• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.106-112
• /
• 1990

The progress of oxidation of a porous silicon layer(PSL) was studied by examining the temperature dependence of the oxidation and the infrared absorption spectra. Thick OPSL(oxidized porous silicon layer). which has the same properties as thermal $SiO_{2}$ of bulk silicon, is formed in a short time by two steps wet oxidation of PSL at $700^{\circ}C$, 1 hr and $1100^{\circ}C$, 1 hr. Etching rate, breakdown strength of the OPSL are strongly dependent on the oxidation temperature, oxidation atmosphere. And its breakdown field was ${1\MV/cm^-2}$ MV/cm The oxide film stress was determined through curvature measurement using a dial gauge. During oxidation at temperature above $1000^{\circ}C$ in dry $O_{2}$, stress on the order of ${10^9}\dyne/{cm^2}{-10^10}\dyne/{cm^2}$ are generated in the OPSL.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.344-344
• /
• 2014

Transparent amorphous oxide semiconductors such as a In-Ga-Zn-O (a-IGZO) have advantages for large area electronic devices; e.g., uniform deposition at a large area, optical transparency, a smooth surface, and large electron mobility >10 cm2/Vs, which is more than an order of magnitude larger than that of hydrogen amorphous silicon (a-Si;H).1) Thin film transistors (TFTs) that employ amorphous oxide semiconductors such as ZnO, In-Ga-Zn-O, or Hf-In-Zn-O (HIZO) are currently subject of intensive study owing to their high potential for application in flat panel displays. The device fabrication process involves a series of thin film deposition and photolithographic patterning steps. In order to minimize contamination, the substrates usually undergo a cleaning procedure using deionized water, before and after the growth of thin films by sputtering methods. The devices structure were fabricated top-contact gate TFTs using the a-IGZO films on the plastic substrates. The channel width and length were 80 and 20 um, respectively. The source and drain electrode regions were defined by photolithography and wet etching process. The electrodes consisting of Ti(15 nm)/Al(120 nm)/Ti(15nm) trilayers were deposited by direct current sputtering. The 30 nm thickness active IGZO layer deposited by rf magnetron sputtering at room temperature. The deposition condition is as follows: a rf power 200 W, a pressure of 5 mtorr, 10% of oxygen [O2/(O2+Ar)=0.1], and room temperature. A 9-nm-thick Al2O3 layer was formed as a first, third gate insulator by ALD deposition. A 290-nm-thick SS6908 organic dielectrics formed as second gate insulator by spin-coating. The schematic structure of the IGZO TFT is top gate contact geometry device structure for typical TFTs fabricated in this study. Drain current (IDS) versus drain-source voltage (VDS) output characteristics curve of a IGZO TFTs fabricated using the 3-layer gate insulator on a plastic substrate and log(IDS)-gate voltage (VG) characteristics for typical IGZO TFTs. The TFTs device has a channel width (W) of $80{\mu}m$ and a channel length (L) of $20{\mu}m$. The IDS-VDS curves showed well-defined transistor characteristics with saturation effects at VG>-10 V and VDS>-20 V for the inkjet printing IGZO device. The carrier charge mobility was determined to be 15.18 cm^2 V-1s-1 with FET threshold voltage of -3 V and on/off current ratio 10^9.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.287.1-287.1
• /
• 2016

