• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.116-118
• /
• 2001

We propose an implicit numerical implementation for Leblond's transformation plasticity constitutive equations , which are widely used in welded steel structure. We apply Euler backward scheme rule to integrate the equations and determine the consistent tangent modulus. The implementation may be used with updated Lagrangian formulation. we test a simple butt-welding process to compare with SYSWELD and discuss the accuracy.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.365-374
• /
• 2004

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. That is a cause of decreasing the durability of structure. In order to solve these problems, welding repair and strengthening methods can be considered. In general, cutting and welding procedure is carried out during the repair welding. Therefore, the investigation of the behavior of residual stress and deformation generated by cutting and welding is very important for safety of structure. Residual stress and deformation produced by gas cutting and arc welding were analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular direction of the cutting line and welding line was analyzed by the 2D-FEM was similar to that was analyzed by 3D-FEM. Therefore, it is possible to predict cutting and welding residual stress by 2D and 3D FEM.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.1
• /
• pp.39-45
• /
• 2014

PURPOSE. The aim of the present study was to evaluate the accuracy of three techniques for correction of cast implant bars. MATERIALS AND METHODS. Thirty cast implant bars were fabricated on a metal master model. All cast implant bars were sectioned at 5 mm from the left gold cylinder using a disk of 0.3 mm thickness, and then each group of ten specimens was corrected by gas-air torch soldering, laser welding, and additional casting technique. Three dimensional evaluation including horizontal, vertical, and twisting measurements was based on measurement and comparison of (1) gap distances of the right abutment replica-gold cylinder interface at buccal, distal, lingual side, (2) changes of bar length, and (3) axis angle changes of the right gold cylinders at the step of the post-correction measurements on the three groups with a contact and non-contact coordinate measuring machine. One-way analysis of variance (ANOVA) and paired t-test were performed at the significance level of 5%. RESULTS. Gap distances of the cast implant bars after correction procedure showed no statistically significant difference among groups. Changes in bar length between pre-casting and post-correction measurement were statistically significance among groups. Axis angle changes of the right gold cylinders were not statistically significance among groups. CONCLUSION. There was no statistical significance among three techniques in horizontal, vertical and axial errors. But, gas-air torch soldering technique showed the most consistent and accurate trend in the correction of implant bar error. However, Laser welding technique, showed a large mean and standard deviation in vertical and twisting measurement and might be technique-sensitive method.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.73-80
• /
• 2013

From broad point of view, seam tracking has been one of main issues with respect to welding automation. Several attempts have been successful for seam tracking of fixed weaving width. As a solution of the seam tracking methods for varying groove width, the visual sensors such as CCD cameras have been adopted. Although the vision sensing techniques can achieve high accuracy, the weak point is that well-prepared vision sensor environment should be required to obtain high-quality visual measurements which can be easily affected by significant noises in industrial areas. This paper proposed an alternative seam tracking algorithm for narrow groove. A special measurement device for arc voltage, in this study, is developed to enhance the reliability of the measured welding signals. Based on the developed arc sensor algorithm, an automatic weld-width tracking algorithm is also proposed, which is able to predict the weld-position more accurately. The usefulness of the automatic weld-width tracking algorithm was well verified by applying it to gas tungsten arc welding (GTAW).

• Journal of computational fluids engineering
• /
• v.18 no.4
• /
• pp.61-68
• /
• 2013

Laser welding is widely used in the industry for the advantage of small heat affected zone and short weld process time. Conduction limit welding can be used to modify the surface characteristic and it is important to identify the heat affecting area correctly for the improvement of manufacturing accuracy. Since time and length scale associated with laser welding process are extremely small, numerical study can be a useful tool. In this study, two-dimensional axi-symmetric version of energy equation with enthalpy method has been used to analyze the effect of laser input conditions on final shape by the laser welding process. The proposed numerical procedure has been benchmarked with several experimental results and compared well. The modified Marangoni and Peclet number have been introduced using controllable input variables. Simple parametric researches have been performed for high Pr number material. The results show that higher Marangoni number increase fluid mixing, thus generating convex type weld pool. On the other hand, the width of the weld pool is proportional to Peclet number.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.1
• /
• pp.41-49
• /
• 1991

A knowledge of the resdual stress distribution at circumferential weldments can normally increase the accuracy of a fracture assessment in pipe line. In this paper, we present the measurements about the residual stress distributions at three kinds of circumferential butt welded pipes using the holl drilling strain gage method. By this experiment, we have obtined the following characteristics. At the inner surface of the pipe region near the center line of welding is under high tensile residual stress. However, as the distance from the center line of welding increases, the tensile component decreases and finally becomes compressive residual stress at region far away from the center line of welding. The longitudinal residual stress at the outer surface is compressive regardless of the diameter of pipe and the circumferential stress is changed from compressive to tensile as pipe diameter increases. The results also demonstrate that the residual stress is mainly caused by self-restraint bending force in the pipe welding.

• Nuclear Engineering and Technology
• /
• v.39 no.4
• /
• pp.337-348
• /
• 2007

A fuzzy neural network model is presented to predict residual stress for dissimilar metal welding under various welding conditions. The fuzzy neural network model, which consists of a fuzzy inference system and a neuronal training system, is optimized by a hybrid learning method that combines a genetic algorithm to optimize the membership function parameters and a least squares method to solve the consequent parameters. The data of finite element analysis are divided into four data groups, which are split according to two end-section constraints and two prediction paths. Four fuzzy neural network models were therefore applied to the numerical data obtained from the finite element analysis for the two end-section constraints and the two prediction paths. The fuzzy neural network models were trained with the aid of a data set prepared for training (training data), optimized by means of an optimization data set and verified by means of a test data set that was different (independent) from the training data and the optimization data. The accuracy of fuzzy neural network models is known to be sufficiently accurate for use in an integrity evaluation by predicting the residual stress of dissimilar metal welding zones.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.267-270
• /
• 2008

Thermo-mechanical simulation of the friction stir butt welding process was performed for AA5083-H18 sheets, utilizing commercial FVM code, STAR-CCM+, which is based on Eulerian formulation. Temperature and strain rate histories along the material flow were calculated under the steady state condition and simulated temperature distributions (profiles and peak values) were compared with experiments for verification. It was found that by including proper thermal properties of the backing plate (anvil) the accuracy of the simulation results increased significantly.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.57-63
• /
• 1998

An adaptive control in the robotic GMA welding is employed to monitor information about weld characteristics and process parameters as well as to modify those parameters to hold weld quality within acceptable limits. Typical characteristics are the bead geometry, composition, microstructure, appearance, and process parameters which govern the quality of the final weld. The main objectives of this thesis are to realize the mapping characteristics of bead width through learning. After learning, the neural estimation can estimate the bead width desired form the learning mapping characteristic. The design parameters of the neural network estimator(the number of hidden layers and the number of nodes in a layer) are chosen from an estimation error analysis. A series of bead of bead-on-plate GMA welding experiments was carried out in order to verify the performance of the neural network estimator. The experimental results show that the proposed neural network estimator can predict the bead width with reasonable accuracy and guarantee the uniform weld quality.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.35-43
• /
• 1988

Welding residual stresses were calculated by two dimensional thermal elasto-plastic analysis using element method. Complicated plastic behavior during heat transfer was simulated with time. Fist, temperature distributions. To consider time varying behavior of material properties and loading and unloading processes, iterative calculation based on initial stiffness method was carried out. The method proposed by Yamata was used in time increment control which determined the accuracy of claculation. comparison with other caculated and experimental results shows fairly good agreement.