• Journal of Information Display
• /
• 제2권4호
• /
• pp.63-67
• /
• 2001

The switching power loss due to the panel capacitance during sustain period in AC PDP driving system can be minimized by using the energy recovery circuits. We proposed a new energy recovery circuit, SER1 (Seoul national univ. Energy Recovery circuit 1st). The experimental results of its application to a 42-inch surface discharge type AC PDP showed superior performance of SER1 in energy recovery efficiency and low distortion voltage waveform. Energy recovery efficiency of SER1 was measured up to 92.3 %, and the power dissipation during the sustain period was reduced by 15.2 W in 2000 pulse/frame compared with serial LC resonance energy recovery circuit.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.96-105
• /
• 2015

In recent years, the multilevel converters have been given more attention due to their modularity, reliability, failure management and multi stepped output waveform with less total harmonic distortion. This paper presents a novel symmetric multilevel inverter topology with reduced switching components to generate a high quality stepped sinusoidal voltage waveform. The series and parallel combinations of switches in the proposed topology reduce the total number of conducting switches in each level of output voltages. In addition, a comparison between the proposed topology with another topology from the literature is presented. To verify the proposed topology, the computer based simulation model is developed using MATLAB/Simulink and experimentally with a prototype model results are then compared.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.917-921
• /
• 1991

Hydraulic fitting impulse tester is equipment which produce impulse pressure waveform that specified foreign standard of SAE, JIS etc. Test conditions of SAE J1453 about waveform standard indicates frequency of 35-70 cycle/min, pressure of 560 bar, oil temperature of 93 .+-.3.deg. C etc. and required cycle is a million over. In additions, Test condition operated continuously equipment. This development item adopted new pattern method such as intensifier and rotary distributor is different from already established fitting impulse tester applied servo valve and high pressure direct directional control valve. Therefore, this development item which compares already established item is good reliability, low cost of manufacture and save of electric energy. especially, Domestic small and medium enterprise uses this tester because of economical cause. We develope appropriateness tester which conforms to demand of user.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.181-184
• /
• 2005

Operating conditions of photovoltaic power generator is very sensitive to the PV modules. The PV module's control is an importance issue in the removing DC ripple noise. In this paper, the phase-shifted-carrier technique, which is a new three-step dc-dc power multi-converter schemes, is applied to solar generator system to improve the output current waveform. The novel type of three-step dc-dc converter presented has many features such as the good output waveform, high efficiency, low switching losses, low acoustic noise. The circuit configuration is constructed by the conventional full-bridge type converter circuit using the isolated DC power supply for which the solar cell is very suitable. In the end, a circuit design for understanding three-step dc-dc converter and new solar power system were presented

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2008년도 공동학술대회
• /
• pp.51-56
• /
• 2008

등방성 매질에서의 파형역산에 대한 연구는 1980년대부터 꾸준히 이루어져 왔으나 이방성 매질에 대한 연구는 그렇지 못하다. 본 연구에서는 이방성 매질에 대한 시간영역 셀기반 유한 차분 모델링 기법을 이용해 2차원 TI 구조에서의 파형역산 알고리듬을 개발하였다. 반복적인 비선형 역산에서 최대 급경사 방향은 역시간 구조보정의 역전파 방법을 이용하여 간접적으로 계산하였고, 이를 정규화 시키기 위해 슈도-헤시안 행렬을 이용하였다. 본 연구에서 제시된 시간영역 파형역산 기법을 이방성 매질을 포함한 2층 구조와 이방성 Marmousi 모형 자료에 적용하고 이를 등방성 매질만을 고려한 기존의 파형역산 결과와 비교하였다. 본 연구의 결과를 통해 이방성 매질을 등방성 매질로 가정하고 파형역산을 수행할 경우 정확한 영상을 얻을 수 없기 때문에, 실제 탐사 자료의 파형역산을 수행할 경우 이방성 매질을 고려해야 좀 더 정확한 지하 구조를 파악할 수 있음을 확인하였다.

• Journal of Power Electronics
• /
• 제11권3호
• /
• pp.256-263
• /
• 2011

This paper utilizes free oscillation and energy injection principles to generate and control the high frequency current in the primary track of a contactless power transfer system. Here the primary power inverter maintains natural resonance while ensuring near constant current magnitude in the primary track as required for multiple independent loads. Such energy injection controllers exhibit low switching frequency and achieve ZCS (Zero Current Switching) by detecting the high frequency current, thus the switching stress, power losses and EMI of the inverter are low. An example full bridge topology is investigated for a contactless power transfer system with multiple pickups. Theoretical analysis, simulation and experimental results show that the proposed system has a fast and smooth start-up transient response. The output track current is fully controllable with a sufficiently good waveform for contactless power transfer applications.

