• Steel and Composite Structures
• /
• 제4권6호
• /
• pp.419-435
• /
• 2004

The safety level of a structural system designed per code specifications can not be inferred directly from the reliability of members due to the load redistribution and nonlinear inelastic structural behavior. Comparison of the system and member reliability, which is scarce in the literature, is likely to indicate any possible inconsistency of design codes in providing safe and economical designs. Such a comparative study is presented in this study for moment resisting two-dimensional steel frames designed per AISC LRFD Specifications. The member reliability is evaluated using the resistance of the beam-column element and the elastic load effects that indirectly accounts for the second-order effects. The system reliability analysis is evaluated based on the collapse load factor obtained from a second-order inelastic analysis. Comparison of the system and member reliability is presented for several steel frames. Results suggest that the failure probability of the system is about one order of magnitude lower than that of the most critically loaded structural member, and that the difference between the system and member reliability depends on the structural configuration, degree of redundancy, and dead to live load ratio. Results also suggest that the system reliability is less sensitive to initial imperfections of the structure than the member reliability. Therefore, the system aspect should be incorporated in future design codes in order to achieve more reliability consistent designs.

• Journal of the Optical Society of Korea
• /
• 제18권1호
• /
• pp.60-64
• /
• 2014

We report the generation of 3.3-mW single-cycle terahertz (THz) pulses at 1-kHz repetition rate via optical rectification in MgO-doped prism-cut stoichiometric LiNbO3. Efficient pulse-front tilting of 800-nm pulses was realized by an optimized single-lens focusing scheme for radially-symmetric propagation of THz beams. In this geometry, nearly-diffraction-limited THz Gaussian beams with electric field strength as high as 350 kV/cm were generated. The pump-to-THz energy conversion efficiency of $1.36{\times}10^{-3}$ and the extremely high signal-to-noise ratio of ~1:15000 achieved are among the best results for 1-kHz single-cycle terahertz pulse generation ever demonstrated in room temperature operation.

• Structural Engineering and Mechanics
• /
• 제43권1호
• /
• pp.31-51
• /
• 2012

This paper presents a computational study that explores the design of rigid steel frames by considering construction related costs. More specifically, two different aspects are investigated in this study focusing on the effects of (a) reducing the number of labor intensive rigid connections within a frame of given geometric layout, and (b) reducing the number of different member section types used in the frame. A genetic algorithm based optimization framework searches design space for these objectives. Unlike some studies that express connection cost as a factor of the entire frame weight, here connections and their associated cost factors are explicitly represented at the member level to evaluate the cost of connections associated with each beam. In addition, because variety in member section types can drive up construction related costs, its effects are evaluated implicitly by generating curves that show the trade off between cost and different numbers of section types used within the frame. Our results show that designs in which all connections are considered to be rigid can be excessively conservative: rigid connections can often be eliminated without any appreciable increase in frame weight, resulting in a reduction in overall cost. Eliminating additional rigid connections leads to further reductions in cost, even as frame weight increases, up to a certain point. These complex relationships between overall cost, rigid connections, and member section types are presented for a representative five-story steel frame.

• Structural Engineering and Mechanics
• /
• 제42권4호
• /
• pp.471-488
• /
• 2012

An efficient one dimensional finite element model has been presented for the dynamic analysis of composite laminated beams, using the efficient layerwise zigzag theory. To meet the convergence requirements for the weak integral formulation, cubic Hermite interpolation is used for the transverse displacement ($w_0$), and linear interpolation is used for the axial displacement ($u_0$) and shear rotation (${\psi}_0$). Each node of an element has four degrees of freedom. The expressions of variationally consistent inertia, stiffness matrices and the load vector are derived in closed form using exact integration. The formulation is validated by comparing the results with the 2D-FE results for composite symmetric and sandwich beams with various end conditions. The employed finite element model is free of shear locking. The present zigzag finite element results for natural frequencies, mode shapes of cantilever and clamped-clamped beams are obtained with a one-dimensional finite element codes developed in MATLAB. These 1D-FE results for cantilever and clamped beams are compared with the 2D-FE results obtained using ABAQUS to show the accuracy of the developed MATLAB code, for zigzag theory for these boundary conditions. This comparison establishes the accuracy of zigzag finite element analysis for dynamic response under given boundary conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.251-254
• /
• 2001

In this paper, we analysed the properties change of electric wire when the thermal stress was applied to NFR-8 and FR-PVC [600] wire. Measurement is made of the attenuation of a light beam by smoke accumulating with in a closed chamber due to nonflamining pyrolytic decomposition and flaming combustion. Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density a measurement characteristic of the concentration of smoke. Referenced documents were ASTM E662 standard test method for specific Ds generated by solid materials. The furnace control system shall maintain the required irradiance level under steady-state condition with the chamber door closed of 2.5${\pm}$0.04[w/$\textrm{cm}^2$] for 20 min. According to the results of the smoke density analysis of NFR-8 and FR-PVC the highest decomposition flaming smoke density range of NFR-8 and FR-PVC were 7.2 to 77.5 and 51.1 respectively. Nonflaming smoke density range of NFR-8 and FR-PVC were 100.4 to 112.2 and 126.5 to 398.8. The amount of carbon monoxide generated was found to be much higher in FR-PVC decomposition than in NFR-8 due to incomp1ete combustion of FR-PVC which has high content of carbon in compound.

