• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.7
• /
• pp.37-45
• /
• 2002

In this paper, the microwave characteristics of traveling-wave electroabsorption coplanar waveguide modulator have been analyzed and optimized precisely by using the 3-dimensional finite-difference time-domain method (FDTD). Microwave characteristics are affected by the thickness of intrinsic layer, the width of meas, and the distance between signal electrode and ground electrode on traveling-wave type structure. In case that intrinsic layers are composed of InAsP/InGaP (1.3Q), the optimized distance between signal electrode and ground electrode, the optimized intrinsic region thickness and the width of waveguide are founded to be $3{\mu}m,\;039{\mu}m\;and\;2{\mu}m$, respectively, to minimize microwave loss and to obtain velocity and impedance matched structure. By using the FDTD, we could design the traveling-wave electroabsorption modulator more precisely.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1969-1971
• /
• 2002

This paper presents the design and performance of low pull-in voltage MEMS switches for commercial cellular/PCS applications. The switches have all-metal (3 ${\mu}m$ thick Au) movable plates over CPW(Coplanar Waveguide) transmission line. The stress gradient in a movable plate is considered in mechanical design to obtain an accurate pull-in voltage. Series metal-to-metal contact switches are fabricated and evaluated. Those switches exhibit the low loss(<0.2 dB @1.9 GHz) with good isolation(55 dB @1.9 GHz).

• Journal of information and communication convergence engineering
• /
• v.8 no.5
• /
• pp.489-492
• /
• 2010

This paper proposes the planar-type modified monopole antennas of loop structure. This antenna has an opened center of a conventional closed loop structure with an inside-folded terminal of the loop microstrip line. The size of the proposed antenna was minimized by folding the end of the loop. Also, the reactance value has been minimized by increasing capacitances between the coupled microstrip line. Therefore the proposed antenna has been compacted to about 20% from a conventional loop antenna and has increased its efficiency. The proposed antennas have an omni-directional pattern, the antenna gain was 3.67 [dBi] and the bandwidth was 900 MHz (2.6~3.56 GHz) with VSWR$\leq$2 from the simulated and the measured results. The frequency utilization coefficient was 29.9%. These properties could satisfy the S-DMB band.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.1
• /
• pp.1-4
• /
• 2012

In this paper, the planar type modified folded loop antennas for S-DMB band is proposed. The proposed antenna consisted of opened center of a conventional closed loop and folded terminal of microstrip line to inside loop antenna. The sizes proposed antenna was minimized by folding the terminal of the loop. Also, It was minimized reactance value by increasing capacitances between coupled microstrip line. Therefore the proposed antennas compacted about 20% than a conventional loop antenna and increased efficiency of antenna. The proposed antennas got an omni-directional pattern, the antenna gain was 3.67 [dBi] and the bandwidth was 900 MHz (2.6-3.56 GHz) with VSWR${\leq}$2 from the simulated and the measured results. The frequency utilization coefficient was 29.9 %. These properties could satisfy the S-DMB band.

• ETRI Journal
• /
• v.41 no.2
• /
• pp.262-269
• /
• 2019

This paper introduces a low-cost, high-performance mmWave antenna array module at 77 GHz. Conventional waveguide transitions have been replaced by 3D CPW-microstrip transitions which are much simpler to realize. They are compatible with low-cost substrate fabrication processes, allowing easy integration of ICs in 3D multi-chip modules. An antenna array is designed and implemented using multilayer coupled-fed patch antenna technology. The proposed $16{\times}16$ array antenna has a fractional bandwidth of 8.4% (6.5 GHz) and a 23.6-dBi realized gain at 77 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.9
• /
• pp.1098-1106
• /
• 2007

This paper presents active antenna diplexers implemented into an ultra-wideband CPW(Coplanar Waveguide) fed monopole antennas. The proposed active antenna diplexer is designed to direct interconnect the output port of a wideband antenna to the input port of two active(HEMT) devices, where the impedance matching conditions of the proposed active integrated antenna are optimized by adjusting CPW(Coplanar Waveguide) feed line to be the length of 1/20 $\lambda_0$(@5.8 GHz) in planar type wideband antenna. The measured bandwidth of the active integrated antenna shows the range from 2.0 GHz to 3.1 GHz and from 5.25 GHz to 5.9 GHz. The measured peak gains are 17.0 dB at 2.4 GHz and 15.0 dB at 5.5 GHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.2
• /
• pp.89-95
• /
• 2003

