• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1267-1276
• /
• 1998

Falling-film evaporation experiments with aqueous lithium bromide (LiBr) solution were performed to investigate the heat transfer characteristics of enhanced copper tubes. Enhanced tubes (a knurled tube, a spirally grooved tube, and a tube coated with $20{\mu}m$ aluminum particles) and a bare tube were selected as test specimens. Averaged evaporation fluxes of water were obtained from horizontal tubes with various film Reynolds numbers, system pressures, LiBr concentrations and degrees of wall superheat. The enhanced performance of steam generation was compared between tubes with varying parameters. The knurled tube geometry showed the most excellent performance among the tubes tested. The specified enhanced tubes were more useful for generating steam on a low grade heat source such as waste heat.

• Nuclear Engineering and Technology
• /
• v.32 no.6
• /
• pp.595-604
• /
• 2000

Flow-Accelerated Corrosion Behavior of SA106 Gr.C steel in room temperature alkaline solution simulating the CANDU primary water condition was studied using Rotating Cylinder Electrode. Systems of RCE were set up and electrochemical parameters were applied at various rotating speeds. Corrosion current density decreased up to pH 10.4 then it increased rapidly at higher pH. This is due to the increasing tendency of cathodic and anodic exchange half-cell current. Corrosion potential shifted slightly upward with rotating velocity. Passive film was formed from pH 9.8 by the mechanism of step oxidation and the subsequent precipitation of ferrous species into hydroxyl compound. Above pH 10.4, the film formation process was active and the film became stable. Corrosion current density showed increment in pH 6.98 with the rotating velocity, while it soon saturated from 1000 rpm above pH 9.8. This seems that activation process which represents formation of passive film on the bare metal surface controls the entire corrosion process

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.504-505
• /
• 2005

In this report, we demonstrate a high performance polymer thin-film transistor fabricated on a paper substrate. As a water barrier layer, parylene was coated on the paper substrate by using vacuum deposition process. Using poly (3-hexylthiophene) as an active layer, a polymer thin-film transistor with field-effect of up to 0.086 $cm^2/V{\cdot}s$ and on/off ratio of $10^4$ was achieved. The fabrication of polymer thin-film transistor built on a cheap paper substrate is expected to open a channel for future applications in flexible and disposable electronics with extremely low-cost.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.8
• /
• pp.715-719
• /
• 1996

Thin films of polyaniline (PANI) salts were in situ deposited on a Pt plate during either chemical polymerization or electrochemical polymerization. The oxidation states of the salt films were controlled by the applied DC potential. AC impedance of the Pt/PANI electrode were measured in monomer-free 1 N HCl solution in order to investigate the electrodic properties of the films at the following applied DC potentials: 0, 0.45 and 0.75 V vs. SCE. Very small differences in film conductivity according to its oxidation state were observed by analysis of the impedance spectra, the reasons of which are complicated by enriched water content in the film and possible decrease in the film thickness during the measurements. The electrochemical activity of the film/solution interface varied with its oxidation state. Stability of the film in 1 N HCl solution was also evaluated by impedance and cyclic voltammetry measurements.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.49-54
• /
• 1989

Thin solid film systems polarizing beam splitter and disk amplifier used in the high power laser system ({{{{ lambda }}0=1060nm) are designed by computer aided optimization technique. Extinction ratio of designed polarizing beam splitter for incidence angle 30$^{\circ}$, 45$^{\circ}$, 55.60$^{\circ}$ are 1:93, 1:895, 1:1991. respectively. Maximum reflectance of designed thin film system of disk amplifier is less than 3% for pumping band (500-900nm) and 0.15% for laser beam. Further, SiO film chosen as one of the suitable thin films in the high power laser system is prepared by the sol=-gel process which gives high damage threshold. When the withdrawal speed is 6.15cm/min -16.62 cm/min and the mixing ratio is in the range of 1 mol (ethylsilicate): 4-8mol(ethylalcohol) : 2mol(water), the thickness of deposited film is in the range of 500{{{{ ANGSTROM }}-1500{{{{ ANGSTROM }}.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.357-360
• /
• 2019