• 지구물리와물리탐사
• /
• 제16권4호
• /
• pp.211-216
• /
• 2013

일반적으로 평활화 필터는 주변값들과의 차이를 감소시켜 함수를 정규화하는 역할을 한다. 따라서 완전파형역산에 평활화 필터를 적용하면 역산 해를 정규화 할 수 있으며 실제 지하 구조에 가까운 영상을 얻을 수 있다. 다만 단일 평활화 계수를 사용했을 때는 지층 형태나 속도변화에 관계없이 동일하게 평활화가 이루어지므로 지층간 경계면이나 단층 등의 구조가 불명확해지는 단점이 있다. 본 논문에서는 이러한 문제를 해결하기 위해 단일 평활화 계수가 아닌 역산 반복 과정에 따라 선택적으로 평활화 계수를 조정하는 정규화 기법을 개발하였다. 먼저 파형역산에 적합한 탐사자료의 주파수 대역과 그에 대응하는 파수 범위를 분석하였다. 분석한 파수 범위에 적합한 평활화 계수를 선정하기 위해 평활화 필터의 파수 스펙트럼에서 99백분위수에 해당하는 파수를 유효최대파수로 결정하였다. 선정된 평활화 계수를 반복역산에 따라 다르게 적용하여 여러 주파수를 동시에 이용하는 멀티-스케일 완전파형역산을 구현하였다. 암염 모델과 같은 속도대비가 큰 지질구조에 대해 성공적인 역산결과를 얻음으로써 본 연구에서 개발한 평활화 계수 선택기법이 효과적인 정규화 과정을 구현한다는 것을 알 수 있었다. 또한 무작위 잡음이 더해진 인공합성 음원모음 자료에 대한 수치예제를 통해 현장 자료에 대한 적용 가능성도 확인할 수 있었다.

• 전기학회논문지P
• /
• 제62권1호
• /
• pp.1-5
• /
• 2013

The aim of this study is to research maximum harvesting energy by the optimal input wave condition. The voltage characteristics of the PZT bimorph were investigated in terms of the sine wave, triangle wave and square wave according to frequency range 0~70Hz. It was found that the square wave compared with a triangular wave or square wave was showed the higher output energy. PZT bimorph was mechanically vibrated by solenoid coil experiments, which revealed two voltage peak mode according to frequency. Maximum voltage at second vibration frequency 28Hz demonstrated that the generated DC voltage was proportional to the tip displacement of the bimorph and the phase difference between the input frequency and bimorph vibration frequency was 90 degree. It was expected that optimized design to harvest a much higher energy level from lower frequency vibrations.

• 대한한의진단학회지
• /
• 제13권1호
• /
• pp.19-35
• /
• 2009

Objectives : In the study on the waveform analysis of radial artery pulse diagnosis, we need to establish fundamentals of contemporary pulse diagnosis research. To achieve certain experimental basis on traditional pulse diagnosis, we have to research the differences of pulse waveform according to pressure (in 5 level) and position (Chon, Gwan, Cheok in radial artery). As a first step, in present thesis, we tried to find the differences of pulse waveform according to pressure. Methods and Results : In this research, we analyzed seven parameters of the waveform at five levels of pressure. The parameters are E(so called 'energy', a representative of pulse strength), h1(height of percussion wave) and h2(height of subincisura). The results were as follows. 1. When we analyzed the change of the waveform according to pressure in the left Gwan, E, hl, h2 and A differed between 1st and 2nd grade, between 1st and 3rd grade, between 1st and 4th grade, between 1st and 5th grade, between 2nd and 3rd grade, between 2nd and 5th grade, between 3rd and 5th grade and between 4th and 5th grade in 95% confidence interval. 2. And t2, t4 differed between 1st and 2nd grade, between 1st and 5th grade, between 2nd and 4th grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade and between 4th and 5th grade in 95% confidence interval. 3. W differed between 1st and 3rd grade, between 1st and 4th grade, between 2nd and 3rd grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade, and between 4th and 5th grade in 95% confidence interval. 4. And h2/h1 differed between 1st and 4th grade, between 1st and 5th grade, between 2nd and 4th grade, between 2nd and 5th grade, between 3rd and 4th grade & between 3rd and 5th grade in 95% confidence interval. 5. There were differences between 1st and 2nd grade & between 2nd and 5th grade in the case of t4/t2 in 95% confidence interval. And there were differences between 1st and 5th grade, between 3rd and 4th grade, between 3rd and 5th grade & between 4th and 5th grade in the case of W/A in 95% confidence interval. And were differences between 1st and 2nd grade, between 2nd and 3rd grade, between 2nd and 4th grade, between 3rd and 4th grade, between 3rd and 5th grade & between 4th and 5th grade in the case of A/E in 95% confidence interval. Conclusions : As mentioned above, we conclude that the waveform analysis according to five grade pressure in the left Gwan shows the difference of waveform in each grade pressure.

• 지구물리와물리탐사
• /
• 제25권4호
• /
• pp.214-216
• /
• 2022

분포형 음향 센싱(distributed acoustic sensing, DAS)은 광섬유 케이블을 수신기로 활용하는 탐사기술로서, 석유탐사 및 지진분야에서 모니터링 목적으로 활발히 적용되고 있다. 최근에는 지하매질의 물성정보를 도출하기 위해 분포형 음향 센싱 자료를 활용한 전파형역산 연구가 수행되고 있다. 분포형 음향 센싱은 광섬유 케이블 상의 두 점 간의 위상 차이에 의한 변형률을 측정하기 때문에, 기존 전파형역산 알고리즘에 직접 활용하기 어렵다. 분포형 음향 센싱 자료를 전파형역산에 활용하기 위해, 본 연구에서는 평면파 가정에서의 변형률과 수평입자속도의 관계식을 이용한 평면파 전파형역산 알고리즘을 개발하였다. 수치실험을 통해 평면파 가정에서의 변형률과 입자속도 간의 관계식이 성립함을 확인하였다. 다양한 탐사환경에서 분포형 음향 센싱 자료에 대한 전파형역산의 적용 가능성을 확인하기 위해, 육상 및 해저면 탄성파 탐사 환경을 모사한 4층 및 수정된 Marmousi-2 속도모델을 이용하였다. 제안된 전파형역산을 통해 육상 및 해저면 탄성파 탐사 환경하에서 P파 및 S파 속도구조를 정확히 도출할 수 있었다.