In this paper, we have designed and fabricated high conversion gain Q-band active sub-harmonic mixers for a receiver of millimeter wave wireless communication systems. The fabricated active sub-harmonic mixer uses 2nd harmonic signals of a low local oscillator (LO) frequency. The fabricated mixer was successfully integrated by using $0.1{\;}\mu\textrm{m}$GaAs pseudomorphic high electron mobility transistors (PHEMTs) and coplanar waveguide (CPW) structures. From the measurement, it shows that maximum conversion gain of 4.8 dB has obtained at a RF frequency of 40 GHz for 10 dBm LO power of 17.5 GHz. Conversion gain from the fabricated sub-harmonic mixer is one of the best reported thus far. And a phase noise of the 2nd harmonic was obtained -90.23 dBc/Hz at 100 kHz offset. The active sub-harmonic mixer also ensure a high degree of isolations, which are -35.8 dB from LO-to-IF and -40.5 dB from LO-to-RF, respectively, at a LO frequency of 17.5 GHz.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.575-578
• /
• 2005

We report on a low-cost V-band wireless transceiver with no use of any local oscillator in the receiver block using a self-heterodyne architecture. V-band Microwave monolithic IC (MMIC) modules were developed to demonstrate the wireless transceiver using coplanar waveguide (CPW) and GaAs PHEMT technologies. The MMIC modules such as the MMIC low noise amplifier (LNA), medium power amplifier (MPA) and the up/down-mixer were installed in the transceiver system. To interface the MMIC chips with the component modules for the transceiver system, CPW-to-waveguide fin-line transition modules of WR-15 type were designed and fabricated. The fabricated LNA modules showed a $S_{21}$ gain of 8.4 dB and a noise figure of 5.6 dB at 58 GHz. The MPA modules exhibited a gain of 6.9 dB and a $P_1$ $_{dB}$ of 5.4 dBm at 58 GHz. The conversion losses of the up-mixer and the down-mixer module were 14.3 dB at a LO power of 15 dBm, and 19.7 dB at a LO power of 0 dBm, respectively. From the measurement of V-band wireless transceiver, a conversion gain of 0.2 dB and a P $_{1dB}$ of 5.2 dBm were obtained in the transmitter block. The receiver block showed a conversion gain of 2.1 dB and a P $_{1dB}$ of -18.6 dBm. The wireless transceiver system demonstrated a successful data transfer within a distance of 5 meters.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.210-219
• /
• 2005

We report on a low-cost V-band wireless transceiver with no use of any local oscillator in the receiver block using a self-heterodyne architecture. V-band millimeter-wave monolithic IC (MMIC) modules were developed to demonstrate the wireless transceiver using coplanar waveguide (CPW) and GaAs PHEMT technologies. The MMIC modules such as the MMIC low noise amplifier (LNA), medium power amplifier (MPA) and the up/down-mixer were installed in the transceiver system. To interface the MMIC chips with the component modules for the transceiver system, CPW-to-waveguide fin-line transition modules of WR-15 type were designed and fabricated. The fabricated LNA modules showed a $S_{21}$ gain of 8.4 dB and a noise figure of 5.6 dB at 58 GHz. The MPA modules exhibited a gain of 6.9 dB and a $P_{1dB}$ of 5.4 dBm at 58 GHz. The conversion losses of the up-mixer and the down-mixer module were 14.3 dB at a LO power of 15 dBm, and 19.7 dB at a LO power of 0 dBm, respectively. From the measurement of V-band wireless transceiver, a conversion gain of 0.2 dB and a $P_{1dB}$ of 5.2 dBm were obtained in the transmitter block. The receiver block showed a conversion gain of 2.1 dB and a $P_{1dB}$ of -18.6 dBm. The wireless transceiver system demonstrated a successful data transfer within a distance of 5 meters.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.103-108
• /
• 2004

In this paper, we present MIMIC(Millimeter-wave Monolithic Integrated Circuit) up-mixer with low conversion loss and low LO power for the V-band transmitter applications. The up-mixer was successfully integrated by using 0.1 ㎛ GaAs pseudomorphic HEMTs(PHEMTs) and coplanar waveguide (CPW) structures. The circuit is designed to operate at RF frequencies of 60.4 GHz, IF frequencies of 2.4 GHz, and LO frequencies of 58 GHz. The fabricated MIMIC up-mixer size is 2.3 mmxl.6 mm. The measured results show that the low conversion loss of 1.25 dB when input signal is -10.25 dBm at LO power of 5.4 dBm. The LO to RF isolation is 13.2 dB at 58 GHz. The fabricated V-band up-mixer represents lower LO input power and conversion loss characteristics than previous reported millimeter-wave up-mixers.