• Journal of Korea Foundry Society
• /
• v.2 no.4
• /
• pp.2-8
• /
• 1982

The behavior of sand and mold at high temperatures was generally agreed to importantly affect the quality of castings made. By changing water content through 2,4,6 and 8%, and bentonite content through 5,7,9 and 11%, specimens have been made according to the respective composition. Specimens have been subjected to hot compressive strength and thermal expansion at 400, 600, 800 and $1000^{\circ}C$ respectively. The results obtained were as follows ; 1. At each temperature, thermal expansion decreased and hot compressive strength increased with the increase in water content. 2. After thermal expansion was peaked at approximately $1000^{\circ}C$ the contraction and maximum hot compressive strength appeared. 3. At each temperature, maximum hot compressive strength appeared 2%, 4,6% and 8% water content for 7%, 9% and 11% bentonite content respectively. 4. When 2% $H_2O$ was added, though bentonite content was increased, hot compressive strength did not rarely change. 5. Until the thermal expansion was completed the required time was 15-18 minutes at $400^{\circ}C$ and $600^{\circ}C$, and 10-13 minutes at $800^{\circ}C$. At $1000^{\circ}C$, the required time was 7-9 minutes in order to gain the maximum expansion, after that, contraction proceeded during 3-4 minutes before expansion was completed.

• Journal of Korean Society of Water and Wastewater
• /
• v.10 no.2
• /
• pp.55-69
• /
• 1996

Backwashing is one of the most important processes in water treatment. Several models have been utilized to predict minimum fluidization velocity and expansion of media. However, it is not unusual that the actual bahavior of media dose not agree well with the prediction. This study has investigated the applicability of models in predicting the minimum fluidization velocity of sand media. However even the better model has predicted minimum fluidization velocity 1.1 to 1.8 times higher than actual fluidization velocity. The expansion rate of sand media was inspected. It is found that the actual expansion rate was greater than the predicted. In this study condition, use of $d_{10}$ instead of $d_{60}$ was better to predict the expansion of media. On the contrary to the sand media, the actual expansion of anthracite media was less than that predicted. Sometimes it is reported that the dual media has been overflown during backwashing and mixed severely at the interface. It is because the grain size distribution of anthracite has not been selected properly. The numerical values for media expansion found in this study could be referred as the useful data in operating and/or designing filter media.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.5 s.72
• /
• pp.9-14
• /
• 2006

This paper presents an analytical method, application of expansion, mechanical design, and integrated expansion design of subsea insulated pipe-in-pipe (PIP) systems. PIP system consists of a flowline and a casing pipe for the transport of high temperature and high pressure product from the subsea wells. To prevent heat lass from the fiowline, insulation material is applied between the pipes. The fiawline pipe and the casing pipe have mechanical connections through steel ring plate (water stops) and bulkheads. Pipeline expansion is defined by temperature, internal pressure, soil resistance, and interaction force between the flowline and the casing pipe. The results of the expansion analysis, the mechanical design of connection system of the two pipes and tie-in spool design are integrated for the whole PIP system.

• Food Engineering Progress
• /
• v.15 no.2
• /
• pp.148-154
• /
• 2011

The objective of this study was to determine the effect of die geometry on expansion index of extruded corn flour. Water solubility index, water absorption index and specific mechanical energy (SME) input were analyzed to observe the relationship with die geometry. The feed moisture content was 20 and 25%. Die dimensions were tapered angle (57, 95o) and length/diameter (L/D) ratio of die land (0.67, 1.67 and 2.67). The SME input was the highest at 20% moisture content and 2.23E-10 m3 die constant. The sectional and volumetric expansion indices at 20% moisture were increased with increase in die constant. However, die constant did not influence sectional expansion index of corn flour extrudate at 25% moisture content. The extruded corn flour at 25% moisture content had higher longitudinal expansion index than those of extruded corn flour at 20% moisture content. Sectional expansion and longitudinal expansion index were negatively correlated. The water absorption index and water solubility index were not affected with the die constant.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 1995.12a
• /
• pp.9-21
• /
• 1995

A planning support system enhances our ability to use water capacity expansion as an urban growth management strategy. This paper reports the development of capacity expansion modeling of water supply as part of the continuing development of such a planning support system (PEGASUS: Planning Environment for Generation and Analysis of Spatial Urban Systems) to incorporate water supply, This system is designed from the understanding that land use and development drive the demand for infrastructure and infrastructure can have a significant influence on the ways in which land is developed and used. Capacity expansion Problems of water supply can be solved in two ways: 1) optimal control theory, and 2) mixed integer nonlinear programming (MINLP). Each method has its strengths and weaknesses. In this study the MINLP approach is used because of its strength of determining expansion sizing and timing simultaneously. A dynamic network optimization model and a water-distribution network analysis model can address the dynamic interdependence between water planning and land use planning. While the water-distribution network analysis model evaluates the performance of generated networks over time, the dynamic optimization model chooses alternatives to meet expanding water needs. In addition, the user and capacity expansion modeling-to-generate-alternatives (MGA) can generate alternatives. A cost benefit analysis module using a normalization technique helps in choosing the most economical among those alternatives. GIS provide a tool for estimating the volume of demanded water and showing results of the capacity expansion model.

