• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.490-492
• /
• 2010

Center-tapped termination을 가진 stub series-termination logic (SSTL) 채널을 지원하기 위한 전압모드 송신단을 제안한다. 제안하는 송신단은 진단 모드를 지원하고 신호보전성을 향상시키기 위해 출력레벨 조절수단을 가지며, 가변 병렬 터미네이션을 사용하여 swing level을 조절하는 동안 송신단의 출력 저항을 일정하게 유지시켜준다. 또한 제안하는 송신단의 off-chip 저항은 기생 캐패시터, 인덕터에 의한 termination의 임피던스 부정합을 줄여준다. 제안된 송신단을 검증하기 위해서 $50{\Omega}$의 출력저항을 유지하면서 8-레벨의 출력을 제공하는 전압모드 송신단을 1.5V의 70nm 1-poly 3-metal DRAM공정을 이용하여 구현하였다. 수신단 termination이 존재하지 않는 SSTL 채널에서 제안하는출력레벨 조절이 가능한 송신단을 이용함으로 1.6-Gb/s에서 54%의 jitter 감소가 측정되었다.

• 한국전자통신학회논문지
• /
• 제16권1호
• /
• pp.69-74
• /
• 2021

본 논문은 저항과 캐패시터로 구성된 필터를 사용한 저전력 전압 제어 발진기를 소개하고 있다. 제안하는 전압 제어 발진기는 5단의 전류모드 버퍼로 구성되어 있으며, 각 버퍼 셀마다 저항-캐패시터 필터가 입력단과 출력단 사이에 연결되어 있다. 필터는 버퍼 셀 회로에 영점을 추가하게 되며, 영점은 회로 발진 조건을 고주파 대역으로 이동시킴으로써 낮은 전력 소모에도 높은 출력 주파수를 낼 수 있게 한다. 제안하는 회로는 0.18 ㎛ CMOS 공정으로 설계되었다. 소모 전력은 2.7 GHz 에서 9.83 mW를 소모한다. 기존 회로와 전력 효율을 비교했을 때, 기존 회로는 4.79 pJ/Hz이고 제안하는 회로는 3.64 pJ/Hz로 기존 회로 대비 전력 소모량을 24 % 감소시켰다.

• Smart Structures and Systems
• /
• 제18권3호
• /
• pp.449-470
• /
• 2016

Energy harvesting is an emerging technique that extracts energy from surrounding environments to power low-power devices. For example, it can potentially provide sustainable energy for wireless sensing networks (WSNs) or structural control systems in civil engineering applications. This paper presents a comprehensive study on harvesting energy from earthquake-induced structural vibrations, which is typically of low frequency, to power WSNs. A macroscale pendulum-type electromagnetic harvester (MPEH) is proposed, analyzed and experimentally validated. The presented predictive model describes output power dependence with mass, efficiency and the power spectral density of base acceleration, providing a simple tool to estimate harvested energy. A series of shaking table tests in which a single-storey steel frame model equipped with a MPEH has been carried out under earthquake excitations. Three types of energy harvesting circuits, namely, a resistor circuit, a standard energy harvesting circuit (SEHC) and a voltage-mode controlled buck-boost converter were used for comparative study. In ideal cases, i.e., resistor circuit cases, the maximum electric energy of 8.72 J was harvested with the efficiency of 35.3%. In practical cases, the maximum electric energy of 4.67 J was extracted via the buck-boost converter under the same conditions. The predictive model on output power and harvested energy has been validated by the test data.

• 대한전자공학회논문지SD
• /
• 제46권4호
• /
• pp.72-78
• /
• 2009

본 논문에서는 $0.13{\mu}m$ CMOS 공정의 이득(Kvco) 제어 지연 단을 이용한 위상동기루프에 사용되는 저 위상잡음 CMOS 링 전압제어발진기를 설계 및 제작한다. 제안하는 지연 단은 출력 단자를 잇는 MOSFET을 이용한 능동저항으로 전압제어발진기의 이득을 감소시킴으로써 위상잡음을 개선한다. 그리고 캐스코드 전류원, 정귀환 래치와 대칭부하 등을 이용한다. 제안한 전압제어 발진기의 위상잡음 측정결과는 1.9GHz가 동작 할 때, 1MHz 오프셋에서 -119dBc/Hz이다. 또한 전압제어발진기의 이득과 전력소모는 각각 440MHz/V와 9mW이다.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.950-955
• /
• 2013

