study. The Bosmin, Hemodent, and Astrigedent hemostatic agents are acidic, and the Visine hemostatic agent is neutral and is used as a decongestant. Ninety human molar teeth were used as the specimen. The teeth were sectioned using a diamond wheel until the dentin was exposed and wet ground by silica paper. The specimens were divided into two groups according to the hemostatic agent used. The specimens were then subdivided into 9 groups according to the application of re etching (R group) or rinsing only (N group). A commonly used resin bonding procedure was used in the control group. The resin bonding procedure was managed dentin using celluloid capsule. In addition, the shear bond strength was measured using an Instron. Results: In general, samples with the applied hemostatic agent, with the exception of Visine, had a slightly weak bond that was similar to the control group. In addition, the rinsing only (N) group had slightly weak bond that was similar to the re etching (R) group. Conclusion: The application of a hemostatic agent on the dentin surface does not affect the shear bond strength after application for a short time. In addition, rinsing only can recover the shear bond strength making other management procedures redundant, particularly re etching.

• Korean Journal of Soil Science and Fertilizer
• /
• v.8 no.2
• /
• pp.45-51
• /
• 1975

The morphological, physical, chemical, and mineralogical characteristics of planosols in Korea were studied in an effort to establish the suitabilition of the planosols for agricultural development. The Yeongog series which are planosols were established in Korea. Results from the Yeongog series are briefly as follows : 1. Morphologically, the surface soils are brown to dark brown friable loam and subsoils are of varied colors but mainly are dark brown, black and pale brown mottles. The texture of these horizons are silty clay loam with moderate to strong platy structure and clay cutans are on the ped faces. The consistences of these horizons are extremely compact and hard when moist and sticky, plastic when wet. The substrata show varied soil colors and loam to clay loam. 2. Physically, the clay content of the Yeongog soils is highest in the subsoils and gradually decreases below the subsoils. Water holding capacity and bulk desity is higher than in other mineral soils. 3. Chemically, the organic matter content is low and soil reaction ranges from very strongly to strongly acid. The cation exchange capacity is medium and base saturation a high. Active iron, easily reducible manganese and available silicate are high compared with normal soils. 4. In chemical composition of clay fraction of the Yeongog series, sesquioxide ratio, $Fe_2O_3$, $K_2O$ and MgO are high. The cation exchange capacity of the clay fraction is also very high. 5. The clay minerals in Yeongog series are mainly kaoline, vermiculite with Al interlayers and illite. The quarts, primary minerals are in the Yeongog soils. 6. These soils are formed in a warm, humid climate under native grasses on the terraces and rolling or hilly footslopes. In soil classification, the Yeongog soils are classified planosols with claypan. According to 7th approximation system in U.S.A., the Yeongog series are classified as Fragiudalfs because they have an argillic horizon, a hard pan and a high base saturation which is more than 35 percent and classified as Eutric Planosols by FAO/UNESCO classification system.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Korean Journal of Soil Science and Fertilizer
• /
• v.23 no.2
• /
• pp.100-106
• /
• 1990

Changes in soil water potential and soil water content, evapotranspiration and water use efficiency during red-pepper cultivation were investigated under different mulching conditions(Non-mulching, Transparent vinyl and Black vinyl mulching) in a sandy loam soil for 1982 & 1983. The soil water potential up to 20cm depth for transparent vinyl mulching were higher than those of non-mulching condition until the rain free days lasted 25 days, and more than 6 weeks for black vinyl mulching. Root zone water content up to 10cm, 20cm, 30cm, and 50cm for transparent vinyl mulching were lower than those of non-mulching condition after the rain free days lasted more than 2weeks, 3weeks, 5weeks and 6weeks, respectivery. Soil water depletion of deep soil depth were more than that of surface zone for transparent vinyl mulching as the rain free days continued, whereas there was no difference to soil depth for non-mulching condition. Evapotranspiration rates under transparent vinyl mulching condition were higher in dry season but lower in wet season than those of non-mulching condition. Total evapotranspiration during growing season of mulching with transparent or black vinyl was not siginficantly different from that of non-mulching condition, whereas water use efficiency was increased by vinyl mulching with not only whole mulching but also top mulching.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.559-571
• /
• 2017

