• Korea-Australia Rheology Journal
• /
• 제13권1호
• /
• pp.47-54
• /
• 2001

Prediction of the maximum packing volume fraction with non-spherical particles has been one of the important problems in powder technology. The sphericity of fly ash particles depending on the particle diameter was measured by means of a CCD image processing instrument. An algorithm to predict the maximum packing volume fraction with non-spherical particles is proposed. The maximum packing volume fraction is used to predict the slurry viscosity under well dispersed conditions. For this purpose, Simha's cell model is applied for concentrated slurry with wide particle size distribution. Also, Usui's model developed for aggregative slurries is applied to predict the non-Newtonian viscosity of dense fly ash - water slurry. It is certified that the maximum packing volume fraction for non-spherical particles can be successfully used to predict slurry viscosity. The pressure drop in a pipe flow is predicted by using the non-Newtonian viscosity of dense fly ash-water slurry obtained by the present model. The predicted relationship between pressure drop and flow rate results in a good agreement with the experimented data obtained for a test rig with 50 mm inner diameter tube. Base on the design procedure proposed in this study, a feasibility study of fly ash hydraulic transportation system from a coal-fired power station to a controlled deposit site is carried out to give a future prospect of inexpensive fly ash transportation technology.

• Nuclear Engineering and Technology
• /
• 제38권4호
• /
• pp.343-352
• /
• 2006

Convenient analytical tools for evaluation of the aperiodic and the fluctuating instabilities of the passive residual heat removal system (PRHRS) of an integral reactor are developed and results are discussed from the viewpoint of the system design. First, a static model for the aperiodic instability using the system hydraulic loss relation and the downcomer feedwater heating equations is developed. The calculated hydraulic relation between the pressure drop and the feedwater flow rate shows that several static states can exist with various numbers of water-mode feedwater module pipes. It is shown that the most probable state can exist by basic physical reasoning, that there is no flow rate through the steam-mode feedwater module pipes. Second, a dynamic model for the fluctuating instability due to steam generation retardation in the steam generator and the dynamic interaction of two compressible volumes, that is, the steam volume of the main steam pipe lines and the gas volume of the compensating tank is formulated and the D-decomposition method is applied after linearization of the governing equations. The results show that the PRHRS becomes stabilized with a smaller volume compensating tank, a larger volume steam space and higher hydraulic resistance of the path $a_{ct}$. Increasing the operating steam pressure has a stabilizing effect. The analytical model and the results obtained from this study will be utilized for PRHRS performance improvement.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.181-183
• /
• 2002

The accurate permeability for preform is critical to model and design the impregnation of fluid resin in the composite manufacturing process. In this study, the in-plane and transverse permeability for a woven fabric are predicted numerically through the coupled flow model which combines microscopic with macroscopic flow. The microscopic and macroscopic flow which are flows within the micro-unit and macro-unit cell, respectively, are calculated by using 3-D CVFEM(control volume finite element method). To avoid checker-board pressure field and improve the efficiency on numerical computation, A new interpolation function for velocity is proposed on the basis of analytic solutions. The permeability of plain woven fabric is measured through unidirectional flow experiment and compared with the permeability calculated numerically. Based on the good agreement of the results, the relationships between the permeability and the structures of preform such as the fiber volume fraction and stacking effect can be understood. The reverse and the simple stacking are taken in account. Unlike past literatures, this study is based on more realistic unit cell and the improved prediction of permeability can be achieved. It is observed that in-plane flow is more dominant than transverse flow in the real flow through preform and the stacking effect of multi-layered preform is negligible. Consequently, the proposed coupled flow model can be applied to modeling of real composite materials processing.

• 한국유체기계학회 논문집
• /
• 제18권4호
• /
• pp.49-55
• /
• 2015

The pumped storage plant operates with quick change of the discharge as well as quick changes between pump mode and turbine mode. This study focuses on the cavitation analysis of a pump-turbine model because in turbo-machinery, cavitation can reduce the performance and shorten service life. The pump-turbine model system consists of 7 blades, 20 stay vanes (including tongue) and 20 guide vanes. This study adopts the Rayleigh-Plesset model as a cavitation model, which illustrates cavitation by using the air volume fraction method. The pump mode and turbine mode at the operating condition of partial loading, normal and excessive loading are analyzed to investigate the cavitation performance of the pump-turbine. It was observed that this pump-turbine design showed very good cavitation characteristics with no cavitation bubbles in all operating conditions. Overall value of air volume fraction of both mode at different operating condition are lower than 1, which confirms low possibility of cavitation occurrence at current situation.