This paper proposes a new low-cost current detection method to implement vector-controlled inverter of 3-phase induction motor or permanent-magnet synchronous motor using 2 shunt resistors instead of expensive Hall current sensors. The proposed method can detect perfect phase currents without current-immeasurable area in all operating conditions of motor. This method uses 2 shunt resistors in Hall current sensor positions conventionally used to detect phase currents. Therefore, it requires accurate analog differential amplifiers to detect voltages across shunt resistors at high electric potential to ground. We show the good solutions which are implemented by voltage-divider resistors networks and the instrumentation amplifiers using several Op Amps at cheap price. Computer simulations and experiments were performed to confirm the effectiveness of proposed method. These results show that proposed method can perfectly detect phase currents without current-immeasurable area in all operating conditions of motor.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2678-2689
• /
• 1995

In this study, a new hot-wire anemometer which has greater sensitivity than that of a constant temperature anemometer (CTA) was proposed. In contrast to CTA, the wire working resistance of the new anemometer increases with flow velocity, that is, the operating mode of the wire becomes variable temperature. The variable temperature anemometer(VTA) was made by substituting a voltage controlled variable resistor such as photoconductive cell or transistor for one of the resistors in the bridge. By positively feeding back the bridge top signal to the input side of these electronic components, the wire overheat ratio could be increased with velocity automatically. Static response analyses of the VTA, constant voltage anemometer (CVA) and CTA were made in detail and calibration experiments were performed to validate the proposed operating principle. The wire operating resistance of the CVA decreases with velocity and this leads to lower sensitivity than that of a CTA. But the sensitivity of the newly proposed VTA is superior to that of a CTA, since the wire overheat ratio increases with velocity. Consequently, it is found that the major factor that is responsible for large sensitivity of a VTA is not the working resistance itself but the change of the wire working resistance with velocity.

• 한국전자통신학회논문지
• /
• 제14권1호
• /
• pp.81-86
• /
• 2019

본 논문은 복수개의 스위칭모드 전원장치를 병렬 결선을 통하여 부하에 보다 큰 전력을 공급가능하게 하는 시스템 설계에 관한 것이다. 이를 위해 정전압조정기의 출력단에 션트저항을 직렬로 배치하고 아두이노를 이용하여 출력단 전압을 감지하고 제어하도록 하였다. 본 논문에서는 실험을 위해 두 개의 정전압조정기를 이용하였으나 그 이상의 보드에 대해서도 일반화가 가능할 것이다. 이와 같은 방식으로 제어되는 시스템을 통해 두 개의 시스템이 부하에 전달되는 전류의 합이 각각의 보드에서 나온 전류의 96%가 부하에 전달되는 것을 확인하였다. 효율의 경우 단위 보드에서의 효율은 92.4% 정도가 나왔으며 병렬결선 시에는 90% 정도가 나왔다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.32-35
• /
• 2003

Nonlinear parameterization of OLED device from measurements of bias dependence of impedance spectra and parameter extraction using Levenberg-Marquardt complex nonlinear least square regression algorithm based on resistor-capacitor equivalent circuit model enables computer simulation of OLED power driving characteristics in forms of square-wave or sinusoidal output signal at arbitrary conditions. We introduce developed OLED power driving simulation software and discuss transient responses in voltage-or current-controlled operations as well as nonlinear characteristics of OLED, by presenting both the simulation and experimental results. This OLED simulation technique using impedance spectroscopy is extremely useful in predicting performance of the nonlinear device, especially in time-domain analysis of device operation.

• 전기학회논문지
• /
• 제59권5호
• /
• pp.1005-1009
• /
• 2010

This paper presents a digitally-controlled filter calibration technique for biquad RC filter using self oscillation. The biquad RC filter is converted to a fully-differential ring oscillator by changing its resistor connections, where the oscillation frequency reflects the cut-off frequency. The proposed calibration circuit measures the oscillation frequency by counting with a fixed higher-frequency clock and then tunes it to a desired frequency with a digital frequency-locked loop including a PI controller. Because the proposed circuit directly measures the cut-off frequency of the filter itself and calibrates it with the small area digital circuits, the area and the power consumption are much small compared with conventional works. When it is implemented in a 65nm CMOS process, the calibration circuit except the filter consumes the area of 80um X 50um and power consumption is 443uA at 1.2 V supply voltage.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제5C권4호
• /
• pp.152-154
• /
• 2005

We demonstrate a simple $CO_2$ laser by controlling firing angle of a TRIAC switch in ac power line. The power supply for our laser system switches the voltage of the AC power line (60Hz) directly. The power supply does not need elements such as a rectifier bridge, energy-storage capacitors, or a current-limiting resistor in the discharge circuit. In order to control the laser output power, the pulse repetition rate is adjusted up to 60Hz and the firing angle of TRIAC gate is varied from $45^{circ}$ to $135^{circ}$. A ZCS(Zero Crossing Switch) circuit and a PIC one-chip microprocessor are used to control the gate signal of the TRIAC precisely. The maximum laser output of 40W is obtained at a total pressure of 18 Torr, a pulse repetition rate of 60Hz, and a TRAIC gate firing angle of $90^{circ}$.