• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.270-276
• /
• 2020

3D printing is an additive manufacturing technology that can produce complex shapes in a single process for a range of materials, such as polymers, ceramics, and metals. Recent 3D printing technology has developed to a level that enables the mass-production through an improvement of the printing speed and the continuous development of applicable materials. In this study, 3D printing technology using a laser was applied to manufacture a heat exchanger for an air compressor in a railway vehicle. First, the optimal design of the heat exchanger was carried out by focusing on weight reduction and compactness as a shape suitable for 3D printing. Based on the design derived, heat exchanger prototypes were made of AlSi10Mg alloy material by applying the SLM technique. Moreover, the manufactured prototypes were attached to an existing air compressor, and the heat exchange performance of the compressed air was tested. The test results of the 3D printed prototypes showed a heat exchange performance of approximately 80% and 85% at low and high-pressure, respectively, compared to the existing heat exchanger. From the 𝓔-NTU method results with an external cooling air condition similar to that of the existing heat exchanger, the calculated heat transfer amount of 3D printed parts showed similar performance compared to the existing heat exchanger. As a result, the 3D printed heat exchanger is lightweight with good performance.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.2 s.72
• /
• pp.195-202
• /
• 2006

Thin-walled structures are efficiently utilized an automobiles, aircraft, satellite and ship as well as needed light weight simultaneously. This paper presents new shape of automobile hood reinforcement that rotating parts as engine, transmission are protected by thin-walled structures. The automobile hood is concerned about the resonance occurs due to the frequency of the rotating parts. The hood must be designed by supporting the stiffness of design loads and considering the natural frequencies. Hence, it is sustained the stiffness and considered the vibration by resonance. It is deep related to ride. Therefore, the topology, shape and size optimization methods are used to design the automobile hood. Topology technique is applied to determine the layout of a structural component optimum size with maximized natural frequency by volume reduction. In this research, The optimal structure layout of an inner reinforcement of an automobile hood for the natural frequency of a designated mode is obtained by using topology optimization method. The optimum size and the optimum shape are determined by PLBA(Pshenichny-Lim-Belegundu-Arora) algorithm.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.6
• /
• pp.45-52
• /
• 2019

As international criteria and standards are required in the fields of design and construction, landscape performance must also be considered not only for the value of the landscape but also for providing quality assurance and sustainability. Given the lack of research on landscape performance, the present research was purposed to analyze the importance of potential assessment categories and items using an analytical network process. A list of assessment items, which is composed of 20 items and 6 categories, was derived through a literature review and a preliminary survey of 11 landscape professionals. An ANP model was established and a survey was conducted among 30 landscape practitioners to determine the weight of priorities considering the criteria. The results of ANP showed that the categories of site selection, preservation and health, and convenience had high priorities while materials had the lowest importance score. For the assessment items, a monitoring plan was the highest importance, followed by cultural/ historic preservation, management cost reduction, and natural ground areas. Despite the difficulties in quantifying landscape achievements, most respondents agreed that there needs to be an evaluation system for landscape performance in order to assure the quality and sustainability of landscape development. More research and discussion are needed to develop an assessment system for landscape performance that is applicable to Korean context.

• Journal of Korean Academy of Nursing
• /
• v.17 no.3
• /
• pp.204-217
• /
• 1987

It is generally accepted that the delivery of health care is undergoing many changes specially those related to acute, contagious disease care and to the increase of chronic illnesses which can not be cured but are controlable. The health care practitioner can not be soley responsible for the control of their clients' care. Because the clients will play a vital role in controlling their illnesses, long term participation by both the health care provider and the client is necessary. Since most individuals with hypertension do not experience signs or symptoms, the disease is difficult to detect and even when diagnosed, clients do not comply well with their hypertension regimens. The noncompliant client is at increased risk for compliants involving the heart, brain, kidney and other organs. In an effort to explore methods of increasing patient participation in and adherence to treatment programs for hypertension, the researcher used health contracting to promote self care. The research questions are; 1) Will the health contracting increase compliance in health behavior and reduce the blood pressure\ulcorner 2) If clients comply with their regimens will this reduce their blood pressure\ulcorner The research design utilized in this study was a quasi-experimental design. A purposive sample, was abtained from two churches in the 1. area, consisting of 64 clients with hypertension. The data was collected from the middle of January to the 1st of September 1985. Randomization was only of the two church groups into experimental and control groups. Compliance with health behavior related to the hypertensive regimen, blood pressure and body weight were measured, compared and analyzed. In the experimental group measurements were made 6 times; one month before the education program after education program when health contracting was done and 4 more times once a month for 4 months. In the control group measurements were made 3 times; one month before the education program after the education program, and once 4 months later. There was no health contracting. The data were analyzed by t-test, Pearson correlation and ANOVA according to purpose of the study. The result of this study may be summarized as follows: The result related to the hypothesis on the effect of health contracting are as follows: H$_1$; “The hypothesis that the experimental group, with a health contractual agreement will demonstrate increased compliance levels for health behavior than the control group” was supported(t＝-5.29, df＝62, p＝.000). H$_2$; “The hypothesis that the experimental group, with a health contractual agreement, will demonstrate a greater reduction in blood pressure than the control group” was supported (for systolic blood pressure t＝2.72, df＝62, p＝.009, for diastolic blood pressure t＝1.95, df＝62, p＝.050). H$_3$; The hypothesis that the greater the compliance of the client with health behavior the lower the client's blood pressure will be was partially supported (for systolic pressure r＝-.2981, p＝.008, for diastolic pressure r＝-.1720, p＝.087). From the examination of the results of this study it can be concluded that the interaction between the nurse and the client, contracting to define goals and reinforcing compliant behavior, leads to improved compliance with health care behaviors and thus to an increase in the effectiveness of nursing care. Further consideration need to be given to the inclusion of the concept of health contracting in primary nursing and to further research in this area.

