• 전자공학회논문지A
• /
• 제32A권3호
• /
• pp.124-133
• /
• 1995

A theoretical self-consistent thermoelectric model has been developed for optimal thermal design in the self-signal processing infraed detectors. The model is achived by employing the coupled thermoelectric equation which allows which allows the simultaneous investigation of the termal and electrical aspects of device behavior. The thermal limitation of detectivity and responsivity are determined by the enegy gap, carrier concentration, lifetime, and mobility as a function of the temperature. The calculated results indicate that the detectivity is decreased at bias fields above about 50 V/cm, because the performence is limiting by temperature when the bias voltage reached the level associated with Joule heating. It has been also found that the improvement in the mid-band modulation transfer function(MTF) may be restricted by increasing the bias fields. Further, the important paramerers in the thermal optimization of SPIR detector, such as temperature in the device, ambipolar velocity, element thickness and length, are also considered. The analytical study provides a mathematical basis for optimal design of such a photoconductive IR detector and the agreement between the experimental and theoretical results are seen to be good.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.183-185
• /
• 2002

This paper proposes the test method for the testing of a RLC parallel circuit on the electronic circuit board. This method utilizes a guarding circuit and a phase detection circuit. The guarding circuit separates electrically the tested device or circuit from printed circuit board. Phase detector estimates the phase difference from two signals, voltage and current. This method computes R. L and C value from phase difference($\theta$) and impedance value(Z) obtained by enforcing two other frequence stimulus under the guarding state.

• 한국산업융합학회 논문집
• /
• 제19권2호
• /
• pp.95-100
• /
• 2016

This study proposes the temperature compensation algorithm using thermopile detector for non-dispersive infrared Nitrogen gas sensor. From the output voltage of thermistor that is attached onto the infrared detector, the ambient temperature was extracted. The effects of temperatures on the properties of sensor module characteristics of narrow bandpass filter, optical cavity and infrared lamp, and air mixing gas have been introduced in order to implement the temperature compensation algorithm.

• 한국통신학회논문지
• /
• 제22권7호
• /
• pp.1566-1573
• /
• 1997

In this paper, we propose a favorite color correction algorithm for color enhancement in color application system which represent preferred colors for viewer's demands. The proposed algorithm corrects skin color which is widely used as a reference color for color control of color application system, blue color which is directly related to tri-stimulus values, and green color which has higher visual sensitivity. In the proposed algorithm, the vaiation range of phase detector output voltage was minimized for the favorite color saturation changes, thus the favorite from the burst signal for the phase detector characteristic, thus the favorite color was easilty detected from the other color without overlapping of correctionranges.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권10호
• /
• pp.449-452
• /
• 2005

We fabricated an electrochemical detector (ECD) to catalyze redox reaction efficiently by electrodepositing Prussian blue (PB) on the indium tin oxide (ITO) electrode. Capillary electrophoresis (CE) and amperometric method were used. We investigated the PB surface properties by topography from atomic force microscopy (AFM). Also PB film thickness calibration with respect to deposition time and voltage was used to get better PB surFace. The PB thin film of dense and smooth surface could catalyze redox reaction efficiently. Comparing with CE-ECD microchip using bare-lTO electrode, proposed CE-ECD microchip using PB deposited electrode has shown better sensitivity by determining the detected peak current from the electropherograms while the concentration of tested analyzes was maintained the same. It is verified that detection limit can be lowered for 0.01 mM of dopamine and catechol respectively.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.973-979
• /
• 1995

The input equivalent noise charge (ENC) of hydrogenated amorphous silicon radiation detector diodes was measured and analyzed. The noise sources of amorphous silicon diodes were analyzed into three sources; shot noise, flicker noise and thermal noise from the contact resistance. By comparing the measured ENC with the calculated signal charge in uniform generation case, the signal-to-noise ratio (S/N) for the sample diodes is estimated as a function of the detector bias and the shaping time of Gaussian pulse shaper. The maximum S/N occurred at the bias level just above the full depletion voltage for shaping time of 2∼3 ${\mu}$sec. The developed method is useful in optimum design or amorphous silicon p-i-n diodes for charged particulate radiation spectroscopy.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.465-466
• /
• 2006

In this paper, novel analog duty cycle corrector (DCC) with a digital duty error detector is proposed. The digital duty error detector measures the duty error of the clock and converts it into a digital code. This digital code is then used to accurately correct the duty ratio by adaptively steering the charge-pump current. The proposed duty cycle corrector was implemented using an 80nm DRAM process with 1.8V supply voltage. The simulation result shows that the proposed duty cycle corrector improves the settling time up to $70{\sim}80%$ at 500MHz clock frequency for the same duty correction accuracy as the conventional analog DCC.

• 한국전자파학회논문지
• /
• 제11권5호
• /
• pp.822-829
• /
• 2000

본 논문에서는 무선광열에서 잡음광의 영향을 소거하는 동시에, 신호광원의 미세한 정렬변동에 의하여 빔의 진행방향이 이동할 경우 발생하는 출력전압의 변동을 막기 위한 자동정렬형 차동검출기를 개발하여 소개한다. 이 구조에서는 신호빔과 수직한 포토다이오드 배열을 사용하여 빔의 중심위치를 감지하고, x축과 y축에 해당하는 모토를 구동한다. 포토다이오드배열은 자신의 위치가 항상 신호빔의 중심에 오도록 자동적으로 조절하는 동시에 차동검출방식으로 잡음광의 영향을 소거하는 기능을 가지므로 무선광연결에서 매우 유용하게 쓸수 있다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권4호
• /
• pp.190-196
• /
• 2001

We measured 3-dimensional images of the light emitted from plasma display panel(PDP) by using newly proposed scanned point detecting method(SPDM). The SPDM has the point detector with pinhole. The light emitted from PDP cell at the in-focus position can pass through the pinhole and be collected by detector. On the contrary, the light emitted from PDP cell at the out-of-focus positions is focused on the front of or the behind of the pinhole. We could analyze the characteristic of 3-dimensional light emission distribution by SPDM. From 3-dimensional measurement of 828[nm], the efficient design of PDP cell, the importance of opening ration, and the relations between BUS electrode position and discharge intensity are obtained. Also, the relationship between discharge characteristics and sustain electrode structures in AC-PDP are studied by measuring luminance, current, and discharge voltage.

• 한국정밀공학회지
• /
• 제11권6호
• /
• pp.50-56
• /
• 1994

A DC generator control system was designed to control the torque of a rotating shaft precisely. The control system is composed of a strain gage type torque cell, a torque cell amplifier, a computer, a D/A converter, a error detector, a DC voltage amplifier and a resistor. The response test under unit step input and the dynamic stability test for the designed control system were carried out. It was confirmed that the settling time from the response test is about 4 s and the error from the dynamic stability test is less than 0.06% of rated output of torque cell. The designed control system may be used to control a DC generator which may be used to apply torque to a rotating shaft.