• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.1
• /
• pp.16-26
• /
• 1998

This paper presents a design methodology for magnetically tunable X-band E-plane type waveguide filters. The proposed design is based on using of quarter wavelength transmission line for compensating the negative length transmission line of end K-inverters of E-plane type waveguide filters. The derived formulae are applied for initial design and the correction method is also provided for final design by considering the frequency dependent characteristic of K-inverters. The analysis results of E-plane pype waveguide structure loaded with ferrite slab are obtained using the edge based finite element method including higher order mode effecets. It is shown that the unilateral finline E-plane type waveguide filter as well as the bilateral finline E-plane type waveguide filter achieves the the manetically tunable characteristic. The X-band experimantal results for bilateral and unilateral finline E-plane type waveguide filters agree well with the simulated data.

• Korean Journal of Optics and Photonics
• /
• v.9 no.6
• /
• pp.408-412
• /
• 1998

As the radius of curvature of curved optical waveguide gets smaller, the loss increases at the junction of linear-curved waveguide by the cross sectional mode mismatch. The concept of lateral offset has been used widely to minimize it, and simple method of maximum matching has been efficient for most cases of silica waveguide with low optical confinement and large radius of curvature. Here, we analyzed that the propagation mode characteristics of the lateral offset and propagation mode characteristics of general case with effective index method and Airy function solution. As the normalized frequency varies, mode characteristics changes near the boundary of 1/V=0.7 and the simple matching of gaussian profile might give -35% of error at most. We proposed improved method with a new correction factor to improve the mode mismatch problem of conventional methods for general cases, and showed the convenience and feasibility of this method for the calculation of the lateral offset.

• Laser Solutions
• /
• v.8 no.1
• /
• pp.9-18
• /
• 2005

The laser direct writing method using a UV Argon-ion laser is studied for fabrication of waveguide. The laser direct writing system is constructed with a vision camera, a xy-stage, a motion controller and the delivery components of a laser beam. The UV Argon-ion laser has wavelength range of $333.6\~363.8$ nm. A photo-active UV curable polymer for a planar light-wave circuit(PLC) of single mode is used. This polymer is irradiated by Argon-ion laser and developed by a solvent after a post-baking. The optimum laser direct writing condition is obtained experimentally by changing various process parameters such as laser power, writing speed and focal length. The propagation and coupling loss of a optical waveguide was measured as 1dB/cm and 0.6dB/cm, respectively. Also, the minimum width of waveguide of $100{\mu}m$(ZPLW-207) is obtained. Finally, the waveguides of line, bend and branch type are successfully fabricated.

• Journal of electromagnetic engineering and science
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2017

This paper introduces a technique to obtain the broadband characteristics of circularly polarized antennas using an L-shaped probe. A waveguide antenna is suitable for obtaining high gain and handling convenience in some applications; however, the asymmetrical structure of the L-shaped probe results in cross-polarization and frequency dependence on the field distribution of higher-order modes (HOM). In addition to the basic characteristics of a waveguide antenna with an L-shaped probe, the author discusses some techniques to reduce the HOM and cross-polarization. As a result, the 3-dB axial ratio (AR) is obtained with the fundamental mode even when the frequency is expanded to the region for HOM of TM. This reduction is mainly due to the cutoff structure to the TM mode around the short wall of the waveguide. Furthermore, some aperture modification techniques can reduce the cross-polarization in a wide range of angles in the radiation pattern. Such techniques and their mechanisms are discussed in this paper. The obtained performance shows that the proposed antennas have a wide range of angles of 3-dB AR in the radiation pattern, broadband characteristics in impedance and AR, and low variation in group velocity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.8
• /
• pp.637-645
• /
• 1998

