• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.228-236
• /
• 2021

In order to understand the underwater noise source factor of the linear pump type forced ejection system, a reduced-model compressed water experiment device was developed. The reduced-model compressed water experiment device consists of a reverberation tank, a linear pump type forced ejection device, and an underwater vehicle. The underwater noise source was selected from the hydraulic ram moving speed, the hydraulic ram/piston pipe spacing, the ejection pipe inlet/water ram area ratio, and the number of water ram inlets. The underwater vehicle was ejected into the reverberation tank by the device. The source level was derived from the measured sound pressure. The source level tends to increase as the hydraulic ram/piston tube spacing and the hydraulic ram moving speed increase. The source level tended to increase as the area ratio was increased, but the level was weak. The number of water ram inlet did not affect the source level.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.6
• /
• pp.799-810
• /
• 2009

With time, the stable management of turbidity is becoming more important in the water treatment process. So optimization of coagulation is important for the improvement of the sedimentation efficiency. we evaluated the mixing and hydrodynamic behavior in the coagulation basin using Computational Fluid Dynamics (CFD). The items for evaluation are a location and the speed of agitator and angle of an injection pipe. The results of the CFD simulation, the efficacy of mixing in the coagulation basin was not affected according to one or two injection pipe and angle of an injection pipe. If there is a agitator near outlet of coagulation basin, the efficacy of mixing don't improve even though the speed of agitator increase. So location of agitator is perfect when it locate center at the inlet stream. The coagulation basin at this study, the proper speed of agitator is form 20rpm to 30rpm.

• Water for future
• /
• v.20 no.2
• /
• pp.127-138
• /
• 1987

For determination of the design wave, a method of estimating the design wind speed at sea from the wind records at the nearby weather stations on land is proposed. Along the West Coast, the design wind speed are shown to have two main directions; namely, N through W, and WSW through S. Through the analysis of weather maps, fetches for the main wind directions along the West Coast are determined. The wind speeds at sea are found to have 0.8~0.9 times the wind speed at the stations on land for U$\geq$20m/s. The West Coast may be divided into three regions for which fetches are determind uniquely. Design waves with return period of 100 years are determined by the revised S.M..B. method along the West Coast, and show the deep water significant wave heights of 4.4~8.3 meters with wave periods of 8.9~12.0 seconds.

• Journal of Biosystems Engineering
• /
• v.23 no.3
• /
• pp.245-252
• /
• 1998

The structural characteristics of a small scale rice polisher was analyzed to improve its performance. Spraying characteristic of nozzles used for rice polishing was also analyzed by a machine vision system. The internal pressure of the polishing chamber was measured according to outlet resistance, water spraying, and roller shaft speed. In addition, the performance of the rice polisher was evaluated to improve it in the basis of internal pressure in polishing chamber, whiteness, and broken rice ratio of clean rice according to the operating conditions. Actual nozzle discharge rate and drop size were 125 cc/min and 86~97 ${\mu}{\textrm}{m}$, respectively. In the case of water spraying on rices, the internal pressure showed 4.9~9.8N/$\textrm{cm}^2$ increase. broken rice ratio decreased, and there was no difference in whiteness. The internal pressure inueased up to two times with the increase of the outlet resistance. Also, the pressure at the upper part of screen was one and half times as high as the pressure at the lower part. In the case of water spraying rate of 150 cc/min, the roller shaft speed of 850 rpm resulted in no difference in whiteness and decrease of 0.3% in broken rice ratio, comparing to the roller shaft speed of 950 rpm.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1998.06b
• /
• pp.206-216
• /
• 1998

The structural characteristics of small scale rice polisher was analyzed to improve its performance. Spraying characteristic of nozzles used for rice polishing was also analyzed by a machine vision system. The internal pressure of the polishing chamber was measured according to outlet resistance, water spraying , and roller shaft speed. In addition , the performance of the rice polisher was evaluated to improve it in the basis of internal pressure in polishing chamber, whiteness , and broken rice ratio of clean rice according to the operating conditions. Actual nozzle discharge rate and drop size were 125cc/min and 86.97㎛, respectively. In the case of water spraying on rices, the internal pressure showed 4.9-9.8N/㎠ increase, broken rice ration decreased , and there was no difference in whiteness . The internal pressure increased up to two time with the increase of the outlet resistance. Also, the pressure at the upper part of screen was one and half times as high as the pressure at the lower part. In the case of water spraying rate of 150 cc/min, the roller shaft speed of 850 rpm resulted in no difference in whiteness and decrease of 0.3%in broken rice ratio, comparing to the roller shaft speed of 950 rpm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.7 s.178
• /
• pp.1841-1846
• /
• 2000

