• The Journal of Engineering Geology
• /
• v.25 no.4
• /
• pp.577-585
• /
• 2015

Contamination of soil due to an oil spill influences its subsequent behavior. An investigation was conducted to study the effect of oil viscosity on compaction characteristics, coefficient of permeability, and shear strength. Water permeability was also determined by using Kerosene, Engine oil, and Crude-oil as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. Direct shear test was conducted to investigate the effect of oil in the pore space in sandy ground. angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.5
• /
• pp.51-58
• /
• 2010

This study was done to recommend a method for conserving the habitat of Amblyotropis verna grown naturally in campus of the Kyungpook National University at Daegu city. Vegetation characteristics and morphological characteristics of each individual were analyzed for the condition of the population at the growing season from May to June in 2010. Totally 11 vegetation data were collected and analyzed, and one vegetation community including Amblyotropis verna (Amblyotropis verna-Zoysia japonica community) was found. We found that the growing condition was not good with severe stamping and disturbance. The location-determining method by PCoA analysis showed the physical texture in soil was a critical factor determining the spatial distribution of the Amblyotropis verna-Zoysia japonica community. And the analysis of morphological characteristics found that light condition and soil hardness were the main ecological factor determining the size and form of each individual. Finally, this study recommend that minimizing impacts by human stamping and artificial disturbance and reducing the water stress were the best ways for the conservation of Amblyotropis verna habitats.

• Textile Coloration and Finishing
• /
• v.10 no.3
• /
• pp.10-19
• /
• 1998

This paper investigates the change of mechanical properties and thermal shrinkage in commercial multi-filament PET(polyethylene terephthalate) , namely, regular yarn, POY, DTY and composite yarn. To determine changing the effects of processing steps, these were examined at three steps process simulation conditions. The first step is sizing simulation$(S-1\;step\;:\;130^\circ{C}\times2\;min$., hot air treatment under 0.1 gf/d load), the second step is scouring simulation$(S-2\;step\;:\;100^\circ{C}\times20\;min$., boiling water treatment under free tension)and final step is setting simulation$(S-3\;step\;:\;180^\circ{C}\times2\;min$., hot air treatment under free tension). Regular yarn in multi-step treatment showed higher shrinkage at S-3 step and DTY showed higher in at S-1 step. While POY was relaxed at S-1 step, composite yarn showed different shrinkage properties depending on composite yarn type. Mechanical properties showed good relationship with shrinkage : high shrinkage makes initial modulus decrease and bleating strain increase. It also makes decreasing yield strain and yield stress decrease.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.151-154
• /
• 2017

In this article, we investigated the various influencing factors that degraded the lifetime of suspension insulators in 154 kV transmission lines, and showed the possible solutions to avoid such breakdowns. With respect to achieve safety, reliability and aesthetical considerations, the characteristics of transmission and distribution network power cables should be improved. Suspension insulators are particularly important to study, as they have developed to be the main component of transmission lines due to their ability to withstand the electrical conductivity of high-voltage power transmission. Suspension insulators are mostly made from glass, rubber and ceramic material due to their high resistivity. In Korea, porcelain suspension insulators are typically used in the transmission line system, as they are cheaper and more flexible compared to other types of insulators. This is effective from preventing very high and steep lightening impulse voltages from causing the breakdown of suspension insulators used in power lines. Other influential factors affect the lifetime of suspension insulators that we studied include temperature, water moisture, contamination, mechanical vibration and electrical stress.

• Safety and Health at Work
• /
• v.8 no.4
• /
• pp.327-328
• /
• 2017

Despite provision of drinking water as the most common method of occupational heat stress prevention, there remains confusion in hydration messaging to workers. During work site interactions in a hot and humid climate, workers commonly report being informed to consume tepid fluids to accelerate rehydration. When questioned on the evidence supporting such advice, workers typically cite that fluid absorption is delayed by ingestion of chilled beverages. Presumably, delayed absorption would be a product of fluid delivery from the gut to the intestines, otherwise known as gastric emptying. Regulation of gastric emptying is multifactorial, with gastric volume and beverage energy density the primary factors. If gastric emptying is temperature dependent, the impact of cooling is modest in both magnitude and duration (${\leq}5$ minutes) due to the warming of fluids upon ingestion, particularly where workers have elevated core temperature. Given that chilled beverages are most preferred by workers, and result in greater consumption than warm fluids during and following physical activity, the resultant increased consumption of chilled fluids would promote gastric emptying through superior gastric volume. Hence, advising workers to avoid cool/cold fluids during rehydration appears to be a misinterpretation of the research. More appropriate messaging to workers would include the thermal benefits of cool/cold fluid consumption in hot and humid conditions, thereby promoting autonomy to trial chilled beverages and determine personal preference. In doing so, temperature-based palatability would be maximized and increase the likelihood of workers maintaining or restoring hydration status during and after their work shift.