We demonstrate an alignment technology using an imprinting process on an inorganic NiOx film. The aligned nanopattern was fabricated on a silicon wafer by laser interference lithography. The aligned nano pattern was then imprinted onto the sol-gel driven NiOx film using an imprinting process at an annealing temperature of $150^{\circ}C$. After the imprinting process, parallel grooves had been formed on the NiOx film. Atomic force microscopy and water contact angle measurements were performed to confirm the parallel groove on the NiOx film. The grooves caused liquid crystal alignment through geometric restriction, similar to grooves formed by the rubbing process on polyimide. The liquid crystal cell exhibited a pretilt angle of $0.2^{\circ}$, which demonstrated homogeneous alignment.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.113-114
• /
• 2002

Radial, tilting 12-pad proceeding bearings are applied as the radial bearings of vertical rotors of water turbines. The mean loads are stable at the peripheral speeds of proceeding reaching 50 m/s. The operation of tilting 12-pads proceeding bearing has been introduced at the assumption of adiabatic oil film. The oil film pressure, temperature and viscosity distributions have been obtained by iterative solution of the Reynolds', energy and viscosity equations. The resulting oil film force, minimum oil film thickness, power loss, oil flow, maximum oil film pressure, maximum temperature have been computed for different load angle of bearing.

• Textile Coloration and Finishing
• /
• v.35 no.4
• /
• pp.196-205
• /
• 2023

Water-dispersed pigment is on-going study for without air pollution in the textile and print industry. Primer treatment is essential for the substrate to improve the printing quality of eco-friendly water-dispersed pigment ink. Otherwise in the case of untreated primer, the water-dispersed pigment ink will dry onto the surface and cause defective images. This study was conducted on film substrate coating (primer) to fix eco-friendly water-dispersed pigment ink on film substrate. The drying, bleeding, and color strength of the pigment ink were examined depending on the composition and mixing ratio of the coating solution. The mixing ratio of silica gel in the coating film is increased to 0, 0.5, 1, 2 and 3 and results that DK-1-3 of silica gel ratio of 1 showed the lowest bleeding such as 52%, the letter thickness of 0.76mm and DK-1-5 of SG ratio of 3 showed the highest bleeding such as 304%, the letter thickness of 2.02mm. The mixing ratio of SPA in the coating film is increased to 2.5, 5, 7.5, SPA ratio of 7.5 has a bleeding ratio of 9% and letter thickness of 0.544mm. It showed the closest value to 0.5mm. According to the result, the optimal mixing ratio of binder, polymer coagulant, silica gel is 100:7.5:1.

• Korean Journal of Food Science and Technology
• /
• v.31 no.5
• /
• pp.1289-1294
• /
• 1999

To identify the effect of packaging film on browning reaction of dried squid, 3 kinds of packaging film$(NYLON\;12\;{\mu}m/LDPE\;80\;{\mu}m)$ including transparency, white, black film were tested about browning degree of dried squid during storage at ambient temperature for 50 days. During storage period, water content and water activity were maintained almost constant, and microbial count was not changed. When color index was measured by color difference meter, L value and ${\Delta}E$ value were the highest in the dried squid packaged with transparency film. ${\Delta}E$ value was rapidly increased in early packaging period(within 10 day). TBA value was showed same tendency with ${\Delta}E$ value in early storage period. So, the browning was supposed to originated from lipid oxidation by UV light transmitted through packaging film in the early storage period.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.3
• /
• pp.494-499
• /
• 2001

To determine optimal conditions for preparing protein isolate film from fish meal, the water vapor permeability (WVP), tensile properties and solubility of fish meal proteinisolate (FMPI) film were measured. FMPI was extracted from fish meal under conditions of various extraction times at $60^{\circ}C$. Extracting time little affected to WVP of FMPI film. The film added with glycerol as plasticizer showed higher WVP than sorbitol added. As extraction time increased up to 1 hr, tensile strength and elongation were increased. While in more extracting time than 1 hr, increasing extracting time made tensile strength and elongation showed negative correlations. The correlation of soluble protein amount and tensile strength showed higher value ($r^{2}=0.83$) than that of elongation ($r^{2}=0.62$).