• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.12
• /
• pp.1048-1054
• /
• 2003

In laser surface hardening processes, the geometrical parameters such as the depth and the width of a hardened layer can be utilized to assess the hardened layer quality. However, accurate monitoring of the geometrical parameters for on-line process control as well as for on-line quality evaluation is very difficult because the hardened layer is formed beneath a material surface and is not visible. Therefore, temperature monitoring of a point of specimen surface has most frequently been used as a process monitoring method. But, a hardened layer depends on the temperature distribution and the thermal history of a specimen during laser surface hardening processing. So, this paper describes the estimation results of the geometric parameters using multi-point surface temperature monitoring. A series of hardening experiments were performed to find the relationships between the geometric parameters and the measured temperature. Estimation results using a neural network show the enhanced effectiveness of multi-point surface temperature monitoring compared to one-point monitoring.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.4
• /
• pp.312-317
• /
• 1999

An inflection point on a curve is a point where the curvature vanishes. An inflection point is useful for various geometric operations such as the approximation of curves and intersection points between curves or curve approximations. An inflection point on planar Bezier curves can be easily detected using a hodograph and a derivative of hodograph, since the closed from of hodograph is known. In the case of rational Bezier curves, for the detection of inflection point, it is needed to use the first and the second derivatives have higher degree and are more complex than those of non-rational Bezier curvet. This paper presents three methods to detect inflection points of rational Bezier curves. Since the algorithms avoid explicit derivations of the first and the second derivatives of rational Bezier curve to generate polynomial of relatively lower degree, they turn out to be rather efficient. Presented also in this paper is the theoretical analysis of the performances of the algorithms as well as the experimental result.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.155-161
• /
• 2002

This paper presents a maximum power point tracking algorithm for Photovoltaic array using only instantaneous output current information. The conventional Hill climbing method of peak power tracking has a disadvantage of oscillations about the maximum power point. To overcome this problem, we have developed an algorithm that will estimate the duty ratio corresponding to maximum power operation of solar cell. The estimation of the optimal duty ratio involves, finding the duty ratio at which integral value of output current is maximum. For the estimation, we have used the well know Lagrange's interpolation method. This method can track maximum power point quickly even for changing solar isolation and avoids oscillations after reaching the maximum power point.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.127-134
• /
• 2007

Presented in the paper is an algorithm to generate a section curve by slicing a point cloud including tens of thousands of points. Although, there have been previous research results on the slicing problem, they are quite sensitive on the density variations of the point cloud, as well as on the local noise in the point cloud. To relive the difficulties, three technological requirements are identified; 1) dominant point sampling, 2) avoiding local vibration, and 3) robustness on the density changes. To satisfy these requirements, we propose a new slicing algorithm which is based on a node-sphere diagram. The algorithm has been implemented and tested with various examples.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.4
• /
• pp.31-38
• /
• 1993

For efficient irrigation of structured horiculture and upland crops, a new technique of drip irrigation using the turbo-tape for Autumn Chinese cabbage was developed. The turbo-tape worked well, and based on this study The following results were obtained ; 1. The emission uniformity of the turbo-tape was very good with a uniformity coefficient of 92.5%. 2. Starting point of irrigation at 80% of the wilting point was better than at the wilting point itself. 3. The irrigation amounts for the Autumn Chinese cabbage cultured ranged 315 to 470mm depending upon the irrigation methods, turbo-tape irrigation method could conserve irrigation water about 37% compared to the furrow irrigation method. 4. Average yields were 2, 430g when the starting point of irrigation was at the wilting point, while 2, 680g when it was at 80% of the wilting point.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.9
• /
• pp.768-778
• /
• 2003

Numerical analysis has been carried out to investigate laminar convective heat transfer in a tube for supercritical water near the thermodynamic critical point. Fluid flow and heat transfer are strongly coupled due to large variations of thermodynamic and transport properties such as density, specific heat, viscosity, and thermal conductivity near the critical point. Heat transfer characteristics in the developing region of the tube show transition behavior between liquid-like and gas-like phases with a peak in heat transfer coefficient distribution near the pseudocritical point. The peak of the heat transfer coefficient depends on pressure and wall heat flux rather than inlet temperature and Reynolds number, Results of the modeling provide convective heat transfer characteristics including velocity vectors, temperature, and the properties as well as the heat transfer coefficient. The effect of proximity to the critical point is considered and a heat transfer correlation is suggested for the peak of Nusselt number in the tube.

