• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2417-2424
• /
• 2016

Small size and light weight is very important for components used in radar mounted platform such as airborne radar. Recently, the active phased array radar is developed as an array of antennas for thousands of transmit/receive modules to be used as a multi-function radar that can detect and track targets. In this case, the size and weight of the transmit/receive modules are critical factor for developing the radar. In this paper, we developed a compact transmit/receive module using the 10W RF MEMS switch domestically localizing and reduced the circuit area to about 86.5% compared to using a circulator. The developed module satisfies not only electrical requirements but also MIL-STD's environmental specifications. So it can be used in a military device. It can be used at adaptive tunable receivers, reconfigurable smart active antennas and wide band beam electrical steering antennas.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.169-173
• /
• 1997

Most conventional lithography systems have been oriented to fabricate electronic devices. Therefore, it is not so easy to fabricate large aspect ratios of waveguide patterns with those systems. When considering costs and efficiencies, a laser lithography system provides number of benefit in realizing waveguide patterns. However, because the conventional laser lithography system could make only positive tone masks, it is inconvenient in determining the direction of the waveguide. A simple and reliable technique to produce negative tone masks was developed by using the laser beam writing. This technique was not sensitive to environmental situations such as dust, vibration, intensity variation. Making use of the technique a variety of device patterns such as Y-branch, directional coupler, and highly smooth S-shape bend could be successfully fabricated with a good contrast.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.369-377
• /
• 2014

In this paper, to recognize the collision behavior between a submerged floating tunnel(SFT) and underwater navigation vessel(UNV), both structures are modeled and analyzed. The SFT of collision point is modeled tubular section using concrete with steel lining. The other part of SFT is modeled elastic beam elements. Mooring lines are modeled as cable elements with tension. The under water navigation vessel is assumed 1800DT submarine and its total mass at collision is obtained with hydrodynamic added mass. The buoyancy force on SFT is included in initial condition using dynamic relaxation method. The buoyancy ratio (B/W) and the collision speed are considered as the collision conditions. As results, energy dissipation is concentrated on the SFT and that of the UNV is minor. Additionally, the collision behaviors are greatly affected by B/W and the tension of mooring lines. Especially, the collision forces are shown different tendency compare to vessel collision force of current design code.

• Korean Journal of Optics and Photonics
• /
• v.9 no.3
• /
• pp.168-174
• /
• 1998

We have measured nonlinear refractive index and nonlinear absorption coefficient of optical materials by using a far-field phase modulation technique. The phase variation of the probe beam in the nonlinear material is transformed into the spatial phase modulation in the far-field so that the spatial distribution of the optical intensity in conjunction with the computer simulation analysis can give the nonlinear optical constants. We have obtained the nonlinear refractive indices and nonlinear absorption coefficient of $CS_2$ and $BaF_2$ by fitting the experimental values and numerical simulation analysis of far-field measurements. The nonlinear refractive indices of $CS_2$ and $BaF_2$were obtained as $1.2{\times}10^{-11}$ esu and $1.0{\times}10^{-13}$ esu, respectively at 616 nm, and the nonlinear absorption coefficient of BaF$_2$as $5.0{\times}10^{-11}$cm/W at 308nm. These measured values were in good agreement with previous reports.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.108-115
• /
• 2016

In this paper, the array synthesis horn antenna was designed and measured a radiation power after connecting magnetron. The proposed antenna was designed on the basis of the $4{\times}4$ array synthesis horn antenna characteristics. For suppressing a back-lobe, 2 step short-stub structures were attached to synthesis horn aperture upper and lower. The designed antenna has FBR(Front to Back Ratio) of 39.7 dB. HPBW(Half Power Beam Width) of the E-plane and the H-plane are $8.86^{\circ}$ and $7.35^{\circ}$ each in the measurement. For measuring a radiation power of array antenna that use a magnetron, the waveguide adaptor was designed and connected magnetron with horn antenna. Also, microstrip line coupler that replace a dielectric material with an air gap was designed for measuring a high power. As a result, average radiation output power of the $4{\times}4$ array synthesis horn antenna that connect a four magnetrons had a 0.063W.

• Wind and Structures
• /
• v.12 no.6
• /
• pp.479-504
• /
• 2009

Structural health monitoring (SHM) systems have been recently embraced in long span cable-supported bridges, in which buffeting-induced stress monitoring is one of the tasks to ensure the safety of the bridge under strong winds. In line with this task, this paper presents a SHM-oriented finite element model (FEM) for the Tsing Ma suspension bridge in Hong Kong so that stresses/strains in important bridge components can be directly computed and compared with measured ones. A numerical procedure for buffeting induced stress analysis of the bridge based on the established FEM is then presented. Significant improvements of the present procedure are that the effects of the spatial distribution of both buffeting forces and self-excited forces on the bridge deck structure are taken into account and the local structural behaviour linked to strain/stress, which is prone to cause local damage, are estimated directly. The field measurement data including wind, acceleration and stress recorded by the wind and structural health monitoring system (WASHMS) installed on the bridge during Typhoon York are analyzed and compared with the numerical results. The results show that the proposed procedure has advantages over the typical equivalent beam finite element models.

