• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.4
• /
• pp.327-333
• /
• 2023

The water gas shift reaction was carried out using the commercial catalyst pellet and the simulated gases expected to occur from waste plastic gasification. In the water gas shift reaction, the high temperature shift reaction and the low temperature shift reaction were continuously performed with CO:H₂O ratio of 1:2, 1:2.5, and 1:3, and the CO conversion and H₂ increase rate were evaluated. The H₂ increase rate increased in order to CO:H₂O ratio of 1:3 > CO:H₂O ratio of 1:2.5 > CO:H₂O ratio of 1:2. The CO conversion showed a high value of more than 97% at each CO:H₂O ratio. The water gas shift reaction at a CO:H₂O ratio of 1:3 showed the highest H2 increase rate and CO conversion.

• Clean Technology
• /
• v.15 no.3
• /
• pp.147-153
• /
• 2009

Waste three-way catalysts were remanufactured by ultrasonic wave treatment followed by active component re-impregnation and the catalytic activities and surface properties of remanufactured catalysts were measured at various remanufacturing conditions. In case of the catalyst prepared by ultrasonic wave cleaning, the optimal period for elimination of surface contaminants from the waste catalyst was found to be about 5 minutes. The proper re-impregnation amounts of the active components for the best catalytic performance were investigated and the catalytic performance tests were also carried out with various temperature for the total hydrocarbon (THC), carbon monoxide (CO) and nitrogen oxides (NOx) conversions. The experimental results showed that the catalytic performances of the remanufactured catalysts were recovered almost the same level as those of the fresh catalyst except those of the NOx conversion.

• New & Renewable Energy
• /
• v.5 no.4
• /
• pp.52-58
• /
• 2009

Upgrading of pyrolysis wax oil using HZSM-5 catalyst has been conducted in a continuous fixed bed reactor at $450^{\circ}C$, 1hour, LHSV 3.5/h. The catalytic degradation was studied with a function of catalyst amount and reaction temperature. The raw pyrolysis wax oil shows relatively high boiling point distribution ranging from around $300^{\circ}C$ to $550^{\circ}C$, which has considerably higher boiling point distribution than that of commercial diesel. The catalytic degradation using HZSM-5 catalyst shows the high conversion of pyrolysis wax oil to light hydrocarbons. The liquid product obtained shows high gasoline range fraction as around 90% fraction and considerably high aromatic fraction in liquid product. Here, the experimental variable such as catalyst amount and reaction temperature was influenced on the product distribution.

• Resources Recycling
• /
• v.22 no.2
• /
• pp.53-61
• /
• 2013

Since the 2000s, to start inducement of SCR(Selective Catalytic Reduction) denitrification facility by large scale companies which are emitted large amount of nitrogen oxides such as power plants, combined heat and power plant, incinerators and chemical plants due to take effect the regulation of stationary sources of nitrogen oxide(NOx), and the total amount of discharged pollutants, such as regulatory gradually emissions regulations are being strengthened and the expanded coverage due to the use of SCR denitrification catalyst is a growing trend. Since 2010 due to the new catalysts to replace the already installed power plants and incinerators due to inactive, and catalytic denitrification SCR waste catalyst waste as a resource rather than the development of technologies for recycling situation is urgently needed. In this study, analyzed paper and patent for recycling technologies of waste catalyst. The range of search was limited in the open patents of USA (US), European Union (EP), Japan (JP), Korea (KR) and SCI journals from 1975 to 2012. Patents and journals were collected using key-words searching and filtered by filtering criteria. The trends of the patents and journals was analyzed by the years, countries, companies, and technologies.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.5
• /
• pp.663-670
• /
• 2004

The catalytic oxidation of benzene, toluene and xylene over a spent industrial catalyst (Pd-based) was investigated in a fixed bed flow reactor system. According to the priming condition, the properties of a spent Pd-based catalyst were characterized by XRD(X-ray diffraction). BET(Brunauer-Emmett-Teller) and ICP(Inductively coupled plasma). When air was used as a primer, optimum priming temperature was found to be 200$^{\circ}C$, and the catalytic activity decreased as the priming temperature increased. When a spent Pd-based catalyst primed with air at 200$^{\circ}C$ was re-treated with hydrogen at 200$^{\circ}C$, 300$^{\circ}C$ or 400$^{\circ}C$, respectively, the catalytic activity increased and thermal effect were negligible. $HNO_3$ aqueous solution priming resulted in slight decrease of the catalytic activity, with little effects on $HNO_3$ concentrations. The activity of a spent Pd-based catalyst with respect to VOC molecule was observed to follow sequence: xylene> toluene> benzene. Benzene. toluene and xylene could be removed to almost 100% by a spent Pd-based catalyst primed with hydrogen.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.2 no.1
• /
• pp.71-75
• /
• 1984

NiNH$_{4}PO_{4}$ was Prepared from waste Ni catalyst used in hydrogenation of oil and fat, NiNH$_{4}PO_{4}$ was calcined at different temperature respectly 800, 1000, 1100$^{\circ}$C to prepare Nickel yellow. The results from this experiment are summerized as follow: 1) Nickel yellow formed at 1100$^{\circ}$C was most clearness yellow color from color analyzer data. 2) Nickel yellow was consist of ${\alpha}-Ni_{2}P_{2}O_{7}$, $Ni_{3}(PO_{4})_{2}$ from X-ray diffraction analysis. 3) The endothermic pick at 100$^{\circ}$C and exotherwic pick about 1050$^{\circ}$C on calcination of NiNH$_{4}PO_{4}$ were checked in DTA (difference thermal analysis data)

