• Journal of Conservation Science
• /
• v.31 no.1
• /
• pp.13-20
• /
• 2015

Surface of the wooden cultural heritage has been protected from moisture by natural oils (such as perilla oil and tung oil), which accelerated degradation. But we can find seldom the research on the processes and performances of oil coatings. In this study, the water resistant performances by wood direction were compared to 3 types of natural oil and 2 types of oil stain, and the effect of additional indoor conditioning and temperature of oil were appraised in longitudinal direction. The natural oils block moisture about 79.2% comparing to the control in longitudinal direction. Especially the tung oil showed the outstanding water resistance about 90.5%. The water resistant performances decreased about 8.8% by additional indoor conditioning for 2 years. Heated oil improved the water resistance about average 5.0%.(Max. 9.6% with linseed oil).

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.5
• /
• pp.453-460
• /
• 2018

The impact of sodium hydroxide, which is one of chemicals of clean in place (CIP) for removing membrane fouling, on the PVDF membrane is reviewed with respect to physical/chemical structural change, the permeability affected therefrom. Based on the cleaning concentration applied in membrane water treatment facilities, 10% of accumulated defluorination was confirmed up to 166g.hr/L which reflects the exposure time. However, membrane resistance was confirmed to be reduced by about 10%. Through FT-IR and EDS analysis, reduction of F and change of are confirmed as factors that affect the permeability of membrane. Membrane resistance, which affects permeability, is affected by loss of additives for hydrophilicity, rather than defluorination of PVDF material. Therefore, in order to check membrane degradation degree, an accelerated test by NaOH was carried out, loss of additives was confirmed, and then PVDF inherent characteristic was observed.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.2
• /
• pp.137-144
• /
• 1997

The effcct of specific g~avity cont~olled In the .range fiom O.4 to 0.7 by particle size and added amount of A1 powder in the presence or absence of water repellent agent on the physical properties of ALC was examined to evaluate frost resistance and durability. The compressive sttcngth and the tensile strength are increased and independency with water repellent agent when the specific gravity is increased in the range from 0.4 to 0.7. According as the added amount of water repellent agent was increased. frost resistance was improved and absorption ratio was decreased. ALC produced from fine Al powder has a low volume reduction by scaling and a sound apperance after freezing/thawing test and top surface freezing test.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.256-265
• /
• 2021

Titanium is applied in various industries due to its valuable properties and abundant reserves. Generally, if a highly uniform oxide structure and a high-density oxide film is formed on the surface through anodization treatment, the utility value such as color appearance and corrosion inhibition efficiency is further increased. The objective of this study was to determine improvement of water-repellent property by controlling titanium oxide parameters such as pore size and inter-pore distance to improve corrosion resistance. Oxide film structures of different shapes were prepared by controlling the anodization processing time and voltage. These oxide structures were then analyzed using a Field Emission Scanning Electron Microscope (FE-SEM). Afterwards, a Self-Assembled Monolayer (SAM) coating was performed for the oxide structure. The contact angle was measured to determine the relationship between the shape of the oxide film and the water-repellency. The smaller the solid fraction of the surface, the higher the water-repellent effect. The surface with excellent hydrophobic properties showed improved corrosion resistance. Such water-repellent surface has various applications. It is not only useful for corrosion prevention, but also useful for self-cleaning. In addition, a hydrophobic titanium may open up a new world of biomaterials to remove bacteria from the surface.

• Advances in environmental research
• /
• v.12 no.1
• /
• pp.1-15
• /
• 2023

Wastewater of anthropogenic origin is known to harbor various bacteria that are known to be of potential risk to human health and environment. It is of utmost importance to monitor such water sources. Coliforms present in the sewage water samples of municipal sewage treatment plants located at three different places in the South Gujarat region (Surat, Navsari and Vapi) of India were analyzed for their coliforms load as well as tested for their drug resistance. Using cultivation-based techniques microbial load and drug resistance (Amoxicillin, Tetracycline, Ciprofloxacin, Erythromycin, Trimethoprim and Sulphamethoxazole) were analyzed. Water treatment statistically significantly decreased the bacterial load in Vapi and Navsari samples. The optical density of with and without antibiotics of all the three locations was shown to increase significantly after 72 hours. Of all the isolates tested, except isolate 'VA5' (resisted up to 90 ㎍ of Ampicillin) all other isolates resisted 256 ㎍ concentration of antibiotics tested. This study indicates that the sewage water is being contaminated with drugs and/or antibiotics due to industrial and/or anthropogenic activities. Regular monitoring of the water quality is required followed by implementation of environmental laws for reducing the pollutants, that are of human health and environment concern.

