• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.546-552
• /
• 2001

The heat transfer and flow measurements on a pedestal encountered in chip cooling. A uniform wall temperature boundary condition at the plate surface and on a pedestal was created using shroud method. Liquid crystal was used to measure the plate surface temperature. The jet Reynolds number (Re) ranges from 11,000 to 50,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, and the dimensionless pedestal diameter-to-height (H/D) from 0 to 1.0. The results show that the Nusselt number distributions at the near the pedestal exhibit secondary maxima at $r/d{\cong}1.0\;and\;1.5$. The formation of the secondary maxima is attributed to an create in the vortex by the pedestal.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.754-759
• /
• 2001

This paper presents unsteady computational investigations and wind tunnel tests on the flow field around a square cylinder with a gap between the body and the ground plane. Two-dimensional unsteady, incompressible Navier-Stokes codes are developed for the computation of the viscous turbulent flows. By computing the flow around a square cylinder without ground effect, three two-equation turbulence models are evaluated and the developed code is validated. The results show a good agreement with experimental values and other computational results. Critical gap height at which the formation of Karman vortex streets is interrupted, is demonstrated and another transition regime is pointed out

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.196-201
• /
• 2004

Aerodynamic characteristics of three-dimensional wings in ground effect for Aero-levitation Electric Vehicle(AEV) are numerically investigated for various ground clearances and wing spans at the Reynolds number of $2\times10^6$. Numerical results show that a sizeable three-dimensional flow separation occurs with formation of an arch vortex at the junction of main and vertical wings, and that this is conjectured a primary cause for the high lift-to-drag(L/D) reduction rate of the main wing, when the wing span is decreased. Improvements on L/D ratios of the wings with small spans are pursued by breaking the coherence of superimposed adverse pressure gradients at the wing junction.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.05a
• /
• pp.91-98
• /
• 2000

The three-dimensional unsteady compressible Full Navier-Stokes equation solver with sliding multi-block method has been applied to analyze three dimensional characteristics of the flow field and compression wave around the high speed train which Is entering into a tunnel. The numerical scheme of AF + ADI was used to efficiently solve Navier-Stokes equations in the curvilinear coordinate system. The vortex formation around the nose region was found and the generation of compression wave due to the blockage effects was observed ahead of the train in the form of plane wave. The three dimensional characteristics of the flow field compared to the analytic results were discussed in detail. The variation of pressure of tunnel wall surface and velocity profile of the train are identified as the train enters into a tunnel. The changes in aerodynamic forces and streamlines of each specific sections are also discussed and presented.

• Journal of computational fluids engineering
• /
• v.5 no.3
• /
• pp.23-31
• /
• 2000

The three-dimensional unsteady compressible Full Navier-Stokes equation solver with sliding multi-block method has been applied to analyze three dimensional characteristics of the viscous flow field and compression wave around the high speed train which is entering into a tunnel. The numerical scheme of AF + ADI was used to efficiently solve Navier-Stokes equations in the curvilinear coordinate system. The vortex formation owing to the viscous interaction around the train was found and the generation of compression wave due to the blockage effects was observed ahead of the train in the form of plane wave. The three dimensional characteristics of the flow field compared to the analytic results were discussed in detail. The variation of pressure of tunnel wall surface and velocity profile of the train are identified as the train enters into a tunnel. The changes in aerodynamic forces and streamlines of each specific sections are also discussed.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2014.05a
• /
• pp.143-143
• /
• 2014

• Journal of computational fluids engineering
• /
• v.11 no.4 s.35
• /
• pp.9-13
• /
• 2006

In the present study, a numerical analysis of transient mixer flow is performed considering free surface formation. The flow patterns and free surface shape in a mixers formed by flat paddle and pitched paddle impellers are predicted. In a flat paddle mixer, two flow circulation regions are formed due to strong radial flow, whereas one large circulation is formed in a pitched paddle mixer due to axial downward flow. These differences affect the free surface evolution and shape. It is seen from the results that a flat paddle mixer gives deeper free surface at center region than a pitched paddle mixer. The free surface of 8-blades-flat-paddle mixer is also simulated to compare with the available experimental and simulation results. The present computational results agree reasonably well with the experimental data.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.1
• /
• pp.101-113
• /
• 1994

This research has presented and experimental investigation on the characteristics of turbulent wake past a rectanular cylinder, according to various width/height ratio such as B/H=2.0, 2.79, 3.0, and 4.0 in a uniform shear flow. In order to perform this study, a special shear flow generator which produces the uniform shear flow has been designed and manufactured. It is found that the characteristics of the wake in a uniform shear flow are quite different from those of a uniform flow and vary with shear rate. And also, the formation of regular vortex structure is concerned with shear rate.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.5-11
• /
• 2010

분사연료의 혼합기형성과정 최적화를 통한 연소제어 기술은 디젤기관의 기관운전 및 배기특성을 향상시키기 위하여 매우 중요하다. 또한 분무의 혼합기형성 최적화를 위해서는 분사된 연료와 주위기체와의 혼합과정에 영향을 미치는 분무내부의 유동특성에 대한 연구는 필수 불가결하다. 따라서 본 연구에서는 고온 고압의 증발장에서 분무의 액상 거동에 주목하고, 그 거동특성을 통하여 증발디젤분무의 혼합기형성을 해석한다. 비정상 증발분무의 중심축에 레이저 시트광을 입사한 후, 액상분무 액적의 Mie 산란광에 의한 2차원 화상을 획득하여 증발분무 액상의 속도분포 및 와도(vorticity) 등을 구하였다. 분무의 속도분포 및 와도는 2차원 화상에 PIV법을 적용하여 계산하였다. 그림 1에 본 연구에서 구한 속도분포의 일례를 보인다. 본 연구의 결과로 상변화를 동반하는 비정상 증발장에서 구한 분무액상의 거동 특성은 상변화가 일어나지 않는 비증발장에 있어서의 분무거동특성과 유사함을 확인하였다.

• Wind and Structures
• /
• v.19 no.1
• /
• pp.59-73
• /
• 2014

This paper presents the results of wind tunnel studies and numerical studies on a '+' plan shaped tall building. The experiment was carried out in an open circuit wind tunnel on a 1:300 scale rigid model. The mean wind pressure coefficients on all the surfaces were studied for wind incidence angle of $0^{\circ}$ and $45^{\circ}$. Certain faces were subjected to peculiar pressure distribution due to irregular formation of eddies caused by the separation of wind flow. Moreover, commercial CFD packages of ANSYS were used to demonstrate the flow pattern around the model and pressure distribution on various faces. k-${\varepsilon}$ and SST viscosity models were used for numerical study to simulate the wind flow. Although there are some differences on certain wall faces, the numerical result is having a good agreement with the experimental results for both wind incidence angle.