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.3
• /
• pp.146-151
• /
• 2013

In this study, the effect of addition of waste glassy slag produced from recycling of spent catalyst (denoted as waste glass hereafter) on the physical properties of artificial aggregates made of coal bottom ash and dredged soil (7 : 3 by weight base) was evaluated. Especially, the bloating behavior of artificial aggregates was analyzed by performing the relation study between the apparent density, water absorption and microstructure. The apparent density of artificial aggregates increased slightly with sintering temperature at $1050{\sim}1150^{\circ}C$, but decreased above $1150^{\circ}C$ showing bloating phenomenon. The bloating behavior of artificial aggregates was decreased so the apparent density increased with amount of waste glass added. Also, the water absorption of artificial aggregates decreased with sintering temperature. Above $1200^{\circ}C$, big fissure and much liquid were formed at the surface of artificial aggregates and these phenomena could be suppressed by increasing amount of waste glass added. The artificial aggregates fabricated in this study had an apparent density of 1.1~1.6 and water absorption of 8~22 % which meet KS requirements for the artificial lightweight aggregates.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.324-330
• /
• 2019

To recycle raw fly ash (RFA), a waste from thermal power plants, it was used to prepare solid catalysts which have many advantages compared with homogenous catalysts. When biodiesel was produced from soybean oil using RFA, only 1.2% of biodiesel conversion was obtained. A metal hydroxide, NaOH, KOH or $Ca(OH)_2$, was mixed with the acid-treated fly ash (ATFA), and the mixture was calcined at $700^{\circ}C$ for 3 h to prepare the solid catalyst. The solid catalyst prepared by mixing ATFA with NaOH, designated as SC-Na, showed a better performance than those prepared by mixing ATFA with KOH or $Ca(OH)_2$, respectively. The optimal mass ratio of ATFA with NaOH was 1:3, at which the proportion of $Na_2O$ increased to 60.2% in SC-Na, and 97.8% of biodiesel conversion was achieved under optimal reaction conditions (2 w% SC-Na relative to oil and 5 mL-methanol/g-oil at $50^{\circ}C$ for 4 h). Finally, a batch operation was repeatedly carried out to test the feasibility of reusing the solid catalyst, and more than 96% biodiesel conversion was stably achieved for the third round of operations. This study shows that RFA was successfully recycled to solid catalysts through a simple preparation method, and the solid catalyst was reused for the production of biodiesel with high conversion.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.3
• /
• pp.683-693
• /
• 2017

Transport biofuels have been recognized as a promising means to resolve the following issues like global warming, oil depletion and environmental pollutions. Among various biofuels, biodiesel has several advantages such as less emission of air pollutants and higher cetane values compared to diesel oil. Demand for biodiesel in Korea is increasing that leads to higher dependence on the imported feedstocks. Therefore, it is important to utilize the waste materials collected domestically for biodiesel production. Food waste oil collected in waste treatment facility has not been used for biodiesel production due to high free fatty contents in the oil. In this work, biodiesel conversion of food waste oil by Amberlyst 15 was studied. Synthetic and actual food waste oils have been used in the study. First, the effects of the major operating parameters including reaction temperature, methanol to oil molar ratio and catalyst loading on the conversion rates and yields were determined with synthetic waste oil. Kinetic modelling work was also done to determine the activation energy of the reaction. From the work, optimization reaction conditions were determined to be 383K, 1: 26.1 for methanol molar ratio to oil, 10 wt.% for catalyst loading and 360 min for reaction time. Activation energy of the reaction is determined to be 29.75 kJ/mol, lower than those reported in the previous works. So the solid catalyst, Amberlyst 15, was more efficient for esterification than the solid catalysts employed in the other works. Agitation rates have the negligible effects on the conversion rates and yields. With the identified optimization conditions, conversion of the actual food waste oil was also carried out. The esterification yield of actual food waste oil in 60 min was 13% lower than that of synthetic waste oil but the final yields in 240 min were similar each other, 98.12% for synthetic oil and 97.62% for actual waste oil.

• New & Renewable Energy
• /
• v.17 no.2
• /
• pp.32-39
• /
• 2021

The optimal conditions for producing levulinic acid from office waste paper were investigated. Glucose was produced by enzymatic hydrolysis and its yield maximized by varying the soaking time of the substrate and amounts of enzyme and substrate. The optimal conditions to produce levulinic acid using the hydrolysate were determined by response surface methodology, with reaction temperature and catalyst (sulfuric acid) concentration as independent variables. The production model was assessed with an ANOVA regression analysis, and the results indicate its suitability for levulinic acid production (p, F, and lack-of-fit values were 0.003, 20.1, and 0.058, respectively). The optimal conditions were a reaction time of 56.27 min and catalyst concentration of 5.9% with a predicted yield of 2.588 g/L. We verified the findings under the same conditions and obtained 2.323 g/L of levulinic acid.