Three-dimensional (3-D) semiconductor nanoarchitectures, including nano- and micro- rods, pyramids, and disks, are emerging as one of the most promising elements for future optoelectronic devices. Since these 3-D semiconductor nanoarchitectures have many interesting unconventional properties, including the use of large light-emitting surface area and semipolar/nonpolar nano- or micro-facets, numerous studies reported on novel device applications of these 3-D nanoarchitectures. In particular, 3-D nanoarchitecture devices can have noticeably different current spreading characteristics compared with conventional thin film devices, due to their elaborate 3-D geometry. Utilizing this feature in a highly controlled manner, color-tunable light-emitting diodes (LEDs) were demonstrated by controlling the spatial distribution of current density over the multifaceted GaN LEDs. Meanwhile, for the fabrication of high brightness, single color emitting LEDs or laser diodes, uniform and high density of electrical current must be injected into the entire active layers of the nanoarchitecture devices. Here, we report on a new device structure to inject uniform and high density of electrical current through the 3-D semiconductor nanoarchitecture LEDs using metal core inside microtube LEDs. In this work, we report the fabrications and characteristics of metal-cored coaxial $GaN/In_xGa_{1-x}N$ microtube LEDs. For the fabrication of metal-cored microtube LEDs, $GaN/In_xGa_{1-x}N/ZnO$ coaxial microtube LED arrays grown on an n-GaN/c-Al2O3 substrate were lifted-off from the substrate by wet chemical etching of sacrificial ZnO microtubes and $SiO_2$ layer. The chemically lifted-off layer of LEDs were then stamped upside down on another supporting substrates. Subsequently, Ti/Au and indium tin oxide were deposited on the inner shells of microtubes, forming n-type electrodes of the metal-cored LEDs. The device characteristics were investigated measuring electroluminescence and current-voltage characteristic curves and analyzed by computational modeling of current spreading characteristics.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.52-59
• /
• 2022

Calcium silicate based cement (CSC) is a low-carbon cement that emits less CO₂ by up to 70% compared to ordinary Portland cement during its manufacture. Most developed countries have commercialized CSC, whereas Korea is still investigating the manufacturing characteristics and basic properties of CSC. This paper provides a review of methods for manufacturing CSC using domestic raw materials and discusses the possibility of CSC localization based on an evaluation of the basic physical properties of manufactured CSC. The experimental results of this study indicate that the primary mineral components of CSC were CS, C₃S₂ C₂S, and unreacted SiO₂. This suggests the possibility of manufacturing CSC using domestic raw materials that exhibit mineral compositions similar to that of theoretical CSC. The compressive strength of CSC mortar is less than 1MPa at the age of 7 d under wet curing. This implies that hydration does not affect the property development of CSC mortar. Meanwhile, during carbonation curing, the compressive strength is 56 MPa or higher after 7 d, which indicates excellent early strength development. Furthermore, results of Thermogravimetric Analysis Differential scanning calorimetry (TG/DSC) show that a significant amount of CaCO₃ is formed, which is consistent with the results of previous studies. This implies that carbonation is associated significantly with the properties of CSC.

• Journal of Chest Surgery
• /
• v.34 no.9
• /
• pp.704-710
• /
• 2001

Background: Extracorporeal circulation using pump-oxygenator is an inevitable process to keep vital sign during cardiac arrest for open heart surgery. However, the diversion of blood through nonendothelialized channels appears to stimulate inflammatory response, and leukocyte activation may lead to cardiopulmonary edema. Our study evaluated the effect of leukocyte-induced cardiopulmonary edema using three different pump-oxygenator priming solutions; non-hemic crystalloid solution ; leukocyte-depleted homologous blood; non leukocyte-depleted homologous blood in priming solutions. Material and Method: Each different priming solution was used on five dogs, and the effect of leukocyte-induced cardiopulmonary edema during cardiopulmonary bypass(CPB) was evaluated. For each dog after 2 hours of exracorporeal circulation and another 4 hours of post-pump period, the dog was sacrificed and its heart and lung tissues were obtained for measuring Wet/Dry ratio. Arterial $O_2$partial pressure(PaO$_2$) and $CO_2$partial pressure(Pa$CO_2$) were checked. For the evaluation of ventilatory function, $CO_2$partial pressure difference between arterial blood (Pa$CO_2$) and exhaled air(Et$CO_2$) was measured. Result: 1. No significant difference was seen in arterial PaO$_2$and Pa$CO_2$among groups. 2. Ventilatory function evaluated by Pa$CO_2$and Et$CO_2$showed no significant difference between non-hemic and blood-mixed priming solution (P<0.05). 3. Cardiac and lung Wet/Dry ratios were remarkedly lower in the leukocyte-depleted group. There was no significant difference between the non-hemic and blood-mixed groups. Conclusion: Based upon this result, we concluded that the leukocyte depletion from homologous blood of CPB priming solution has a beneficial effect in reducing cardiopulmonary edema compared with non leukocyte-depleted or crystalloid priming solutions.