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.22-22
• /
• 1991

광의 병렬처리 능력을 잘 활용한 1$\times$4 매트릭스 스위치의 구조와 전극구조를 설계하고 스위치 특성을 조사하기 위하여 beam propagation method(BPM)를 이용하여 수치계산을 하였다. 기존의 매트릭스 스위치는 대부분의 경우 방향성 결합기를 스위치 element로 이용하여 왔으나 이 결합기는 소자의 길이가 길기 때문에 단일 LinBO3 웨이퍼상에 집적할 수 있는 매트릭스 스위치의 크기가 제한되는 단점이 있다. 본 연구에서는 두 도파로 사이에 세 번째 도파로를 삽입하여 두 도파로를 결합시키는 세 도파로 결합기를 스위치 element로 사용하여 세 개의 스위치 element를 LiNbO3기판위에 직렬로 집적시킨 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치의 특성을 BPM을 사용하여 수치계산할 때 단일 모드 도파로의 유효 굴절을 분포는 n(X) = nm + $\Delta$ncosh-2(2x/w)의 형태로 가정했으며, 사용된 파라미터의 값은 각각 nm=2.1455, $\Delta$n=0.003, W=5$mu extrm{m}$, d=5$\mu\textrm{m}$, λ=1.3$\mu\textrm{m}$ 이고 S-파라메터의 값은 0.95927이므로 단일 모드 도파로가 된다. 계산결과 스위치 element의 결합길이는 3810$\mu\textrm{m}$이며 도파로의 길이가 결합길이와 같을 때 전극에 인가된 전압에 의한 도파로의 굴절을 섭등의 함수로 출력광의 세기를 계산한 결과 스위칭 전압은 14.85volt이고 crosstalk는 -18.9dB였다. 이 스위치 element로 구성된 1$\times$4 매트릭스 스위치는 스위칭 전압을 세 개의 전극에 적절한 조합으로 인가함으로써 한 입력 도파로에 결합된 광이 내개의 출력 도파로중 한 도파로에 스위칭 된다. 한편 수치계산의 결과를 실험적으로 확인하기 위해 스위치 element와 1$\times$4 매트릭스 스위치를 z-cut의 LinbO3 결정에 Ti을 열확산시켜 제작한 소자의 스위칭 특성을 발표할 예정이다.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1297-1300
• /
• 2008

A conventional linear accelerator system requires a flat-topped pulse with less than ${\pm}$ 0.5% ripple to meet the beam energy spread requirements and to improve pulse efficiency of RF systems. A pulse transformer is one of main determinants on the output pulse voltage shape. The pulse transformer was investigated and analyzed with the pulse response characteristics using a simplified equivalent circuit model. The damping factor ${\sigma}$ must be >0.86 to limit the overshoot to less than 0.5% during the flat-top phase. The low leakage inductance and distributed capacitance are often limiting factors to obtain a fast rise time. These parameters are largely controlled by the physical geometry and winding configuration of the transformer. A rise time can be improved by reducing the number of turns, but it produces larger pulse droop and requires a larger core size. By tradeoffs among these parameters, the high-voltage pulse transformer with a pulse width of 10 ${\mu}s$, a rise time of 0.84 ${\mu}s$, and a pulse droop of 2.9% has been designed and fabricated to drive a klystron which has an output voltage of 284 kV, 30-MW peak and 60-kW average RF output power. This paper describes design optimization of a high-voltage pulse transformer for high-power pulsed applications. The experimental results were analyzed and compared with the design. The design and optimal tuning parameter of the system was identified using the model simulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.9-14
• /
• 1996

The dependence of microstructural and optical properties of Ag-In-Sb-Te thin films on annealing heat-treatments was studied. It was found from the present work that the increase of reflectance after annealing heat-treatment is related with phase change of Ag-In-Sb-Te thin film from amorphous state to crystalline phases which involve Sb crystalline phase and AgInTe$_2$ stoichiometric phase. On the other hand, the reflectance is decreased after high temperature annealing (above 450$^{\circ}C$), due to the morphology .mange of film surface. For the purpose of practical application(erasable optical disk), we fabricated quadrilayered Ag-In-Sb-Te alloy disk, and annealed it with continuous laser beam. As result of this laser\ulcorner annealing treatment, we found that the increment of reflectance is 9.3% at 780nm wavelength. It might be considered that Ag-In-Sb-Te alloy optical disk is the big promising candidate for the erasable optical memory medium.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1060-1062
• /
• 1999

Pulsed Nd:YAG laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. And the parallel mesh is added to increase laser output power. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition, we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the parallel mesh and the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 10pps to 110pps by the step of 20pps at 1000V and 1200V, it is found that the laser efficiency decreases but the laser output power increases about 5W at each step.