• Journal of Acupuncture Research
• /
• v.27 no.1
• /
• pp.75-86
• /
• 2010

Objectives : We developed and proposed a guideline for safety and performance assessment of electric moxibustion apparatus (class II medical device). Methods : We drafted the guideline for safety and performance assessment of electric moxibustion apparatus by referring the existing standards, guidelines and measurement data from commercially available products. Temperature characteristics such as maximum temperature and ramp time, and physical characteristics such as weight, noise and diameter were measured. User friendliness was also evaluated for commercial devices. Results : This guideline only can be applied to the electric moxibustion apparatus where moxa is being heated by electricity for medical proposes. Maximum temperature of higher than $50^{\circ}C$ can be achieved mostly. Ramp rate of temperature seems to be reliable. Control of temperature is needed to be improved. Moxa and its derivative products seem to be regulated for reliable temperature performance for clinical application. Requirements for design and development of electric moxibustion apparatus are suggested : temperature indicator, temperature control and its accuracy, safety measure, surge protection, user friendliness and instruction for use (IFU). Design recommendation of the reduction of noise level and energy loss are suggested for better products. Conclusions : We proposed a guideline for safety and performance assessment of electric moxibustion apparatus to improve the quality of relating products and aid their commercialization by aiming higher industrial competitiveness of the medical device sectors in Korea. Discussion with related institutes such as industry, academy and government is further required. Public hearings also need to be held prior to the establishment of a final guideline and standard.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.3
• /
• pp.11-25
• /
• 2023

In this study, the design and numerical analysis method of the inclined self-supported wall using cement treated soil were studied. In the case of the inclined self-supported wall, the active earth pressure decreased due to the decrease in the coefficient, Ka according to the slope (angle) and the weight decreasing effect, thereby increasing the overall stability. The wall with the slope caused a change in failure mode from overturning to sliding on the excavation side, and the optimal slope was evaluated to be about 10°. Compared to the strength reduction method, the overall stability in numerical analysis results in conservative results in limit equilibrium analysis, so it was found that this method should be attended when designing. As a result of the parameteric study, the stability on bearing capacity and compression failure did not significantly increase above the slope of 10° when the surcharge was small (about 20kPa or less). In the case of cohesion of the backfill, The results similar to numerical analysis were found to consider cohesion. It was evaluated that stability on sliding, oveturning, shear, and tension failure increases in proportion to the thickness of the wall, but there is no significant change in the stability on the bearing capacity and compressive failure regardless of the thickness of the wall above a certain angle (about 10°).

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.1
• /
• pp.93-100
• /
• 2014

The banning of the use of antibiotics as feed additive has accelerated investigations of alternative feed additives in animal production. This experiment investigated the effect of pure citric acid or acidifier blend supplementation as substitute for antibiotic growth promoters on growth performance, fecal microbial count, and humoral immunity in weaned piglets challenged with Salmonella enterica serover Typhimurium and Escherichia coli KCTC 2571. A total of 60 newly weaned piglets (crossbred, 28-d-old; average 8 kg initial weight) were randomly assigned to four dietary treatments in a completely randomized design. Dietary treatments included NC (negative control; basal diet), PC (positive control; basal diet+0.002% apramycin), T1 (basal diet+0.5% pure citric acid), and T2 (basal diet+0.4% acidifier blend). All piglets were orally challenged with 5 mL of culture fluid containing $2.3{\times}10^8$ cfu/mL of E. coli KCTC 2571 and $5.9{\times}10^8$ cfu/mL of S. typhimurium at the beginning of the experiment. The PC group showed the highest ADG and ADFI, whereas gain:feed was improved in the PC and T1 group (p<0.05). All dietary treatments showed significant reduction in fecal counts of Salmonella and E. coli, compared to NC (p<0.05), with PC being better than T1 and T2. Significant elevation in fecal Lactobacillus spp. counts was shown by treatments with T1, T2, and PC, whereas Bacillus spp. counts were increased by treatment with T1 and T2 compared to NC and PC diet (p<0.05). Serum IgG concentration was increased by T1 diet (p<0.05), whereas IgM and IgA were not significantly affected by any of the dietary treatments (p>0.05). From these above results, it can be concluded that, as alternatives to antibiotics dietary acidification with pure citric acid or acidifiers blend did not fully ameliorate the negative effects of microbial challenges in respect of growth performance and microbial environment, however improved immunity suggested further research with different dose levels.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.11
• /
• pp.1600-1607
• /
• 2014