This study was conducted to determine the adhesive performances of plywoods affected by layering direction and the amounts of thermoplastic films. The face and back layers of veneer were hardwood species (Mixed light hardwood) and core layer veneer was radiata pine (Pinus radiata D. Don). Thermoplastic film used as adhesive were polypropylene (PP) film and polyethylene (PE) film. Thermal analysis and tensile strength were investigated on each films. As a result, the melting temperature of PP and PE films were $163.4^{\circ}C$ and $109.7^{\circ}C$, respectively, and the crystallization temperature were $98.9^{\circ}C$ and $93.6^{\circ}C$, respectively. Tensile strength and elongation of each films appeared higher on the width direction than length direction. Considering the characteristics of the thermoplastic films, the test for the amount of film used was carried out by layering film to the target thickness on veneer. The effecting of layering direction of film on plywood manufacturing was conducted by laminating in the length and width directions of the film according to the grain direction of veneer. Tensile-shear strength of plywood in wet condition was satisfied with the quality standard (0.7 MPa) of KS F 3101 when the film was used over 0.05 mm of PP film and over 0.10 mm of PE film. Tensile-shear strength of plywood after cyclic boiling exceeded the KS standard when PP film was used 0.20 mm thickness. Furthermore, higher bonding strength was observed on a plywood made with width direction of film according to grain direction of veneer than that of length direction of film. Based on microscopic analysis of the surface and bonding line of plywood, interlocking between veneers by penetration of a thermoplastic film into inner and cracks were observed.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.3
• /
• pp.143-150
• /
• 1993

To gain the basic informations on soil management practices by determination of the differences of soil genetic characteristics and the contents of soil moisture due to slope aspects of hilly land, this study was conducted at 1992 on sweet persimmon orchard soils derived from porphyry in southern of Korea. The results obtained were summarized as follows. The soils studied were belong to fine loamy family. The degree of soil development was greater in the north than other slope aspects and the solum thickness also the same. The soil chemical properties such as pH and exchangeable cations except for potassium were low generally in the orchards studied but the content of organic matter was lack in the summit and south aspect. The contents of Fe oxide and extractable Al were higher in the subsurface than surface. Fe, Al and clay indexes which indicate relative intensity of B horizon development were higher in the side slope than summit and the highest in the north slope. The rate of solum to B horizon was higher as about 1.5 for summit and west aspect which had thiner B horizon thickness compared to other aspect. North and west aspect had certainly more amount of soil water at drought season than other slope aspects and was lower the difference of soil water between the drought and wet seasons. Therfore, the soil management such as erosion control and irrigation at drought season should be practices differently due to slope aspect and soil chararteristics in the sloped land.

• Korean Journal of Ecology and Environment
• /
• v.38 no.1 s.110
• /
• pp.45-53
• /
• 2005

The environmental change of Yong-nup in Mt. Dae-Am, which is located at the northern part of Kangwon-Do, Korea, was assesed with peat sedimentary carbon and nitrogen isotope analysis. The surface layer of the peat (0 ${\sim}$ 5 cm) was 190 year BP, and the middle layers (30 ${\sim}$ 35 cm and 50 ${\sim}$ 55 cm) were 870 year BP and 1900 year BP, respectively. Bulk sedimentation rate was estimated to be about 0.4 mm $year^{-1}$ for 0 cm to 30 cm and 0.15 mm $year^{-1}$ for 35 cm to 50 cm. The $^{14}C$ age of the bottom sediment (75 ${\sim}$ 80 cm) collected and measured in this study was about 1900 year BP, although it was measured that the $^{14}C$ of the lowest bottom sediment in Yong-nup was 4105 ${\pm}$ 175 year BP (GX-23200). Since the $^{14}C$ ages for 50 ${\sim}$ 55 cm and 75 ${\sim}$ 80 cm layers were almost the same as 1890 ${\pm}$ 80 fear BP (NUTA 5364) and 1850 ${\pm}$ 90 year BP (NUTA 5462), respectively, we have estimated that the deep layers (55 ${\sim}$ 80 cm) in the high moor were the original forest soil. The low organic C and N contents in the deeper layers supported the inference. The sediment of 50 ${\sim}$ 55 cm layer contains much sandy material and showed very low organic content, suggesting the erosion (flooding) from the surrounding area. In this context, the Yong-nup, high moor, of Mt. Dae-Am, might have developed to the sampling site at about 1900 year BP. The ${\delta}^{13}C$ values of organic carbon and the ${\delta}^{15}N$ values of total nitrogen in the peat sediments fluctuated with the depths. The profile of ${\delta}^{13}C$ may indicate that the Yong-nup of Mt. Dae-Am have experienced the dry-wet and cool-warm period cycles during the development of the high moor. The ${\delta}^{15}N$ may indicate that the nitrogen cycling in the Yong-nup have changed from the closed (regeneration depending) system to the open (rain $NO_3\;^-$ and $N_2$ fixation depending) system during the development of the high moor.

