• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.335-338
• /
• 2004

In this paper the experiments of insulation characteristics by temperature change of $SF_6$ gas and insulation characteristics about liquid $SF_6$ in GIS(Gas Insulated Switchgear) were described. From this result, at low temperature, the breakdown voltage was increased with a drop of temperature and an increase of the inner pressure in GIS. The ability of insulation in liquid $SF_6$ was higher than that of the highly pressurized $SF_6$ gas. A liquid $SF_6$ discharge characteristics was caused by bubble formed evaporation of liquid $SF_6$ and bubble when high voltage apply to electrode. Corona was happened to weak bubble and was proceed to new bubble breakdown.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.10
• /
• pp.821-827
• /
• 2001

In this study performed to identify a degradation mechanism in macromolecular insulating material, the contact angel, surface potential decay, surface resistivity, and XPS analysis were compared after exposure of FRP laminate to plasma discharge. In the case of contact angle, the surface of specimen untreated showed weak hydrophobic property of 73。. However, the contact angle was decreased to 20。in the plasma-treated specimen. In the case of chemical changes arising form plasma treatment, carboxl radicals were generated mainly in the surface treated, which was rapidly changed to the hydrophilic one. In the corona potential decay study to determine the electrical changes of the surface, positive charges were rapidly decreased when compared with negative charges, leading to negative property in the surface of specimen not treated. However, in the case of the hydrophilic surface, lots of carboxl radicals acting as positive polarity were generated, resulting in positive surface. Owing to such positive surface, charges of negative polarity applied were rapidly decreased.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.11
• /
• pp.541-545
• /
• 2002

This paper proposes the new narrow erase method to erase wall charges formed in an AC plasma display panel (PDP) cell. In the proposed method, pulse timing of switch at the sustain period is adjusted for inducing, a weak discharge. Then, after the narrow erase, the voltage of the X electrode is set to differ from that of the Y electrode. For the proposed method, the measured maximum address voltage margin was 38.3V at Y_Rest voltage of 100V and sustain voltage of 180${\sim}$185V. However, for the conventional method, in which the X and Y electrodes are set to be of equal voltage after the narrow erase, the measured maximum address voltage margin was 31.3V at Y_Rest voltage of 150V and sustain voltage of 180V. This result shows that the measured maximum voltage margin for the proposed method is about 7V(22%) higher than that for the conventional method.

• Journal of Mechanical Science and Technology
• /
• v.19 no.2
• /
• pp.605-617
• /
• 2005

A sudden discharge of mass flow from the exit of a duct can generate an impulsive wave, generally leading to undesirable noise and vibration problems. The present study develops an understanding of unsteady flow physics with regard to the impulsive wave discharged from a duct, using a numerical method. A second order total variation diminishing scheme is employed to solve three-dimensional, unsteady, compressible Euler equations. Computations are performed for several exit conditions with and without ground and wall effects under a change in the Mach number of an initial shock wave from 1.1 to 1.5. The results obtained show that the directivity and magnitude of the impulsive wave discharged from the duct are significantly influenced by the initial shock Mach number and by the presence of the ground and walls.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.323-325
• /
• 1995

An Inductively Coupled Plasma(ICP) was employed to prepare the Diamond-Like Carbon film with $CH_4$ gas. We observed the changes of mechanical, optical properties and internal stress of the films according to the variation of discharge power and negative-self bias. When weak magnetic field is applied, the properties of film are observed to change drastically. In magnetized case, the micro-hardness and the internal stress increase up to critical point and droped down in marked contrast to unmagnetized case. It suggests that large amount of ion flux exists due to high dissociation rate of the reactive radicals in plasma with magnetic field as reported elsewhere. As a result of FT-IR absorption measurement it could be confirmed that the $CH_x$ bonding and the micro-hardness and the internal stress decreased with the increase of negative-self bias.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.177-179
• /
• 2011

The purpose of this study is to enhance an adhesion between substrate and Diamond-like Carbon (DLC) film. DLC has many outstanding properties such as low friction, high wear resistance and corrosion resistance. However, it is difficult to achieve enough adhesion because of weak bonding between DLC film and the substrate. For improvement adhesion, a layer between DLC film and the substrate was prepared by dual post plasma. DLC film was deposited on nitrided layer by linear ion source. The composed compound layer between substrate and DLC film was investigated by Glow Discharge Spectrometer (GDS) and Scanning Electron Microscope (SEM). The synthesized bonding structure of DLC film was analyzed using a micro raman spectrometer. Mechanical properties were measured by nano-indentation. In order to clarify the mechanism for improvement in adhesive strength, it was observed by scratch test.

• Textile Coloration and Finishing
• /
• v.9 no.5
• /
• pp.75-81
• /
• 1997

o-Aminobenzene sulfone-N-ethylanilide, the diazo component of C.I. Acid Red 57, is currently being diazotised by the use of nitrosylsulphuric acid because of its high molecular weight and weak basicity. However, this method has many problems such as complicated manufacturing process and discharge of large volume of strong acidic effluent. In this study, the possibility of replacing nitrosylsulphuric acid method by direct method, which is simpler and produces less effluent, has been checked and the optimum process condition was studied. The effect of HCl concentration, the amount of sodium nitrite and particle size of diazo component on diazotisation yield was investigated. The optimum pH condition for coupling reaction was also evaluated.

• Proceedings of the KIEE Conference
• /
• 1998.07e
• /
• pp.1791-1793
• /
• 1998

The thin film metal electrode for PDP needs low resistivity and strong adhesion. But the sputtered copper film is weak, in the adhesion between copper and glass. In this paper, we investigated the characteristics of resistivity and adhesion about Cu thin film using Ion Beam Assisted DC Planar Magnetron Sputtering(DCPM) Device.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.6
• /
• pp.307-314
• /
• 2021

Diamond-like carbon (DLC) is difficult to achieve sufficient adhesion because of weak bonding between DLC film and the substrate. The purpose of this study is to improve the adhesion between substrate and DLC film. DLC film was deposited on AISI H13 using linear ion source. To improve adhesion, the substrate was treated by dual post plasma nitriding. In order to define the mechanism of the improvement in adhesive strength, the gradient layer between substrate and DLC film was analyzed by Glow Discharge Spectrometer (GDS) and Scanning Electron Microscope (SEM). The microstructure of the DLC film was analyzed using a micro Raman spectrometer. Mechanical properties were measured by nano-indentation, micro vickers hardness tester and tribology tester. The characteristic of adhesion was observed by scratch test. The adhesion of the DLC film was enhanced by active screen plasma nitriding layer.

• Journal of Industrial Technology
• /
• v.43 no.1
• /
• pp.43-48
• /
• 2023

Spinel LiNi_0.5Mn_1.5O₄ (LNMO) has been considered as one of most promising cathode material, because of its low-cost and competitive energy density. However, 4.7V vs. Li/Li⁺ of high operating potential facilitates electrolyte degradation on cathode-electrolyte interface during charge-discharge process. In particular, commercial polyvinylidene fluoride (PVDF) is not sutaible for LNMO cathode binder because its weak van der waals force induces thick and non-uniform coverage on the cathode surface. In this review, we study high performance binders for LNMO cathode, which forms uniform coating layer to prevent direct contact between electrolyte and LNMO particle as well as modifying high quality cathode electrolyte interphase, improved cell performace.