A total of 120 finishing pigs ([Yorkshire${\times}$Landrace]${\times}$Duroc) with an average body weight (BW) of $49.72{\pm}1.72kg$ were used in 12-wk trial to evaluate the effects of protected organic acids on growth performance, nutrient digestibility, fecal micro flora, meat quality and fecal gas emission. Pigs were randomly allotted to one of three dietary treatments (10 replication pens with 4 pigs per pen) in a randomly complete block design based on their initial BW. Each dietary treatment consisted of: Control (CON/basal diet), OA1 (basal diet+0.1% organic acids) and OA2 (basal diet+0.2% organic acids). Dietary treatment with protected organic acid blends linearly improved (p<0.001) average daily gain during 0 to 6 week, 6 to 12 week as well as overall with the increase in their inclusion level in the diet. The dry matter, N, and energy digestibility was higher (linear effect, p<0.001) with the increase in the dose of protected organic acid blends during 12 week. During week 6, a decrease (linear effect, p = 0.01) in fecal ammonia contents was observed with the increase in the level of protected organic acid blends on d 3 and d 5 of fermentation. Moreover, acetic acid emission decreased linearly (p = 0.02) on d7 of fermentation with the increase in the level of protected organic acid blends. During 12 weeks, linear decrease (p<0.001) in fecal ammonia on d 3 and d 5 and acetic acid content on d 5 of fermentation was observed with the increase in the level of protected organic acid blends. Supplementation of protected organic acid blends linearly increased the longissimus muscle area with the increasing concentration of organic acids. Moreover, color of meat increased (linear effect, quadratic effect, p<0.001, p<0.002 respectively) and firmness of meat showed quadratic effect (p = 0.003) with the inclusion of increasing level of protected organic acid in the diet. During the 6 week, increment in the level of protected organic acid blends decreased (linear effect, p = 0.01) Escherichia coli (E. coli) counts and increased (linear effect, p = 0.004) Lactobacillus counts. During 12-wk of experimental trial, feces from pigs fed diet supplemented with organic acid blends showed linear reduction (p<0.001) of E. coli counts and the tendency of linear increase (p = 0.06) in Lactobacillus count with the increase in the level of organic acid blends. In conclusion, 0.2% protected organic acids blends positively affected growth performance, nutrient digestibility, fecal gas emission and meat quality in finishing pigs without any adverse effects on blood parameters.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.57-64
• /
• 2006

The crack presented in concrete structures causes a structural defect, the durability decrease, and external damages etc. Therefore, it is necessary to improve durability through the effort to control the crack. Fluosilicic acid($H_2SiF_6$) is recovered as aqueous solution which absorbs $SiF_4$ produced from the manufacturing of industrial-graded $H_3PO_4$ or HF. Generally, fluosilicates prepared by the reaction between $H_2SiF_6$ and metal salts. Addition of fluosilicates to cement endows odd properties through unique chemical reaction with the fresh and hardened cement. Mix proportions for experiment were modulated at 0.45 of water to cement ratio and $0.0{\sim}2.0%$ of adding ratio of fluosilicate salt based inorganic compound. To evaluate correlation of concrete strength and adding ratio of fluosilicate salt based inorganic compound, the tests were performed about design strength(21, 24, 27 MPa) with 0.5% of adding ratio of fluosilicate salt based inorganic compound. Applications of fluosilicate salt based inorganic compound to reduce cracks resulted from plastic and drying shrinkage, to improve durability are presented in this paper. Durability was evaluated as neutralization, chloride ion penetration depth, freezing thawing resistant tests and weight loss according reinforcement corrosion. It is ascertained that the concrete added fluosilicate salt based inorganic compound showed m ability to reduce the total area and maximum crack width significantly as compared non-added concrete. In addition, the durability of concrete improved because of resistance to crack and watertightness by packing role of fluosilicate salt based inorganic compound obtained and pozzolanic reaction of soluble $SiO_2$ than non-added concrete.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.2
• /
• pp.433-438
• /
• 2004

This study was conducted to develop a sweet pumpkin to intermediate materials for various processed foods and dried food having high quality. Factorial experiment design with three variables having three levels was adapted and response surface methodology was used to determine optimum conditions for osmotic dehydration of sweet pumpkin. The moisture content, weight reduction, moisture loss and solid gain after osmotic dehydration increased according to increasement of immersion temperature, concentration and time. The effect of concentration was more significant than that of temperature and time at given conditions. Sugar concentration and vitamin C content increased in accordance with increasement of immersion temperature, concentration and time during osmotic dehydration. Hardness was increased by increasing immersion time. The regression models showed very significant values and high correlation coefficients (R2) above 0.91, excepting hardness. The optimum condition for osmotic dehydration was 23$^{\circ}C$, 52$^{\circ}C$Brix and 80 min at the constricted conditions such as 60∼70% moisture content, above 3 mg/100 g vitamin C and more than 10 kg/$\textrm{cm}^2$ hardness.