To examine the effect of acid fog on the corrosion fatigue behavior in structural steel, fatigue tests under acid fog atmosphere were carried out in comparison with distilled water. The corrosive c omponents contained in acid fog pile up the corrosion products on crack face and show a crack branching and crack tip blunting. Therefore, due to these workings crack growth rate was reduced by decreasing the effective stress range in crack tip rather than under distilled water. Also the effect of sulfuric acid, which is the main component of acid fog, and testing speed on fatigue crack growth were examined. It was found that corrosion behavior was remarkably dependent upon pH and Hz rather than components of acid fog. According as pH and testing speed decrease below a specific value, crack growth was accelerated in comparison with distilled water. This reveals that due to liquid having strong acidity and slow speed of test the crack face dissolution was promoted, so crack closure was disturbed in the process of stress descent.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.1
• /
• pp.34-41
• /
• 2014

When a ship sails in shallow water, it is well known that an additional sinkage and trim of the ship(squat) is caused by change of hydrodynamic force between the seabed and the bottom of a ship. In this paper, to examine this phenomenon by model tests, the squat of KCS model ship at a low speed is measured by the vision based ship motion measurement system during HPMM tests. Various combinations of a ship speed, a rudder angle and a drift angle were tested at three depth conditions(H/T = 1.2, 1.5 & 2.0). As a result, increase of the ship's speed and ship's drift angle caused an increase in ship squat, but the ship's rudder angle did not. The rate of increase in ship squat was the most at H/T = 1.2 condition. Lastly these experimental results are compared to the results by three empirical formulas and two CFD methods. The tendency of ship squat measured by experiment is similar to those of empirical formulas.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.16 no.2
• /
• pp.9-14
• /
• 1979

Havelock was considered the wave resistance of a post extending vertically downwards through the water from the surface, its section by a horizontal plane being the same at all depths and having its breath small compared with its length. This enables us to elucidate certain points of interest in ship resistance. However, the ship has not infinte draft. So, the problem which is investigated in detail in this paper is the wave resistance of a mathematical quadratic model in a uniform stream. The author wishes to study the effect of viriation of draft. The form of the water-plane is varied while keeping in length and the cross sectional area constant. As a numerical example, we calculated the wave resistance for mathematical quadratic ship models. The results are compared with a post having infinite depth. The results are as follows; The models with finer ends have smaller wave resistance up to $V/\sqrt{L}=1.1{\sim}1.2$ than its mate with blunter ends, but above this speed the models with blunter ends have less wave resistance. According to the decrease of draft, the wave resistance gap between the models with blunter ends the models with finer ends decrease at high speed. In this case of T/L=0.025, the models with finer ends have less wave resistance than the models with blunter ends at high speed.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2019

In this study, the effect of operating conditions of fan-coil unit with an oval tube type heat exchanger on its non-dimensional performance coefficient has been investigated. Pressure drops and heat transfer rates were measured under heating condition for various water flow rates, inlet temperatures and wind speeds. As a non-dimensional performance coefficient, Colburn j-factor was evaluated. The results show that the most sensitive parameter on heat flux is the inlet temperature, which affects the heat flux 4.7 and 7.2 times more than the wind speed and water flow rate, respectively. On the other hand, the Colburn j-factor as a non-dimensionalized index decreases with the wind speed, and has an maximum when the wind speed is about 1 m/s. the Colburn j-factor increases slowly with the water flow rate and inlet temperature but at a certain range of inlet temperature, the opposite phenomenon is found.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.278-291
• /
• 2021

This paper applies load variation method to predict speed-power-rpm relationship along with propulsive performances in regular head waves, and to derive overload factors (ITTC, 2018). 'Calm-water tests' and 'resistance test in waves' are used. The modified overload factors are proposed taking non-linearity into consideration, and applied to the direct powering, and resistance and thrust identity method. These indirect methods are evaluated through comparing the speed-power-rpm relationships with those obtained from the resistance and self-propulsion tests in calm water and in waves. The objective ship is KVLCC2. The load variation method predicts well the speed-power-rpm relationship and propulsion performances in waves. The direct powering method with modified overload factors also predicts well. The resistance and thrust identity method with modified overload factor predicts with a little difference. The direct powering method with overload factors predicts with a relatively larger difference.