• Journal of Korean Society of Forest Science
• /
• v.89 no.2
• /
• pp.198-207
• /
• 2000

The diurnal and seasonal changes of water potential and stomatal diffusive resistance were investigated with the effects of shade treatment to elucidate the water relations of the one year old seedlings of Betula platyphylla var. japonica, Zelkova serrata, Acer mono, and Prunus sargentii subjected to five levels of artificial shade treatments from full sun to nearly full shading of 2-6% relative light transmittance. Stomatal diffusive resistance measured in the four deciduous hardwood species studied changed variously by growing season and by species with the five shade treatments in the ranges of 1.7~25.1s/cm in 9 a.m., 2.3~33.3s/cm in 1 p.m., and 1.1~36.8s/cm in 5 p.m.. The measurements of stomatal diffusive resistance increased with increasing the shading, and were higher in September than in June or July in most of the species studied. The stomatal diffusive resistance measured in Zelkova serrata, Acer mono, and Prunus sargentii seemed to be approximately 3~4 times higher in nearly full shading treatment than in full sun. Water potential also changed variously by growing season and by species with five different shade treatments in the ranges of -0.17~-1.20MPa in 9 a. m., -0.30~-2.03MPa in 1 p. m., and -0.18~-1.34MPa in 5 p.m., respectively. On the reverse of stomatal diffusive resistance, the measurements of water potential were lower in September than in June or July in most of the species studied, and the seasonal differences were especially greater in Zelkova serrata comparing with the other species. The water potential seemed to be higher of approximately 2~3 times in nearly full shading treatment than in full sun in all of the species studied, but the differences among the shading treatments were less in water potential than in stomatal diffusive resistance. The differences of water potential following the gradient of five shading treatment seemed to be less in Betula platyphylla var. japonica than in the other species. In Acer mono and Prunus sargentii being some shade tolerant species, the water potential increased rapidly through about noontime with raising the shading level from full sun to the intermediate shading level of 22-28% relative light transmittance, but slowly with closing to full shading. In Betula platyphylla var. japonica and Zelkova serrata being shade intolerant species, the water potential increased gradually throughout the shading levels and the increment ranges were greater in Zelkova serrata than in Betula platyphylla var. japonica.

• Journal of Korean Society for Quality Management
• /
• v.16 no.1
• /
• pp.43-48
• /
• 1988

Most of silicone used for water repellent finish is MHP (methyl hydrodiene polysiloxane), which is formed by hydrolysis and condensation polymerization of MHD (methyl hydrodiene dichlorosilane: Me H Si $Cl_2$). The cross-linking theory explains the water repellent mechanism of MHP. The silicone finish on fiber could improve in handle, softness, abrasion resistance, soil repellency, tear strength and crease resistance, as well as water repellency. According to using method silicone-water repellent finishing agents, could be devided into air dry type and curing type. MHP is the typical curing type of water repellent finishing agent, and this type requires the curing temperature above $150^{\circ}C$ at least. High curing temperature is the very drawback of this curing type. For this reason, there has been global interest in the lowering of its temperature. The objective of this study is to investigate merits of alkali treatment for silicone finishing by ANOVA and LSD (least significant difference).

• Journal of the Korean Society of Visualization
• /
• v.22 no.1
• /
• pp.61-67
• /
• 2024

In this study, the behavior of water droplets on a solid-infused surface was evaluated by quantifying a water droplet's contact angle, sliding angle, and terminal velocity. The contact angle hysteresis and sliding angle of water on the solid-infused surface were measured to be lower than those of the hydrophobic PTFE surface. It led to the enhancement of the initiation of the water droplet's movement. When the capillary number was lower than Ca < 0.004, the terminal velocity of the water droplet on the solid-infused surface was higher than the PTFE surface due to the low contact line resistance. However, the transition of the droplet morphology from a hemispherical shape to a streamlined teardrop shape beyond Ca > 0.004 lost the effect of reducing frictional resistance on the solid-infused surface.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.641-646
• /
• 1998

The structures exposed to marine environment do not show long-term durability due to corrosion of steel and deterioration of concrete by the attack of various salts dissolved in sea water. In this study, Partial substitution of cement with fly ash(20%) or blast furnace slag(40%) was made together with the addition of 4 different corrosion-inhibitors, as a protective measure of concrete structures against chemical attack of salts. Combined effects of mineral and corrosion-inhibiting admixtures were tested by measuring the resistance and compressive strength of concretes under the simulated tidal condition, which consists of alternating 12 hour periods of immersion in artificial sea water and drying in air. Both the strength and concrete resistance were found to decrease in following order, regardless of the corrosion inhibitors the concretes with blast furnace slag, those with fly ash and those without any mineral admixtures. The interrelation between compressive strength of concrete and resistance was investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.25-30
• /
• 2010

The authors have studied on the corrosion resistance of the hot stamped steel sheets for the application to automotive parts. Recently automotive companies have focused on the hot stamped parts to meet the light weighting needs and the safe reason. Because of the cost reduction of the hot stamped parts, automotive companies increase the usage of the coated steel sheets, especially Al-Si coated steel sheets. The coated layer of Al-Si coated steel sheets contains up to 50% of Fe, which was diffused from the steel sheet, after hot stamping. The hot stamped steel sheet was not phosphated due to the oxidation layer of the coating, however, the result of the water resistance test is similar to that of the conventional GA steel sheets. The pitting depth and the weight reduction of the coated layer of hot stamped steel sheets are less than those of GA steel.