• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1644-1654
• /
• 2018

Eigenvalue distributions for a periodic metal-insulator-metal waveguide, classified into the point spectrum and the discretized continuous spectrum (DCS), are investigated as functions of frequencies, gap widths, and periods. Muller's method is suggested for solving exact eigenvalues, and we propose the scheme for finding proper initial values in the Muller's method by considering only ${\Re}e({\varepsilon}_r)$ in the dispersion equation. We then find that anti-crossing behavior, repulsive effect between the point spectrum and the DCS, becomes stronger when the real parts of the roots in the point spectrum have smaller values. Finally, we examine the transmittances of a single subwavelength slit for real metals using the mode matching technique. The transmittances in real metals similarly follow those of the perfect electric conductor (PEC) at low frequencies, while the patterns at higher frequencies begin to differ from the PEC.

• Journal of Information Processing Systems
• /
• v.15 no.1
• /
• pp.189-202
• /
• 2019

During thermal power coal-fired boiler operation, it is very important to detect the pulverized coal concentration in the air pipeline for the boiler combustion stability and economic security. Because the current measurement methods used by power plants are often involved with large measurement errors and unable to monitor the pulverized coal concentration in real-time, a new method is needed. In this paper, a new method based on microwave circular waveguide is presented. High Frequency Electromagnetic Simulation (HFSS) software was used to construct a simulation model for measuring pulverized coal concentration in power plant pipeline. Theoretical analysis and simulation experiments were done to find the effective microwave emission frequency, installation angle, the type of antenna probe, antenna installation distance and other important parameters. Finally, field experiment in Jilin Thermal Power Plant proved that with selected parameters, the measuring device accurately reflected the changes in the concentration of pulverized coal.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.107-114
• /
• 2022

The effects of ring radius and coupling spacing on the free spectral range (FSR), full width at half maximum (FWHM), quality factor, and sensitivity of single-channel and add-drop channel slot ring resonators were systematically investigated using FIMMPROP and PICWAVE numerical software. The single-channel ring resonator exhibited better characteristics, namely, a wider FSR and narrower FWHM compared with the add-drop structure; thus, it was evaluated to be more suitable for biochemical sensors. The FSR, FWHM, quality factor, and sensitivity for a single channel ring resonator with a radius of 59.4 ㎛ and coupling gap of 0.5 ㎛ were 2.4 nm, 0.087 nm, 17677, and 550 [nm/RIU], respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.3
• /
• pp.21-27
• /
• 2023

In this article, a plate-type megasonic cleaning system with cooling pins is proposed for the sliced ingot, which is a raw material of silicon (Si) wafers. The megasonic system is operated with a lead zirconate titanate (PZT) actuator, which has high electric resistance, thus when it is being operated, it dissipates much heat. So this article proposes a megasonic system with cooling pins. In the design process, finite element analysis was performed and the results were used for the design of the waveguide. The frequency with the maximum impedance value was 998 kHz, which agreed well with the measured value of 997 kHz with 0.1 % error. Based on the results, the 1 MHz waveguide was fabricated. Acoustic pressures were measured, and analyzed. Finally, cleaning tests were performed, and 90 % particle removal efficiency (PRE) was achieved over 10 W power. These results imply that the developed 1 MHz megasonic will effectively clean sliced ingot wafer surfaces.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.9-19
• /
• 1997

By noticing that most waveguide devices were connected to power source through coaxial line, three dimentional finite element analysis using TEM mode incident was tried. When tEM mode was used, being dissimilar to TE$_{10}$ mode incident, analysis model of TEM mode incident has almost the same geometry with real products. Therefore, the degree of trust about analysis result is improved. Reflection coefficients of coaxial line, W/G adaptor, magnetron obtained by simulation was compared with experimental results.

• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.199-207
• /
• 2008

Wavelength converting devices with a ridge-type waveguide in periodically poled $MgO:LiNbO_3$ are made and characterized. The experimental results are compared with theoretical analysis on the effects of waveguide dimension and duty ratio of the periodically poled structure. To show the relationship of the conversion efficiency to those factors, a new measurement system is configured. That experimental results show that the center wavelength, normalized conversion efficiency and full width half maximum of the conversion efficiency curve are 1067.45 nm, 90.7%/$Wcm^2$ and 0.17 nm, respectively. Also, the estimated results of the duty period and full width half maximum of the conversion efficiency from theoretical calculations agreed well with experimental results with the errors of 0.016 ${\mu}m$ and 0.01 nm.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.289-290
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.248-251
• /
• 1990

A new CAD program for double E-plane bandpass filters is developed based on the variational analysis method and the passband correction method combined with the synthesis procedures. By taking the widths of three narrow waveguide equally, we can design bandpass filters with best stopband characteristics.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1986.10a
• /
• pp.20-22
• /
• 1986

This paper represents a graphical design technique of the symmetrical dielectric waveguids couplers. Once the phase constants are given by a approzimate model analysis, coupling lengths are easily calculated for each coupler. These method give some new insight of the codirectional couplers.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.02a
• /
• pp.287-288
• /
• 2007