The characteristics of waveguide, electrode and packaging fabricated for acousto-optic tunable filters(AOTF) used for optical communications were analyzed. A $Ti:LiNbO_3$in-diffusing method was employed for the formation of the optical waveguide with a dimension of width $8{\mu}m$, length $30000-50000{\mu}m$ and varying the thickness. The diffusion was carried at $1050^{\circ}C$ for 8 hours to pattern the optical waveguide. The resulted waveguide exhibited a single mode at 1550nm optical wavelength. The width of IDT, with 10 SAM periods, was $5000{\mu}m$ . Impedances of the electrodes deposited with Au were analyzed using a network analyzer; $48.1\Omega$ at the center frequency of 193MHz for electrode thickness of $1500{\AA}$ and $50.7\Omega$ at the center frequency of 192MHz for $1600\AA$. And the characteristics of packaged AOTF was analyzed. When the electrical frequency 177.1MHz was applied to the device, the mode conversion efficiency was measured as 63% at the optical wavelength 1515nm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.1
• /
• pp.36-49
• /
• 1987

A planar waveguide model is presented for calculating dispersion characteristics of the normalized phase velocity and characteristic impedance with the frequency dependent effective dielectric constand and effective width in microstrip lines of the hybrid mode. Eeff(f) and Weff(f) are applied to a planar waveguide model by using an empirical relations and formula designed for CAD purposes as a function of frequency. A wide range of relative dielectric constants and the strip $h_{width}$strate height(W/h ratios), $0.5$\leq$W/h\leq2.5$ are used. These results are compared with static value, spectral domain analysis, and empirical results. As the result of a computer simulation, in the case of using a planar waveguide model, the frequency dependent normalized phase velocity is more closely approached to 1/ and characteristic impedance is more increased than the other method that has already been presented as the increasing of the frequency. And, the case of applying Eeff(f) designed for the purpose of CAD to this proposed model is show in better result than the case of using a empirical relations.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.561-568
• /
• 2017

In order to effectively utilize the Coarse Wavelength Division Multiplexing(CWDM) technology in optical integrated devices, a design of a wavelength selective coupler structure between an optical fiber and an optical waveguide in a flat substrate is can be considered. In this paper, we consider the coupling between a silicon waveguide with an air trench and a single mode fiber. We investigated the tendency of coupling efficiency and its limitations according to the grating depth. For this purpose, the coupling efficiency of coupler structure designed through modeling based on coupled mode theory is predicted and quantitatively compared with simulation results using finite element method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.173-181
• /
• 2011

In this paper, we propose a half mode substrate integrated waveguide(HMSIW) balanced bandpass filter to yield improved isolation between output ports. In order to achieve good isolation, resistive coupling slot is employed in HMSIW filter. The measurement results show that the insertion losses($S_{21}$, $S_{31}$) are $5.4{\pm}0.2$ dB and input return loss($S_{11}$) is more than 10 dB from 5.8 GHz to 6.4 GHz. Moreover isolation between output ports is larger than 18 dB and phase difference of output ports is $180{\pm}10^{\circ}$.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.339-341
• /
• 2010

The fundamental transverse mode lasing of a hybrid laser diode is a prerequisite for efficient coupling to a single-mode silicon waveguide, which is necessary for a wavelength-division multiplexing silicon interconnection. We investigate the lasing mode profile for a hybrid laser diode consisting of silicon slab and InP/InGaAsP deep ridge waveguides. When the thickness of the top silicon is 220 nm, the fundamental transverse mode is lasing in spite of the wide waveguide width of $3.7{\mu}m$. The threshold current is 40 mA, and the maximum output power is 5 mW under CW current operation. In the case of a thick top silicon layer (1 ${\mu}m$), the higher modes are lasing. There is no significant difference in the thermal resistance of the two devices.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.453-458
• /
• 2014

A novel high birefringent polymer terahertz (THz) fiber with a suspended elliptical core is proposed in this paper. The introduction of an elliptical core can enhance asymmetry to realize high mode birefringence, and a large porous outer cladding effectively isolates the core-guided mode from interacting with the surrounding environment. A full-vector finite element method(FEM) is used to analyze the characteristics of the THz fiber. Simulation results show that the suspended elliptical fiber exhibits high mode birefringence on a level of $10^{-2}$ over a wide frequency range, and an extremely large mode birefringence(${\approx}0.06226$) is obtained when ellipticity is 0.2. Moreover, a suspended hollow elliptical core fiber is also discussed for the purpose of lower loss, however high mode birefringence and low relative absorption loss can not coexist in such a kind of fiber.