• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.49-56
• /
• 2005

In this paper, we describe a solution to improve the effects of the transmitter leakage signals on the frequency modulated continuous wave (FMCW) radar with a single antenna configuration. We analyze characteristics of the IF noise caused by insufficient isolation between transmitter and receiver. The magnitude of the intermediate frequency (IF) noise from a front-end can be reduced by matching the LO signal delay time with that of the largest leakage source. Because the IF noise has periodic singularities at nT$_{m}$/2, t=0,1,2$\cdots$, we find that spectrum of the IF noise due to the leakage signals is very similar to that of the VCO moduation signal except low frequency elements in the vicinity of DC. Based on the studies, we fabricated a W-band homodyne FMCW radar sensor and verified the proposed solution. The results are applicable to design of the homodyne FMCW radar with a single antenna configuration.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.12
• /
• pp.155-160
• /
• 2003

Owing to the advances in ADC and DSP technologies, signals in If band, which once had to be processed in analog technology, can new be digitally processed. This is referred to as "Digital IF" or "Digital Radio", which is a preliminary stage of SDR. Applying the digital radio technology to a multi-carrier receiver design, a processing gain is generated through an over-sampling of input data. In the digital receiver, decimation is performed for reducing the computational complexity CIC and half band filter is used together with the decimation as an anti-alising filter. The CIC filter, however, should introduce the roll-off phenomenon in the passband, which causes the receiving performance to be considerably degraded due to the distorted Passband flatness of receiving filter. In this paper, we designed a CIC roll-off compensation filter for W-CDMA digital receiver. The performance of the proposed compensation filter is confirmed through computer simulations in such a way that the BER is minimized by compensating the roll-off characteristics.off characteristics.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.11
• /
• pp.1311-1316
• /
• 2014

To be used in a transmitter of a satellite transponder of this paper, X band 25W power amplifier module, a part constituting of high-power amplifier is transmitted to the equipment for transmitting to geostationary communications satellites(36,000Km distance). PAM consisted a total of four power amplifier module has a high output characteristic of the high-output amplifier is used in the ground station. Used in conjunction with the structured type power amplifier module is composed of Serial Combining Structure. This PAM(Power Amplifier Module) configured by combining the circuit with the power amplifier, 10 MMIC chips and the Al2O3 thin film substrate using a Hybrid Technique of power amplifier module, was implemented at X band PAM(Power Amplifier Module) of 25W grade.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.4
• /
• pp.599-604
• /
• 2021

In the information age, internet was developed from the wired access to the wireless Internet access. When a surge in demand for wireless Internet access, efficiency and performance of 2.4 and 5GHz band which leads to saturation of the communication was significantly fall. In this paper, we studied the design and fabrication of slot patch antenna to be used in wireless communication systems operating at around 10GHz band. To obtain optimal antenna parameters such as patch size, inter patch space, sL, sW, feed L, feed w, slot patch antenna was simulated by HFSS(High Frequency Structure Simulator). From these parameters, slot and patch antenna is fabricated using FR-4 substrate of dielectric constant 4.4. The characteristics of fabricated antenna were analyzed by network analyzer. The fabricated slot patch antenna showed a center frequency as 10.23GHz, the minimum return loss as -32dB, and -10dB bandwidth as 420MHz respectively.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.121-130
• /
• 2005

In this paper, we designed and fabricated the VHF wireless transmitter for air traffic control. Fundamental performance of the investigated wireless transmitter is designed and fabricated to satisfy existing commercial wireless transmitter specification for air traffic control. 25 W and 50 W of output power can be generated by changing the power amplification part only. It is based on transmitting voice communication using AM modulation. Investigated wireless transmitter for air traffic control consists of four module parts: power supply, control, low power transmission and power amplification. We designed 1W transmitter to operate without power amplification part. It can be used properly in a basic component of CNS/ATM.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.76-79
• /
• 2016

This paper describes the successful development and the performance of X-band 50 W pulsed power amplifier using a 50 W GaN-on-SiC high electron mobility transistor. The GaN HEMT with a gate length of $0.25{\mu}m$ and a total gate width of 12 mm were fabricated. The X-band pulsed power amplifier exhibited an output power of 50 W with a power gain of 6 dB in a frequency range of 9.2~9.5 GHz. It also shows a maximum output power density of 4.16 W/mm. This 50 W GaN HEMT and X-band 50 W pulsed power amplifier are suitable for the radar systems and related applications in X-band.

• The Magazine of the IEIE
• /
• v.25 no.5
• /
• pp.61-70
• /
• 1998

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.4
• /
• pp.290-298
• /
• 2018

Herein, an S-band internally-matched power amplifier that shows a power capability of 300 W in a Long Term Evolution(LTE) band 7 is designed and fabricated using a CGHV40320D GaN HEMT from Wolfspeed. Based on the nonlinear model, the optimum source and load impedance are extracted from the source-pull and load-pull simulations at the fundamental and harmonic frequencies, and the harmonic impedance tuning circuits are implemented inside a ceramic package. The internally matched power amplifier, which is fabricated using a thin-film substrate with a high relative permittivity of 40 and an RF35TC PCB substrate, is measured at the pulsed condition with a pulse period of 1 ms and a duty cycle of 10%. The measured results show a maximum output power of 257~323 W, a drain efficiency of 64~71%, and a power gain of 11.5~14.0 dB at 2.62~2.69 GHz. The LTE-based measurement shows a drain efficiency of 42~49% and an ACLR of less than -30 dBc(excluding 2.62 GHz) at an average power of 79 W.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1133-1138
• /
• 2010

We have developed an imaging radiometer system at W-band. The system consists of lens, reflector, 30-ch receiver array, scanner, and signal processor. One receiver consists of a dielectric rod antenna, a balun, LNA(low noise amplifier) and a detector. The system configuration requirements are described. Finally, we represent radiometer images to obtain through clouds, smoke, dust, and other obstructions which render visible and IR systems ineffective.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.4 s.346
• /
• pp.67-74
• /
• 2006

We present the design of a radiometer in W-band which operates simultaneously with a single antenna configured FMCW radar. We choose a total power radiometer(TPR) which shares an antenna and a front-end with the radar for miniaturizing the system. We separate the radiometer signal from the radar signal using a diplexer in IF band. Because the radiometer has an unwanted transmitter section due to the common use of the MMW front-end with the radar, some additional noise signals caused by the transmitter degrade the sensitivity of the radiometer system. To compensate the degradation of sensitivity, we use matching circuits and a diode detector configured as the voltage doubler. Through some experiments, we have verified that the designed radiometer system has good performances in detecting metal targets tying at several hundred meters.