• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.127-132
• /
• 2000

Morphological analysis of wear particles is one of useful methods for machine condition monitoring because it is well reflected in machine driving state. This paper was undertaken to apply to the condition monitoring of hydraulic piston motor. The lubricating wear test was performed under different experimental conditions using the wear test device and wear specimens of the pin on disk type was rubbed in paraffinic base oil by three kinds of lubricating materials, varying applied load, sliding distance. The four shape parameters(50% volumetric diameter, aspect, roundness and reflectivity) are used for morphological analysis of wear particles. The results showed that the four shape parameters of wear particles depend on a kind of the lubricating materials. It was capable of calculating presumed wear volume for three kinds of materials on driving time to foresee as damage condition of lubricating materials.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.319-326
• /
• 2001

The sliding wear characteristics of carbon steel castings were Investigated using a ball on disk type tester. The experiment was conducted using high carbon steel wire rods as ball material and carbon steel castings as disk material and different operating conditions, at room temperature under a lubrication and dry conditions. The results showed that the carbon steel castings appeared average wear volume Is lowed after annealing under a lubrication conditions and wear curve linear Increased. The specific wear rate of carbon steel castings Increased with wire diameter lubrication and dry also Increased 125 times In Ory. The sliding wear mechanism were Investigated due to fatigue wear lubrications and abrasive wear dries also wire Included fatigue and abrasive wear by plastic flow.

• Tribology and Lubricants
• /
• v.22 no.2
• /
• pp.73-78
• /
• 2006

The surface modification of automobile parts is of great technological importance for the improvement of corrosion resistance, wear resistance, fatigue strength and so on. Recently, research on the development of the technology of surface modification substituting 6-balance chrome process has progressively been achieved in automobile parts. Although the innovation technology for the improvement of the corrosion-resisting and wear resistant properties through post oxidation after nitrocarburising process had attracted a great attention. For this, anodically potentiodynamic polarisation testing was carried out to corrosion resistance and friction and wear experiment according to applied load and sliding distance was carried out to evaluate the wear resistance of machine structural steel with nitrocarburising and non-nitrocarburising SM45C. The presumed wear volume was calculated with the image processing far evaluation of wear resistance of two materials. The results show that the nitrocarburising had a distinguished corrosion resistance and wear resistance than non-nitrocarburising.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04a
• /
• pp.117-121
• /
• 1996

Friction and wear test for non-asbestos material against cast iron drum were carried out to investigate the friction and wear characteristics of brake system. Its friction coefficient and wear volume were measured and compared with those of asbestos friction material. The experiment. was perforated tinder room temperature and various sliding conditions. After each experiment, the sin-faces of friction materials were observed by SEM.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.109-124
• /
• 2015

This paper presents a wear analysis procedure for the journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. A journal bearing is in the mixed elastohydrodynamic (EHL) lubrication region when the shaft speed is less than the corresponding lift-off speed. Below the lift-off speed, a wear scar can form on bearing surfaces. In part 1 of this paper, we develop the appropriate formulations and the calculation procedure for the analysis. Specifically, we formulate an equation for modified film thickness in a journal bearing considering the additional wear volume. In order to obtain the modified specific wear rate induced by the modified Archard’s wear coefficient, we utilized the extended non-dimensional diagram for the specific wear rate, k, the fractional film defect coefficient, Ψ and the asperity load sharing factor, γ₂. This asperity load sharing factor is newly calculated by setting the Zhao-Maietta-Chang (ZMC) asperity contact pressure equation coupled with the central film thickness equation derived by using the ZMC asperity contact model equal to the modified central contact pressure derived by using the central (or maximum) contact pressure at the dry rough line-contact configuration. We can use the procedure introduced in this paper to determine the lifetime (or longterm) linear wear in radial journal bearings that is a result of repeated stop-start cycles.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.349-350
• /
• 2002

The friction and wear behaviors of fluorine-containing compounds such as perfluoropolyethers (PFPE), phosphazenes (X-1P), ionic liquids as lubricants for steel/seel, steel/ceramic, ceramic/ceramic were investigated using a SRV tester and a one-way reciprocating friction tester both in ball-on-disc configuration. It was found that the three fluorine-containing lubricants could reduce friction coefficient and wear volume effectively. The effectiveness of the three lubricants in reducing wear volume could be ranked as ionic liquids>X-1P>PFPE. Tests also showed that aryloxyphosphazene with polar substituent as a lubricant of steel/steel pair gave low wear, while aryloxyphosphazene with nonpolar group on the phenyl pendant led to high wear. The morphology and the tribo-chemical reaction of the worn surfaces were analyzed with a scanning electron microscope (SEM) and X-ray photoelectron spectroscope (XPS). XPS analyses illustrated the formation of iron fluoride in steel/steel system with the lubrication of both phosphazenes and ionic liquids.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.301-305
• /
• 2007

The wear particle analysis has been known as very effective method to foreknow and decide a moving situation and a damage of machine parts by using the digital computer image processing. But it was not laid down and trusted to calculate shape parameters of wear particle and wear volume. In order to apply image processing method in the foreknowledge and decision of lubricated condition, it needs to verify the reliability of the calculated data by the image processing and to lay down the number of images and the amount of wear particle in one image. In this study, the lubricated friction experiment was carried out in order to establish the optimum image capture with the SM45C specimen under experiment condition. The wear particle data were calculated differently according to the number of image and the amount of wear particle in one image.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.11
• /
• pp.1881-1888
• /
• 2003

This study show a numerical method to predict roll wear in the roll forming process. Archard's wear model was reformulated in an elemental form to predict volume of roll wear and then wear depth on the roll was calculated using the results of finite element analysis. Abrasive wear occurs at contact area in the roll forming process and the results of simulation are compared with experimental data in production line. The wear simulation approach with 3-D FEM program for roll forming process, SHAPE-RF is in good agreement with it in tendency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.79-87
• /
• 1999

The most part of the faculty drop a trouble and damage of machine equipment even if whatever cause they break out take place at local and trifling place and the factor dominating their trouble is due to wear debris occurred in the lubricated machine moving surface. This study has been car-ried out to identify morphology of wear debris on the lubricated machine moving system by means of computer image analysis. Namely the wear debris contained in lubricating oil extracted from movable machine equipment will be filtered through membrane filter(void diameter 0.45${\mu}m$) and will be analyzed with its data information such as 50% volume diameter aspect roundness and reflectivity. Morphological characteristic of wear debris is easily distinguished by four shape parameters it is necessary to divide small class of every 100 wear debris in total wear particles in order to distinguish morphological characteristic of wear debris more easily by computer image analysis. We are sure that operation condition diagnosis of the lubricated machine moving surfaces is possible by computer image analysis.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.250-255
• /
• 2009

Oxidation characteristics of Zirlo and Zircaloy-4 tubes, which are widely used as nuclear power fuel cladding, are studied in steam environment up to $1200^{\circ}C$. Oxidation resistances are compared in terms of the mass increase due to the absorption of oxygen. The evolution of microscopic structure accompanied with the oxidation process is investigated. Also, the influence of oxidation on the fretting wear characteristics of the tubes is studied. Piezo-electrically actuated rig is employed to fret the tubes with cross-contacting arrangement. Wear scar is observed and measured, by using microscopes and a 3D-profiler. The results of fretting wear are quantified in terms of scar size, wear volume and wear coefficient, and compared for the three different tube materials of oxidated Zirlo, virgin Zirlo and Zircaloy-4.