• Journal of Welding and Joining
• /
• 제17권3호
• /
• pp.71-78
• /
• 1999

The welded metal bellows is commonly manufactured by welding pairs of washer-shaped discs of thin sheet metal stamped from strip stock in thickness from 0.025 to 0.254 mm. The discs, or diaphragms, are formed with mating circumferential corrugations. In this study, the diaphragms were welded by using a CW Nd: YAG laser to form metal bellows. The bellows was fixed on a jig and compressed axially, while Cu-rings were installed between belows edges for intimate contact of edges. The difference between the inner diameter of bellows and jig shaft causes an eccentricity, while the tolerance between motor shaft and jig shaft causes a wobble type motion. A vision sensor which is based on the optical triangulation was used for seam tracking. An image processing algorithm which can distinguish the image by bellows edge from that by Cu-ring was developed. The geometric relationship which describes the eccentricity and wobble type motion was modeled. The seam tracking using the image processing algorithm and the geometric modeling was performed successfully.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.74-79
• /
• 2009

Titanium and titanium alloy can be reproduced immediately even if oxide films($TiO_2$) break apart in sea water. Therefore, since titanium demonstrates large specific strength and outstanding resistance to stress corrosion cracking, crevice corrosion, pitting and microbiologically influenced corrosion in sea water environment, it has been widely applied to heat exchanger for ships. In particular, with excellent elongation, pure titanium may be deemed as optimal material for production of heat exchanger plate which is used with wrinkles formed for efficient heat exchange. Conventional plate type heat exchanger prevented leakage of liquid through insertion of gasket between plates and mechanical tightening by bolts and nuts, but in high temperature and high pressure environment, gasket deterioration and leakage occur, so heat exchanger for LPG re-liquefaction device etc do not use gasket but weld heat exchanger plate for use. On the other hand, since welded plate cannot be separated, it is important to obtain high quality reliable welds. In addition, for better workability and production performance, lasers that can obtain weldment with large aspect ratio and demonstrate fast welding speed even in atmospheric condition not in vacuum condition are used in producing products. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through quantitative analysis of oxygen and nitrogen and measurement of hardness as fundamental experiment for the evaluation of titanium laser welding, and evaluated the welding performance and mechanical properties of butt welding. This study welded specimens in various conditions by using laser and GTA welding machine to apply edge welding to heat exchanger, and evaluated the mechanical strength through tensile stress test. As a result of tensile test, laser weldment demonstrated tensile strength 4 times higher than GTA welds, and porosity could be controlled by increasing and decreasing slope of laser power at overlap area.

• 대한기계학회논문집A
• /
• 제34권5호
• /
• pp.561-565
• /
• 2010

용접부는 일반적으로 잘 알려져 있는 바와 같이, 외력에 의한 응력 집중원(stress concentration source)이 되는 것은 물론 용접과정에서의 입열(heat input)로 인한 성분과 조직의 변화에 의해 반복하중에 대한 피로강도(fatigue strength)가 모재의 그것에 비해 훨씬 떨어져서 피로균열(fatigue crack)의 발단이 되고 있다. 따라서, 본 연구에서는 실제로 철도차량에 적용되는 가스용접 이음재 가운데 대표적인 형상시편들을 재질별로 피로실험을 수행하여 피로하중범위-피로수명(${\Delta}P-N_f$) 관계를 도출하여 비교 평가하였다. 또한, 수치 해석적 유한요소법을 이용하여 용접이음재의 응력분포를 해석한 후, 용접이음부에 발생하는 최대주응력으로 (${\Delta}P-N_f$) 관계를 $\Delta\sigma-N_f$ 관계로 재정리하였다. 이상의 결과들을 바탕으로, 가스용접이 적용된 철도차량 차체의 경제적이고 합리적인 피로설계를 위한 기초정보로 사용하고자 하였다.

• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.26-30
• /
• 2015

Hastelloy X in this study was applied in jet engine F-15 air fighter as shroud to isolate the engine from outer skin. After 15 years operation at elevated temperature the mechanical properties decreased gradually due to the precipitation of continues second phases in the grain boundaries and precipitated inside the grain. The crack happened at the edge of the shroud due to the thermal and mechanical stress from jet engine. Selective TEM analysis found that the grain boundaries consist of $M_{23}C_6$ carbide, $M_6$ Ccarbide and small percentage of sigma(${\sigma}$) phase. Furthermore, it was confirmed the nano size of ${\sigma}$ and miu (${\mu}$) phase inside the grain. In this study, it was investigated the microstructure of the degraded shroud component and HAZ of repair welded shroud. In the HAZ, it was observed the dissolution of the $M_{23}C_6$ carbides and smaller precipitates, the migration of the undissolved larger $M_{23}C_6$ carbide and $M_6$ Ccarbide. It is also observed the liquation due to the simply melt of the segregated precipitates in the grain boundaries. Interestingly, the segregated second phases which simply melt in the grain boundaries more easily happened at higher heat input welding condition. High temperature tensile test was done at $300^{\circ}C$, $700^{\circ}C$ and $900^{\circ}C$. It was obtained that the toughness of welded sample is lower compare to the non-welded sample. The solution heat treatment at $1170^{\circ}C$ for 5 minutes was suggested to obtain a better mechanical properties of the shroud. The high cycle fatigue number of the repair welded shroud shows a much lower compare to the shroud. In addition, the high cycle fatigue number at room temperature after solution heat treatment was almost double compare to the before solution heat treatment under 420-500MPa stress amplitude. However, the high cycle fatigue number of repaired welded sample was shown a much lower compare to the non- welded shroud and solution treated shroud. One of the main reasons to decrease the tensile strength and the high cycle fatigue properties of the repair welded shroud is the formation of the liquid phase in HAZ.