• Computers and Concrete
• /
• 제7권5호
• /
• pp.421-435
• /
• 2010

This paper utilizes the modified Davis model and the mode coupling theory, as parts of the electrolyte solution theory, to investigate the diffusivity of the ion in concrete. Firstly, a computational model of the ion diffusion coefficient, which is associated with ion species, pore solution concentration, concrete mix parameters including water-cement ratio and cement volume fraction, and microstructure parameters such as the porosity and tortuosity, is proposed in the saturated concrete. Secondly, the experiments, on which the chloride diffusion coefficient is measured by the rapid chloride penetration test, have been carried out to investigate the validity of the proposed model. The results indicate that the chloride diffusion coefficient obtained by the proposed model is in agreement with the experimental result. Finally, numerical simulation has been completed to investigate the effects of the porosity, tortuosity, water-cement ratio, cement volume fraction and ion concentration in the pore solution on the ion diffusion coefficients. The results show that the ion diffusion coefficient in concrete increases with the porosity, water-cement ratio and cement volume fraction, while we see a decrease with the increasing of tortuosity. Meanwhile, the ion concentration produces more obvious effects on the diffusivity itself, but has almost no effects on the other ions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• 대한기계학회논문집B
• /
• 제36권7호
• /
• pp.721-730
• /
• 2012

본 연구에서는 벽면부착에 의해 야기되는 다상유동에 대한 수치적 연구를 제시한다. 먼저 다상유동 해석을 위해 표면장력에 대한 CSF(Continuum Surface Force) 모델 및 벽면부착 경계조건 모델을 비정렬격자계에 적합하도록 수치해석방법을 정립시키고, Myong(2009)이 개발한 비정렬격자계와 VOF 방법으로 체적포착법(volume capturing method)을 사용한 수치해석방법(코드)에 삽입하였다. 또한 본 수치해석방법을 사용하여 중력을 포함하여 어떤 외력도 존재하지 않고 오직 벽면부착에 의해 야기되는 유동현상인 원통형 탱크의 바닥에 위치한 얕은 물풀(water pool)에 대해 물이 벽면을 적시는 경우와 적시지 않는 경우에 대해 수치해석 하였다. 연구결과, 본 수치해석방법은 벽면부착에 의해 야기되는 다상유동 문제에 대한 유용성이 입증되었다.

• 한국환경과학회지
• /
• 제31권11호
• /
• pp.941-950
• /
• 2022

This study was conducted to provide data and stem information to establish a local volume table of Cryptomeria japonica in Jeju Island. Stem analysis was performed on 26 trees by selecting two average trees from each site of the 13 plots of C. japonica stands in 2021 and 2022. During the analysis stage, one outlier tree was rejected, and a total of 260 observations of the specific stem height of 25 trees were used. Of the seven major taper equation models applied for parameter estimation and statistical verification, the Muhairwe 1999 model was found to be the best fit and selected as the optimal model. Stem shape-related estimates were acquired through the selected model, and sectional measurements according to the Smalian formula applied at an interval of 10 cm from the height of the stem were used to develop a volume table. A paired t-test comparison between the C. japonica volume obtained from the present study and those selected from the current yield table by NIFoS(2020), revealed significant differences (p<0.05), highlighting the necessity of a local volume table for C. japonica in Jeju Island.

• 산업공학
• /
• 제24권3호
• /
• pp.241-247
• /
• 2011

This paper develops a mathematical model which searches an optimum lot size of a press line, and applies this model to the scheduling of the press line. This mathematical model is not a widely studied cost model but a model which considers the utilization of the press line under a lean production system. In this paper, the optimum lot size is a minimum lot size which does not exceed the total work time of the press line. A production volume and the priority of the production in the press line are adjusted using this optimum lot size. A mathematical model developed in this paper will allow determining the optimum lot size easily in case of variable production environments such as an introduction of a new product and a fluctuation of production volume of each item. Therefore, our model will make a better scheduling of the press line and will enhance the utilization of it.

• 한국CDE학회논문집
• /
• 제12권2호
• /
• pp.101-108
• /
• 2007

As 3D solid modeling has been widely used in designing products, solid models of the products are directly used in various applications such as engineering analysis and process planing. However, the fully-detailed solid models may not be necessary in some application. For example, it is often more efficient to use simplified model of part of engineering analysis. Generation of mesh for the complex original model requires a quite amount of time, and the consequence of finite element analysis may not be desirable due to small and detailed geometry in the model. In this paper, a method to simplify solid models of machined part is presented. This method decomposes the delta volume of machined part, and uses the decomposed volumes to simplify the solid model. Since this method directly recognizes the features to be removed from the final model, it is independent of not only design features of specific CAD system, but also designer's design practice of design sequences.