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.769-775
• /
• 2019

The tensile strength of irradiated 3C-SiC, SiC with artificial point defects, SiC with symmetric tilt grain boundaries (GBs), irradiated SiC with GBs are investigated using molecular dynamics simulations at 300 K. For an irradiated SiC sample, the tensile strength decreases with the increase of irradiation dose. The Young's modulus decreases with the increase of irradiation dose which agrees well with experiment and simulation data. For artificial point defects, the designed point defects dramatically decrease the tensile strength of SiC at low concentration. Among the point defects studied in this work, the vacancies drop the strength the most seriously. SiC symmetric tilt GBs decrease the tensile strength of pure SiC. Under irradiated condition, the tensile strengths of all SiC samples with grain boundaries decrease and converge to certain value because the structures become amorphous and the grain boundaries disappear after high dose irradiation.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.250-257
• /
• 2005

Large eddy simulation{LES) methodology used to model a bluff-body stabilized non-reacting flow. The LES solver was implemented on parallel computer consisting 16 processors. To verify the capability of LES code, the results was compared with that of Reynolds Averaged Navier-Stokes(RANS) using $k-{\epsilon}$ model as well as experimental data. The results showed that the LES and RANS qualitatively well predicted the experimental results, such as mean axial, radial velocities and turbulent kinetic energy. However, in the quantitative analysis, the LES showed a better prediction performance than RANS. Specially, the LES well described characteristics of the recirculation zones, such as air stagnation point and jet stagnation point. Finally, the unsteady phenomena on the Bluff-body, such as the transition of recirculation region and vorticity, was examined with LES methodology.

• The Journal of Korean Physical Therapy
• /
• v.22 no.1
• /
• pp.83-90
• /
• 2010

Purpose: This study aimed to determine the degree of job stress and self-esteem of physical therapists as well as the correlation between the two variables. Method: This study targeted 218 physical therapists of Busan City, and was carried out from July 16 to August 6, 2009 as survey research. A structured questionnaire referring to advance researches was used as a research tool. Job stress symptoms were measured one a 5 point scale, the higher the point total, the higher the job stress. Self-esteem was measured on a 4 point scale, the higher the point total, the lower the self-esteem. After data collection we determined descriptive statistics, and did reliability analysis, factor analysis, Spearman's correlation analysis, and regression analysis. Results: Reliability analysis indicated that reliability for the job stress questionnaire was 0.93 and for the self-esteem was 0.83. The average job stress score of physical therapists was 1.19 points which was not high. The average self-esteem score was 1.76 points, whichwas high. It appeared that the higher the self-esteem, the lower the job stress. Also, self-esteem had an influence on psychological symptoms among job stress factors. Conclusion: Job stress and self-esteem of physical therapists are well-correlated and influence each other. Accordingly, self-esteem can be used as a variable for adjusting job stress of physical therapists.

• Korean Journal of Food Science and Technology
• /
• v.22 no.5
• /
• pp.582-589
• /
• 1990

A method for application of the equivalent time and temperature point for estimating kinetic parameters was proposed. The feasibility of the method was demonstrated with both theoretical and empirical kinetic data. The theoretical kinetic data were obtained from the arbitrarily chosen time-temperature data for three chemical reactions whose kinetics are well established. The experimental kinetic data were obtained for the acid (0.0005 N HCl) catalyzed hydrolysis of sucrose(2%). The activation energy and the frequency factor determined by the proposed method were $104.74{\pm}1.87kJ/mol\;and\;5.62{\times}10^{14}\;hr^{-1}$ respectively and the results agreed well with those obtained by a different method of kinetic parameter estimation, i.e. the linearly increasing temperature method.