• Economic and Environmental Geology
• /
• v.35 no.1
• /
• pp.25-41
• /
• 2002

In order to investigate the hydrogeochemical characteristics and contamination of dissolved major ions and heavy metals in the Tancheon River, river water and sediment samples were collected at 18 locations, along a distance of 69 km, between Yongin-si in Kyunggi-do and Samsung-dong in Seoul on October in 2000 and April in 2001. After appropriate sample preparation, waters were analyzed for the dissolved constituents and sediments. The pH values of river waters were in the range of 7.0 to 9.3 and could be plotted in the area of surface environment. The level of $Ca^{2+}$, , CI-, sol-, N0$_{3}$ and HC0$_{3}$ in the Tancheon River were higher than those in world average river water. Most of dissolved constituents in the river waters increased toward downstream from upstream. In particular, high concentrations of Zn2+, Na$_{+}$, CI$^{-}$, SO$_{4}^{2-}$ and N03- were found near densely residential areas and the Sungnam waste water treatment plant. The relative ion enrichment was caused by the inflow of local domestic and industrial sewages. Also, Ca2+ and HC03- concentrations were enriched in the middle of the Tancheon River due to the dissolution of cements. This indicates that the apartment complexes were built on a large scale in the upriver since these ten years and large amounts of construction materials such as cements were flowed into the Tancheon River. Concentrations of heavy metals (Mn, Cd, Cu, Pb, Zn) in sediments from the Tancheon River exceeded the lower limit of tolerence level in bottom sediment established by the Ontario Ministry of the Environment (OME) of Canada. In particular, these metals were highly elevated in sediment (TSM-12) collected from near the Sungnam waste water treatment plant. Heavy metals were higher enriched in sediments collected from dry period rather than wet period.

• Economic and Environmental Geology
• /
• v.36 no.6
• /
• pp.481-490
• /
• 2003

The objectives of this study are (1) to determine the extent and degree of As contamination of the water and sediments influenced by mining activity of the abandoned Au-Ag mines, (2) to examine As speciation In contaminated water, (3) to monitor variation of As contamination in water system throughout the dry and wet seasons, and (4) to investigate the As chemical form in the sediments through the sequential extraction analyses. Natural water(mine water, surface water and groundwater) and sediments were collected in six abandoned Au-Ag mine(Au-bearing quartz veins) areas. The contamination level of As in mine water of the Dongil(524${\mu}m$/L) is more higher than the tolerance level(500 ${\mu}m$/L) for waste water of mine area in Korea. Elevated levels of As in stream water were also found in the Dongil(range of 63.7∼117.6 ${\mu}m$/L.) and Gubong(range of 56.1∼62.9 ${\mu}m$/L) mine areas. Arsenic contamination levels in groundwater used by drinking water were more significant in the Dongil(11.3∼63.5 ${\mu}m$/L), Okdong(0.2∼68.9 ${\mu}m$/L) and Gubong(2.0∼101.0${\mu}m$/L) mine areas. Arsenate[As(V), $H_2AsO_4^-$] is more dominant than arsenite[As(III), $H_3AsO_3$] in water system of the most mine areas. The concentration ratios of As(III) to As(total), however, extend to the 95% in stream water of the Okdong mine area and 70∼82% in groundwater of the Okdong and Dongjung mine areas. As a study of seasonal variation in the water system, relatively high levels of As from the dongil mine area were found in April rather than in September. Sequential extraction analysis showed that As was predominantly present as coprecipitated with Fe hydroxides from sediment samples of the Dongjung and Gubong mine(35.9∼40.5%), which indicates its possibility of re-extraction and inducing elevated contamination of As in the reductive condition. In sediments from the Dongil, Okdong and Hwachon mine area, high percentage(55.2∼83.4%) of As sulfide form was found.