• Korean Journal of Plant Taxonomy
• /
• v.35 no.4
• /
• pp.313-335
• /
• 2005

Many plants take up soluble silica from the soil, and they deposit in plant tissues. Silica bodies are most commonly found in the leaf epidermis. Silica body is important factor in growth and development of plant. It help to maintain rigidity in stem and linear leaves, and its content may be correlated with resistance to fungal disease. In this study, several morphologically distinctive forms of silica bodies on Cyperaceae in Korea are recognized, which are eventually classified into two groups. Silica body type of first group (Rhynchospora, Fuirena, Scleria, Carex, Eriophorum) is A-type, which is conical in shape. Silica body type of second group (Cyperus, Scirpus, Eleocharis, Fimbristylis, Kyllinga, Bulbostylis, Lipocarpha) is B-type, which is conical in shape with numerous satellite body. These types are consistent enough to use as characters in taxonomic studies within genus. Silica body type may be associated with habitat: the species in dry region have A-type, whereas the species in wet region have B-type. These results suggested that shapes and presence or absence of silica body might be valuable to systematic analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.86-86
• /
• 2010

Micro- and nanoscale texturing and control of surface energy have been considered for superhydrophobicity on polymer and silicon. However these surfaces have been reported to be difficult to meet the robustness and transparency requirements for further applications, from self cleaning windows to biochip technology. Here we provided a novel method to fabricate a nearly superhydrophobic soda-lime glass using two-step method. The first step involved wet etching process to fabricate micro-sale patterns on soda-lime glass. The second step involved application of $SiO_x$-incorporated DLC to generate high intrinsic contact angle on the surface using chemical vapor deposition (CVD) process. To investigate the effect of surface roughness, we used both positive and negative micro-scale patterns on soda-limeglass, which is relatively hard for surface texturing in comparison to quartz or Pyrex glasses due to the presence of impurities, but cheaper. For all samples we tested the static wetting angle and transparency before and after 100 cycles of wear test using woolen steel. The surface morphology is observed using optical and scanning electron microscope (SEM). The results shows that negative patterns had a greater wear resistance while the hydrophobicity was best achieved using positive patterns having static contact angle up to 140 deg. with about 80% transparency. The overall experiment shows that positive patterns at etching time of 1 min shows the optimum transparency and hydrophobicity. The optimization of micro-scale pattern to achieve a robust, transparent, superhydrophobic soda-lime glass will be further investigated in the future works.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1042-1047
• /
• 2002

The sedimentation characteristics of ceramic fiber were analyzed when viscosity of the slurry for ceramic paper formation was varied and zeta potential change and degree of dispersion with pH were studied as well. The proper viscosity of the slurry for dispersion of fibers was between 28 and 31 cps. Zeta potential of the slurry was sensitively changed with pH adjustment and showed maximum value of -35~-36 mV at ph 7.5~9.5, which indicated better dispersion of ceramic fiber as zeta potential of the slurry was increased. The sedimentation rate of ceramic fiber in a slurry was reported minimum at the maximum zeta potential. Water content of the casted paper should be lower than 83% after vacuum dehydration for retention of binder and lower than 62% after press rolling for wet paper handling. The obtained ceramic paper had tensile strength and basis weight, $102 kgf/cm^2$ and $98 g/m^2$, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.416-417
• /
• 2013