• Water Engineering Research
• /
• v.1 no.1
• /
• pp.75-81
• /
• 2000

The bragg reflection of obliquely incident monochromatic water waves propagating over a sinusoidally varying topography is theoretically investigated in this study. The eigenfunction expansion method is first employed to calculate reflection coefficients of water waves due to depth changes. A reasonable agreement is observed. Obtained reflection coefficients of normally incident waves are compared with laboratory measurements. Reflection coefficients of obliquely incident waves are then calculated. The wavenumber providing the Bragg reflection agrees well with analytical predictions.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.143-147
• /
• 2012

Since the expansion of perlite occurs in a few second in high temperature, it is difficult to identify an expansion phenomenon through experiments. In order to explain this phenomenon, a numerical study has been carried out by setting a model that water vapour diffuses to a tiny bubble existing in perlite melts and then makes the bubble grow and perlite expand. When the bubble grew and the perlite expanded due to the diffusion of water vapour, the dynamic temperature of perlite decreased. Meanwhile, the dynamic pressure of bubble increased at the beginning as water vapour diffuses in melts, but rather decreased after a rapid expansion of bubble.

• Journal of the korean society of oceanography
• /
• v.38 no.3
• /
• pp.87-100
• /
• 2003

The monthly observations of hydrography in the Cheju Strait from September 1995 to June 1998 show that the Cheju Strait is occupied mostly by Tsushima Current Water in winter and coastal waters in summer. In summer, the Yangtze Coastal Water appears in the upper layer and cold water in the lower layer. Especially, the Yellow Sea Bottom Cold Water appears in August 1997, and the clockwise flow of warm water along the northwestern coasts of Cheju Island is disturbed by an eastward expansion of the cold water from the northwest. The cold water expansion seems to be partly associated with strong southeasterly winds. Current measurements in the Cheju Strait suggest that there exists steady eastward barotropic component of about 5 cm/sec, which corresponds to 0.2 Sv barotropic transport in the Cheju Strait. Geostropic transport (baroclinic component) ranges from 0.1 Sv in winter to 0.4 Sv in summer. By adding the barotrophic component of 0.2 Sv, the total transport varies from 0.3 Sv to 0.6 Sv, which is consistent with previous estimations. The transport increase in summer seems to be caused by the expansion of coastal water to the Cheju Strait.

• Journal of Korean Society on Water Environment
• /
• v.29 no.6
• /
• pp.754-761
• /
• 2013

Urban floods are usually caused by the lack of drainage capacity. Hence, sewer capacity expansion methodology by replacing small pipes with bigger ones is primarily applied as a flood control measure. However, this approach is often unreasonable because of the costs and time involved. Thus, the installation of underground rainwater storage tanks with the two advantages of flood control and water conservation is proposed. This study compared the effectiveness of flood control by both the sewer expansion methodology and rainwater storage tanks using the Storm Water Management Model. Three cases were simulated in this study. The first case analyzed flood reduction by the storm sewer expansion methodology. The simulation results indicate that the overflow volume from manholes was reduced by 49% with this methodology. The second case analyzed flood reduction by installation of rainwater storage tanks. The simulation results indicate that the overflow volume was reduced by 62%. However, these two cases could not prevent urban floods completely. Hence, the third case analyzed the joint application of the storm sewer expansion methodology and rainwater storage tanks. In this simulation, flooding did not occur. Consequently, the results of this study clearly show that underground rainwater storage tanks are more effective for flood control than capacity expansion of storm sewer. Furthermore, the joint application of these two flood control measures is more effective than their separate application.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.11a
• /
• pp.79-83
• /
• 2005

In the reinforced concrete structure, Even if speak that water leakage occurrence is no problem to material, there is a lot of reasons construction factor, material damage by behavior structure, properties of matter change by years and water leakage part by environment condition. so, waterproofing technological consideration should be gone ahead. In this research, we will study about stick performance, concrete surface adhesive, damage and blow. we will check all things and test it. The stick expansion type complex of flexible material passed on result of standard. It is conducive to concrete of durability by waterproofing layer performance demobilitation technology on the water leakage structure for solution of problem and repair