• The Journal of Advanced Prosthodontics
• /
• 제7권1호
• /
• pp.39-46
• /
• 2015

PURPOSE. The mechanical and interfacial characterization of laser welded Co-Cr alloy with two different joint designs. MATERIALS AND METHODS. Dumbbell cast specimens (n=30) were divided into 3 groups (R, I, K, n=10). Group R consisted of intact specimens, group I of specimens sectioned with a straight cut, and group K of specimens with a $45^{\circ}$ bevel made at the one welding edge. The microstructure and the elemental distributions of alloy and welding regions were examined by an SEM/EDX analysis and then specimens were loaded in tension up to fracture. The tensile strength (TS) and elongation (${\varepsilon}$) were determined and statistically compared among groups employing 1-way ANOVA, SNK multiple comparison test (${\alpha}$=.05) and Weibull analysis where Weibull modulus m and characteristic strength ${\sigma}_0$ were identified. Fractured surfaces were imaged by a SEM. RESULTS. SEM/EDX analysis showed that cast alloy consists of two phases with differences in mean atomic number contrast, while no mean atomic number was identified for welded regions. EDX analysis revealed an increased Cr and Mo content at the alloy-joint interface. All mechanical properties of group I (TS, ${\varepsilon}$, m and ${\sigma}_0$) were found inferior to R while group K showed intermediated values without significant differences to R and I, apart from elongation with group R. The fractured surfaces of all groups showed extensive dendritic pattern although with a finer structure in the case of welded groups. CONCLUSION. The K shape joint configuration should be preferred over the I, as it demonstrates improved mechanical strength and survival probability.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1179-1185
• /
• 2011

용접이음부의 신뢰성 확보는 구조물의 건전성과 내구성에 직접적인 영향을 미치기 때문에 점용접 이음재의 피로설계기준(fatigue design criterion)을 정하기 위해서는 정확한 응력해석과 체계적인 피로강도평가가 필요하다. 따라서 본 연구에서는 실제 전동차량 차체에 많이 적용되는 냉간 및 열간압연강판인 SPCC, SPCE, SPHE을 대상으로 기하학적 인자(geometrical factors)들을 선별해서 TS형과 CT형의 대표적인 점용접 이음재 시험편을 기본모델로 하여 인장전단하중을 가하여 피로강도 및 피로특성을 평가하고자 하였다. 그리고 피로균열의 발생과 성장 기구에 대한 영향을 분석하기위해 용접 시 발생되는 여러 가지 주요인자들 중 입열량에 의해 발생할 수 있는 용접잔류응력을 X-ray 회절법에 의해 실험적으로 해석하였다. 그리고 이러한 해석을 통하여 얻어진 결과를 중첩(superposition)함으로 해서 잔류응력을 고려했을 경우 너깃 단 최대주응력으로 피로강도를 재평가하여 합리적인 피로설계기준(fatigue design criterion)을 재정립하고자 하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 춘계학술발표 개요집
• /
• pp.13-14
• /
• 1996

High Frequency Electric Resistance Welding process has been widely used in manufacturing welded steel pipes because of its high welding speed and quality. This process utilizes the skin effect as well as the proximity effect of the high frequency current in heating the skelp edge. In this study, an analytical solution of the edge temperature was obtained based on several assumptions. The assumptions includes the expontial decay of weldingcurrent from the surface and neglect of the heat loss in the welding direction. This calculation shows a good agreement with the observations made from the high speed camera. Using tile analytical model, tile heat required as a function of the welding speed and the skelp thickness was determined. These results were compared with the experimental results obtained.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.233-236
• /
• 1999

The welding residual stress should be considered in fatigue stress analysis because it develope during the process of the electric resistance spot welding and it causes bad affect on the fatigue crack initiation and growth at nugget edge of spot welded points. Therefore the accurate estimation of residual stress is crucial. In this study, nonlinear finite element analysis on welding residual stress generated during the process of the spot welding was conducted, and their results were compared with the experimental data measured by X-ray diffraction method. From the results, it was found that welding residual stress existed as tension in the nugget center and as compression around the nugget edge.

• 소성∙가공
• /
• 제21권4호
• /
• pp.234-239
• /
• 2012

This study examines the forming properties and forming loads needed to increase the edge thickness on the external face of a plate using finite element analysis(FEA). Recently, forming optimization techniques within FEA are being extensively used in designing the optimal forming conditions for processes like forging, extrusion, rolling, and spinning. Most of these existing forming operations involve reducing the volume per unit length, but research for increasing volume per unit length is not very extensive. For this study we chose an automotive engine flywheel which is a welded assembly of a plate and a gear with each component having a different thickness. We considered a forming technique to increase the thickness in order to allow the machining of the gear directly on the external face of plate alleviating the need for a weld. To study various forming techniques, we used the finite element method with the flow stress of material and incremental forming steps. We conclude from this study that the analysis of forming properties and forming loads by using the finite element analysis and testing is useful as a method to increase the thickness per unit length.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.19-24
• /
• 2004

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power $CO_{2}$ laser. The main factor of weld quality of laser welding is gap and edge quality. This work was preformed to focus on the gap tolerance problem during laser welding. First, bead on plate welding of thin sheet was examined to investigate the effect of laser welding variables, and to obtain optimum welding condition. Butt welding was also carried out to show the effect of gap on the laser weldability of thin sheet. In order to investigate the effect of gap on formability of welded thin sheet, LDH test was caried out. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too much heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about $80{\%}$ value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.