최근 질화물계 발광다이오드(light emitting diode, LED) 소자는 핸드폰, 스마트 TV 등의 디스플레이 분야와 실내외조명, 감성조명, 특수조명 등의 조명분야에 그 응용분야가 급속히 확대되고 있다. 이러한 LED 소자는 에너지 절감과 친환경에 장점을 가지고, 가까운 미래에 조명시장을 대체할 것으로 예상된다. 이를 만족하기 위해서는 현재보다 더 높은 효율을 갖는 LED 개발이 요구되어지고 있는 상황이다. 일반적으로 질화물계 LED 소자의 효율은 내부양자 효율, 광추출 효율 등으로 나타낼 수 있다. 내부 양자효율은 성장된 결정의 질의 개선 및 다층의 이종접합 또는 다중양자우물 구조와 같이 활성층의 캐리어 농도를 높이는 접합구조로 설계되어 80% 이상의 효율을 나타낸다. 그러나 광추출 효율은 이에 미치지 못하고 있다. 이는 반도체 재료의 높은 굴절률로 인하여 빛이 외부로 탈출하지 못하고 내부로 반사되거나 물질 안에서 흡수가 일어나기 때문이다. 따라서 이러한 문제를 해결하기 위해 많은 연구 그룹들은, 표면에 패턴 형성하여 빛의 전반사를 줄여 그 효율을 올리는 연구결과를 보고하고 있다. 대표적인 방법으로는 wet etching, 전자빔 리소그라피, 나노임프린트 리소그라피, 레이저 홀로 리그라피, 나노스피어 리소그라피 등이 사용되고 있다. 이 중, 나노스피어 리소그라피는 폴리스틸렌 혹은 실리카 등과 같은 나노 크기의 bead를 사용하여 반도체 기판 표면에 단일층으로 고르게 코팅한 마스크로 사용하여 패턴을 주는 방법이다. 이 방법의 장점으로는 대면적에 균일한 패턴을 형성할 수 있고, 공정비용이 저렴하여 양산하기에 적합하다는 특징이 있다. 나노스피어 리소그라피를 통해서 표면에 생성된 패턴 모양의 각도에 따라서, 식각되는 깊이에 변화에 따라 실험한 결과들은 있지만, 아직까지 크기가 다른 나노입자들의 마스크 이용하여 형성된 패턴 밀도에 따른 광 추출 효과에 대한 연구가 많이 미흡하다. 따라서 본 연구에서는 다양한 크기의 실리카로 패턴을 형성시켜 패턴 밀도에 대한 광추출 효율의 효과에 대해서 조사하였다. 실험 방법으론, DI, 에탄올, TEOS, 암모니아의 순서대로 그 혼합 비율을 조정하여 100, 250, 500 nm 크기의 나노입자를 합성하였고 이것을 질화물계 LED의 표면 위에 단일층으로 스핀코팅 방법을 통해 코팅을 하였다. 그 후 ICP-RIE 방법으로 필라 패턴을 형성하였는데, 그 결과 100 nm SiO2 입자를 이용한 경우 $4.5{\times}10^9$/$cm^2$, 250 nm의 경우 $1.4{\times}10^9$/$cm^2$, 500 nm의 경우 $0.4{\times}10^9$/$cm^2$의 패턴의 밀도를 보여주었다(Fig. 1). 패턴의 밀도에 따라 전계광학적 특성을 확인하여 보았는데, 그 결과는 평평한 표면과 비교하였을 때 100 nm에서 383%, 250 nm에서는 320%, 500 nm에서는 244% 상승하는 결과를 보여주었다(Fig. 2). 이번 실험을 통해서 LED의 광추출 효율은 표면 모양과 깊이 뿐 아니라 밀도가 커질수록 그 효율이 올라간다는 사실을 알 수 있었다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.34 no.4
• /
• pp.269-274
• /
• 2008

In this study we successfully altered the structural characteristics of the mica surface and were able to control oil-absorption by using the microwave enhanced etching (MEE) technique, which has originally been used in semiconductor industry. When microwave energy is applied to the mica, the surface of the mica is etched in a few minutes. As the result of etching, oil-absorption of the mica was enhanced and surface whiteness was improved by modifying the silicon dioxide layer. Additionally, the high whiteness was maintained even though the etched mica absorbed the sebum or sweat. The surface modification of mica was performed by microwave irradiation after the treatment of hydrofluoric acid. The degree of etching was regulated by acid concentration, irradiation time, the amount of energy and slurry concentration. The surface morphology of the etched mica appears to be the shape of the 'Moon'. The characteristics of surface area and roughness were examined by Brunauer-Emmett-Teller (BET) surface area analysis, atomic force microscopy (AFM), scanning electron microscopy (SEM), spectrophotometer and goniophotometer.