• Nuclear Engineering and Technology
• /
• v.48 no.2
• /
• pp.545-553
• /
• 2016

The failure probabilities of the reactor pressure vessel (RPV) for low temperature over-pressurization (LTOP) and cool-down transients are calculated in this study. For the cool-down transient, a pressure-temperature limit curve is generated in accordance with Section XI, Appendix G of the American Society of Mechanical Engineers (ASME) code, from which safety margin factors are deliberately removed for the probabilistic fracture mechanics analysis. Then, sensitivity analyses are conducted to understand the effects of some input parameters. For the LTOP transient, the failure of the RPV mostly occurs during the period of the abrupt pressure rise. For the cool-down transient, the decrease of the fracture toughness with temperature and time plays a main role in RPV failure at the end of the cool-down process. As expected, the failure probability increases with increasing fluence, Cu and Ni contents, and initial reference temperature-nil ductility transition ($RT_{NDT}$). The effect of warm prestressing on the vessel failure probability for LTOP is not significant because most of the failures happen before the stress intensity factor reaches the peak value while its effect reduces the failure probability by more than one order of magnitude for the cool-down transient.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.5
• /
• pp.31-36
• /
• 2010

When corrugated board is folded at the severely low humidity condition, crack can occur along the scored (or creased) lines of linerboard. This phenomenon is called as score (or crease) crack. It is mainly resulted from the excessive concentration of stress on the outer layer of linerboard. To overcome score crack, many approaches including the installation of constant temperature and humidity system, displacement of low grade raw material by long and strong fibers, or application of water have been tried. We examined the effect of the weight fraction of top layer in two-ply sheet, freeness of top layer stock and wet pressing on strain and elastic modulus of sheet to prevent score crack. Lower freeness and higher press load increased the density and elastic modulus of sheet. Pressing load over the $50kgf/cm^2$, however, decreased the strain of sheet. The weight fraction of top layer had positive effect on strain as well as elastic modulus without increasing the density of sheet.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.321-324
• /
• 2005

The main purpose of the present study has been placed on investigating the effects of controlled rolling and cooling on the microstructures and mechanical properties of C-Si-Mn-V steels for cold forming. The steels were manufactured in vacuum induction melting(VIM) furnace and casted to 1.1ton Ingots and the ingots were forged to $\Box150$ billet. The forged billets were reheated in walking beam furnace and rolled to coil, the stocks were rolled by Controlled Rolling and Cooling Technology (CRCT), so rolled at low temperature by water spraying applied in rolling stage and acceleratly cooled before coiling. Rolled coils were cold drawed to the degree of $27\%$ of area reduction without heat treatment. Microstructual observation, tensile test, compression test and charpy impact tests were conducted. The mechanical properties of the steels were changed by area reduction of cold drawing and it is founded that there are optimum level of cold drawing to minimize compression stress for these steels. From the result of this study, it is conformed that mechanical properties and microstructure of C-Si-Mn-V steels for cold forming were enhanced by accelerated cooling and founded optimum level of cold drawing.

• Biomolecules & Therapeutics
• /
• v.4 no.2
• /
• pp.111-121
• /
• 1996

Antiulcer effects of Artemisia herba extract (DA-9601) were evaluated in various types of experimental gastric ulcer induced in rats. And the effects of DA-9601 on mucus, basal and stimulated gastric acid secretion were also investigated in rats. DA-9601 (12.5∼400 mg/kg, p.o.) prevented the formation of gastric ulcers induced by 60% EtOH in 150 mM HC1, restraint water immersion stress, platelet activating factor (PAF), aspirin in 150 mM HCI with Pylorus-ligation and indomethacin. DA-9601 (4∼400 mg/kg, p.o.) significantly accelerated the healing rate of acetic acid-induced gastric ulcer and significantly stimulated mucus secretion in a dose-dependent manner. DA-9601 (20∼200 mg/kg, i.d.), however, did not inhibit basal gastric acid secretion in pylorus ligated rats and DA-9601 (200 mg/kg, i.d.) failed to influence histamine-, pentagastrin- and carbachol- stimulated gastric acid secretion. These results suggest that DA-9601 has inhibitory action on gastric lesion and ulceration through increasing mucus secretion in the stomach of rats without influencing basal and stimulated gastric acid secretion.