• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.924-929
• /
• 2002

To recycle waste materials, this work was focused on development of glass-ceramic from incinerator fly ash with a large content of Cl and its physical property was evaluated. In the process, water washing as a pre-treatment before melting the fly ash was used to remove large amount of Cl component in the ash and to reduce melting temperature. As a result, glass was obtained at below $100^{\circ}C$ compared to the melting temperature before washing the ash. Also, internal crystallization occurred under single stage heat treatment (at $850-950^{\circ}C$ for 20-340min) without adding other materials into the ash. It was shown that the glass-ceramic was composed of four crystals, diopside, anorthite, akermanite, and unknown phase. Hardness of 8.3GPa was found in the glass-ceramic, which is a high value compared to reported others. Thus, the present process suggests that a good glass-ceramic produced from an incinerator ash could be applicable for structural materials in terms of economic and environmental points.

• Textile Coloration and Finishing
• /
• v.21 no.6
• /
• pp.29-38
• /
• 2009

Natural dyes seem to be more profitable on human and environment, and recently they could be considered as a better alternative to synthesized dyes. The aim of the current work was to investigate the dyeing property and antimicrobial activity of commercial cotton fabrics dyed with kumazasa (usually called in japan) which is known as conventional japan bamboo leaves. Actually, the dyeability and antimicrobial property of dyed fabric with natural mordant/dyeing was compared with synthetic mordant/dye process. The results of this study obtained are as follows. The apparently colour of kumazasa leaves extract dyed fabrics showed with light green or slightly yellow-green. In colorfastness to washing, ${\Delta}E$ and K/S values of dyed fabrics with natural chitosan as mordant used was shown to be more excellent results, than was synthetic mordant used. However, the decrease rate was recorded nearly 50% when washing repeated 20 cycles. In result of antimicrobial effect for bacteria, the dyed fabrics didn't show the significant antimicrobial activity to the both dyed with and without mordant. Results of this investigation considered that low-cost, natural, bio-mordant are relatively effective in natural coloration.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.19-24
• /
• 2003

Recently, various efforts to make more speedy and precision machine tool to improve productivity and also various efforts to solve environmental problem are going on, so that dry cutting in manufacturing industry, which needs environmental conscious design and development of manufacturing technique, is becoming a very important assignment to solve. Because dry cutting does not use cutting fluid, we need other methods that can be used instead of cutting fluid, which does cooling, lubricating, chip washing, and anti-corrosion. Especially, because turning is a continuous work, the consideration of tool life and surface roughness due to continuous heat and poor lubrication is important. The purposes of this paper are the consideration of how well the compressed air can work instead of cutting fluid, and also the development of the method to select the optimum machining condition by the minimum numbers of experiments through the Taguchi method.

• Korean journal of food and cookery science
• /
• v.13 no.4
• /
• pp.402-409
• /
• 1997

Understanding the satisfaction and dissatisfaction of employees has been deemed important for smooth and efficient food service management. The aim of this study was to examine the relationship between the dishwashing employees' job satisfaction and the operational and managerial factors in hospital foodservice systems. A survey of twenty conventional hospital food service systems was undertaken and detailed information was collected from 280 dishwashing employees through mailed questionnaires. Dishwashing employees' satisfaction was evaluated by measuring their job attitudes towards four aspects of their job using the modified Job Description Index (JDI). Descriptive analysis and Pearson product moment correlation analysis were used to analyze the data. The dishwashing workers were found to be more satisfied with their interpersonal relations with co-workers than with work content, pay or promotional opportunities. The demographic variables including education, type of employment and work experience were significantly related to job satisfaction. As the ratio of supervisors to dishwashing workers increased, the degree of satisfaction in dishwashing workers increased significantly.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.49-55
• /
• 2011

Recently, various efforts to make more speedy and precision machine tool to improve productivity and also various efforts to solve environmental problem are going on, so that dry cutting in manufacturing industry, which needs environmental conscious design and development of manufacturing technique, is becoming a very important assignment to solve. Because dry cutting does not use cutting fluid, we need other methods that can be used instead of cutting fluid, which does cooling, lubricating, chip washing, and anti-corrosion. Especially, because turning is a continuous work, the consideration of tool life and surface roughness due to continuous heat and poor lubrication is important. The purposes of this paper are the consideration of how well the compressed air can work instead of cutting fluid, and also the development of the method to select the optimum machining condition by the minimum numbers of experiments through the Taguchi method.

• The Research Journal of the Costume Culture
• /
• v.4 no.3
• /
• pp.337-347
• /
• 1996

The work-man's Uniform should be coincident with the image of his firm and accounted of the function according s its purpose. We made questions to 404 workers at 8firm in our country through the questionnaire papers to know about a work-man's uniform and researched whether the satisfactory in wearing his uniform had relation with his type of business, grade, carrier, age, marriage, and monthly income. The results of this study is as follows; 1. In the case of wearing the uniform many workers answered they always wore their uniform in the firm. It was shown that the office workers wore their uniform much more than workers in the production department. The longer the time working, the older age, the lower grade of school career are, he more workers wear. the order of the importance for he uniform was the function, the symbol, the originality, and the fashion. The longer their career in the firm was, the more important the function of their uniform was. 2. The order of dirty pat in taking care of the uniform was cuffs, color, the front of part in an upper garment and below the knee, the hip in pants It was very easy for the workers in the experts, or administrators and office workers than others to be dirty in the cuffs part of the uniform. Worn part of the uniform showed highest cuffs in an upper garment and a zipper in pants. The order of cleaning the uniform was washing by water, no ironing, and cleaning in their house.