• Transactions on Electrical and Electronic Materials
• /
• 제1권3호
• /
• pp.23-28
• /
• 2000

A block-oxide layer was formed on the surface of Cu-based leadframe by chamical oxidation method in order to enhance the adhesion strength between Cu-based leadframe and epoxy molding compound (EMC) Using sandwiched double cantilever beam (SDCB) specimens, the adesion strength was measured in terms of interfacial fracture toughness, G$\sub$IC//Results showed that the black-oxide layer was composed of two kinds of layers: pebble-like Cu$_2$O layer and acicular CuO layer, At the initial stage of oxidation the Cu$_2$O layer was preferentially formed and thickened up to around 200 nm whithin 1 minute of the oxidation time. Then the CuO layer started to from atop of the Cu$_2$O layer and thickened up to around 1300 nm until 20 minutes. As soon as the CuO layer formed, the thickness of Cu$_2$O layer began to reduce and finally reached to around 150 nm. The pre-cleaned and the Cu$_2$O coated leadframes showed almost no adhesion of EMC, however, as the CuO precipitates appeared and became continuous, G$\sub$IC/ increased up to around 80 J/㎡. Further oxidation raised G$\sub$IC/ up. to around 100 J/㎡.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.106-115
• /
• 2007

In this study, first, child headform model was built up, satisfying requirement in the headform validation test. Also, for decreasing both acceleration peak and deformation, a new hood with dome shaped forming in inner panel was investigated. Next, headform impact, complying with draft of EEVC W/G 17, on the central portion of the newly proposed hood were simulated for a steel hood and three aluminum hoods with different thickness for examining the material and thickness effect on HIC value and inner panel deformation. The analysis results explained that aluminum hoods with dome shaped forming in inner panel were highly promising not only for meeting headform safety regulations but also for leading to weight savings. Finally, hood edge design technology in order to reduce pedestrian injury due to the high stiffness of beam type edge and the rigid support, was discussed. Various types of the foam filled edge were designed and their headform safety performance were evaluated. The edge structure with foam filled in upper one third of section exhibited excellent results.

• 기술혁신학회지
• /
• 제7권3호
• /
• pp.641-656
• /
• 2004

L Company is producing the second sept pin, Shadow Mask which is the chief part of CRT in W, Monitor. Inside of the CRT pan, Shadow Mask leads the electronic beam to express the three primary colors; red, green, blue, and it is the core part to embody the colors. In the etching process, it produces this part with manufacturing by eroding the iron chloride. Even though the iron chloride is harmless to human body. it is necessary to diminish the amount of it on the view of preservation of environment. In addition, by studying the method of the dispossed liquid process, cutting down the manufacturing cost is a necessary task on the aspect of reconsideration of competitive business. This study shows the case that through the six sigma innovation activity, it reforms the following the former processing flow, and it reduces the amount of it by improving the efficiency of the iron chloride. By rationalization of the standard requirement cooperative company, it could cut down the manufacturing cost in the cooperative company, so it could promote the common profits.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.250-251
• /
• 2007

산업용 조사장치로 전자빔은 활용도가 매우 높고, 대부분의 장치는 국내에서 제작이 어려울 뿐만 아니라 외국의존도 높다. 현재 미국, 일본, 러시아, 캐나다 등을 중심으로 약 1500 기의 전자빔 조사 설비가 산업용 및 연구용으로 설치되어 있는데, 이 중 많은 설비가 공동이용 연구시설 또는 상업적인 전자빔 조사서비스 시설로 운영되고 있다. 산업적으로 이용하기 위하여 철원물리기술연구소에 설치될 전자빔 조사 시설을 위한 전자빔 가속기를 개발 중이다. 곡물 살충 및 발아억제, 식품 저장, 위생용품 살균, 의약품 및 의료용구 살균, 전력반도체 생산 등의 분야에 전자빔 조사 설비를 응용할 수 있다. 본 논문에서는 산업용 조사 설비의 전원장치로 사용되는 펄스 모듈레이터의 설계, 제작 및 실험내용을 보이고자 한다.

• Macromolecular Research
• /
• 제16권6호
• /
• pp.532-538
• /
• 2008

Epoxy-based azopolymers were synthesized by the reaction of the diglycidyl ether of bisphenol A (DGEBA) or N,N-diglycidyl aniline (DGA) with disperse orange 3 (DO3) to give poly(DGEBA-co-DO3) or poly(DGA-co-DO3), respectively. Aniline-based azopolymers prepared from poly(DGA-co-An) precursors, synthesized by the reaction of DGA with aniline, were produced by the post-azo coupling reaction with diazonium salts containing various substituents. Holographic gratings were carried out to measure the diffractive efficiencies (DE) for the interference patterns of the $Ar^+$ laser from 50 to $300\;mW/cm^2$ intensity. The shorter repeating unit with higher chromophore density induced deeper surface relief gratings (SRG). Large surface gratings were observed for the aniline-based azopolymers with -COOH substituents, as compared with those for epoxy-based azopolymers. The aniline-based azopolymers with dimerized chromophores and various substituents were also synthesized to observe the effect of chromophore substituents and dimerization on the holography. The dimerized chromophores were more sensitively photoisomerized by the $Ar^+$ laser beam, and demonstrated a larger grating than that with one azo bond.