• Journal of Fashion Business
• /
• v.15 no.5
• /
• pp.43-54
• /
• 2011

Digital Textile Printing(DTP) is appropriate for quick response system(QRS) and is closely connected with high value added fashion industry. Fashion products of high price are mainly silk and cotton. For high quality DTP products, it is important to optimize the parameters of media, pre and after-treatment, ink, printer, etc. DTP for these two fiber materials is also accompanied certainly with steaming as after-treatment process for coloration. Role of steam is like water in exhaustion dyeing. Steam can diffuse dye or ink in printing paste to fiber. Quality of DTP products depend on after-treatment processes such as steaming, washing, drying. Current production amount of DTP is smaller than one of conventional textile printing. However conventional after-treatment system has been using so far. This is mismatched with DTP in terms of process efficiency, spot work of small lot, quality control. In this study, continuous after-treatment system has been suitably designed for DTP that washing and drying are available after steaming. So, It is possible to improve efficiency of DTP process. Especially, the effects of after-treatment process, such as temperature of heat drum, steaming time on printability, color difference, color fastness were examined. Two types of samples(cotton knit and silk fabrics) were used. The results were obtained as follows : First, there is no a wide difference between the K/S values of cotton and silk treated with continuous after-treatment system and those of sample treated with conventional printing after-treatment method. So it is more effective to use the continuous after-treatment system than conventional printing after-treatment system in case of the daily throughput of 1,000 yards below. Second, after continuous after-treatment for DTP, K/S values were increased and lightness($L^*$) values were decreased. ${\Delta}E$ values were below 2.3. Third, DTP samples treated with continuous after-treatment system were tested for fastness(washing, light, rubbing). Grades of fastness(washing, light, rubbing) were above 3 grade.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.2
• /
• pp.276-280
• /
• 2007

In this work, caffeine and some catechin compounds + C, EC, EGC, and EGCG were extracted from green tea by using molecular imprinted polymers (MIP) as sorbent materials in a solid-phase extraction (SPE) process known as MISPE (molecular imprinted solid-phase extraction). For synthesis of MIP, caffeine was employed as the template, MAA as the monomer, EGDMA as the crosslinker, and AIBN as the initiator. A solution of caffeine (0.2 mg/mL in methanol) was utilized in the solid extraction cartridges following loading, washing, and elution procedures with acetonitrile, methanol, and methanol-acetic acid (90/10, %v/v) as the solvents, respectively. This solid-phase extraction protocol was applied for the extraction of caffeine and some catechin compounds from green tea. A comparison was made between the results obtained with the MIP cartridges and a traditional C18 reversed-phase cartridge. It was thereupon found that the recovery of caffeine by the MIPbased sorbent used in this work was almost two and four times greater than that by a commercially available C18 material. A quantitative analysis was conducted by high performance liquid chromatography (HPLC) using a C18 column (5 μm, 250 × 4.6 mm) with methanol/water (40/60, %v/v) as the mobile phase at a flow rate of 0.5 mL/min.

• Journal of Korean Biological Nursing Science
• /
• v.21 no.1
• /
• pp.37-45
• /
• 2019

Purpose: This descriptive research was on hand dermatitis in clinical nurses. Nurses often have a high rate of hand dermatitis with several factors associated with the dermatitis. The factors analyzed in this study included; general characteristics, work-related factors, hand washing, and allergies relate to hand dermatitis. Methods: Data were collected from April to May 2016. The subjects were nurses who had worked 12 months or more in a University Hospital. They voluntarily gave their consent for the research. The Symptombased questionnaires were sent to 220 nurses and 199 responses were returned. Collected data were analyzed using frequency, percentage, mean, standard deviation, ${\chi}^2-test$, and logistic regression analysis using SPSS 23.0. Results: Prevalence of dermatitis in nurses was 48.2%. Nurses who had worked for over three years were twice more likely to suffer hand dermatitis than nurses who had worked for 3 years or less (adjusted odds ratio [adj. OR]= 1.97, p= .036). Nurses who used alcohol sponge swabs more than 20 times per shift were 2.5 times more likely to suffer hand dermatitis as compared to those who used them less times (adj. OR = 2.51, p= .023). Conclusion: Results revealed that about a half of the clinical nurses suffered from hand dermatitis, hence it is crucial to find appropriate interventions for dermatitis prevention. This concern needs to be addressed especially in nurses who have more work experience and use more alcohol sponge swabs.

• Journal of Environmental Health Sciences
• /
• v.22 no.1
• /
• pp.45-50
• /
• 1996

The application of HACCP system, which was adopted by Codex Alimentarius Committee for the safe meat and poultry production, is one of the urgent task for competing in the world trade markets. But there have been no useful analytical studies to identify the causes of contamination in the poultry meat processing plants in Korea. This study was conducted to investigate the potential hazards during the operations by the microbiological examination for the poultry meat processing plant (20,000 birds capacity a day) located in Kangwon province. In spite of air contamination of work places, it may not directly affect the surface contamination of poultry meats. But the risk of Campylobacter jejuni/coli contamination was high. The number of total count was decreased about ten times, but remarkable changes of microbial contamination could not be recognized in each procedure during the operations. The washing water was already contaminated as much as $10^{3-6}CFU/ml$ in SPC before the operations. It means that to keep water tanks hygienic is a primary step to prevent the occurrences of microbial contamination. The overflow and recirculation of water in scalding, washing, and chilling was aslo an important factor for a hygienic control. Based on this study, the followings could be regarded as an important factors for hygenic control in the poultry slaughtering plants on a small scale. The temperature of water used for scalding should be constantly maintained on a required temperature, and the overflow rate of 1~1.5 liter per bird. The carcass surface and the body cavity should be washed thoroughly and the cross-contamination due to facilities, workers, and tools should be prevented. The chilling water sholud be maintained under 5$\circ$C of temperature with ice and overflow, and residual chlorine level of 50 ppm.