• Land and Housing Review
• /
• v.11 no.1
• /
• pp.87-94
• /
• 2020

To implement the planning of zero-energy buildings, their energy performance must be improved, and renewable energy applications must also be included. To accelerate the use of renewable energies in such buildings, BIPVs should be actively used in windows and on roofs. Window-type BIPVs are being developed in various forms depending on the size, composition, area ratio of the window, specification of glass, and so on. To analyze the applicability of various solar cells as window-type BIPVs, in this study, we evaluated their applicability, at the current development level, by analyzing the indoor illuminance, heat gain and heat loss; the cooling, heating, and lighting energy levels; and the generation performance of the various solar cells. To enhance the future applicability of window type BIPV, we analyze the overall energy performance of the building, according to changes in visible light transmittance and generation efficiency. The main research results are as follows. The area ratios above the standard illuminance, based on the window type and according to the VLT, were in order of low-e glazing, a-Si window, DSSC window, and c-Si window. The heat gain of the semi-transparent solar cell winodw was remarkably low. The energy consumption of buildings was highest in the order of c-Si window, DSSC window, a-Si window, and clear low-e window. However, in the case of including the power generation performance of the solar cell, the energy consumption was found to be high in order of DSSC window, c-Si window, a-Si window, and clear low-e window. In the future, if a window-type BIPV is developed, we believe that improvement in power generation performance and improvement in visible light transmittance will be needed.

• Journal of Surface Science and Engineering
• /
• v.55 no.2
• /
• pp.91-95
• /
• 2022

ZnO single layer (60 nm thick) and ZnO with Ag interlayer (ZnO/Ag/ZnO; ZAZ) films were deposited on the glass substrates by using radio frequency (RF) and direct current (DC) magnetron sputter to evaluate the effectiveness of Ag interlayer on the optical visible transmittance and the conductivity of the films. In the ZAZ films, the thickness of ZnO layers was kept at 30 nm, while the Ag thickness was varied as 5, 10, 15 and 20 nm. In X-ray diffraction (XRD) analysis, ZnO films show the (002) diffraction peak and ZAZ films also show the weak ZnO (002) peak and Ag (111) diffraction peak. As a thickness of Ag interlayer increased to 20 nm, the grain size of the Ag films enlarged to 11.42 nm and the optical band gap also increased from 4.15 to 4.22 eV with carrier concentration increasing from 4.9 to 10.5×10²¹ cm^-3. In figure of merit measurements, the ZAZ films with a 10 nm thick Ag interlayer showed the higher figure of merit of 4.0×10^-3 Ω^-1 than the ZnO single layer and another ZAZ films. From the experimental result, it is assumed that the Ag interlayer enhanced effectively the opto-electrical performance of the ZAZ films.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.10-15
• /
• 2020

Ultraviolet rays, which have wavelengths smaller than 400 nm, are very harmful to the eyes. Recently, high-energy visible light was also revealed to be harmful to retinal cells. Therefore, polymer eyeglass lenses that can block UV and high-energy visible light are needed for eye health. In this study, high-refractive-index polymer eyeglass lens, n=1.67, were manufactured using the injection-mold method with the m-xylene diisocyanate monomer, 2,3-bis((2-mercaptoethyl)thio)-1-propanethiol monomer, benzotriazole UV absorber, release of alkyl phosphoric ester, dye mixture of CI solvent violet 13, and catalyst of dibutyltin dichloride mixture. A multi-layer anti-reflection coating was applied to manufactured polymer eyeglass lenses for both sides using an E-beam evaporation system. The optical properties of the manufactured lenses with the UV and high-energy visible light-blocking function were analyzed by UV-visible spectrophotometry. As a result, the polymer eyeglass lens with a UV absorber of 0.5 wt. % blocked 99% of UV and high-energy visible light shorter than 411 nm. The average transmittance of the polymer eyeglass lens with a UV absorber of 0.5wt.% was 97.9% in the range of 460 ~ 660 nm for photopic eye sensitivity higher than 10%. Therefore, clear image acquisition in photopic vision is possible.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.4
• /
• pp.145-150
• /
• 2004

We have investigated the structural, electrical and optical properties of Al-doped ZnO (AZO) thin films grown on glass substrate by pulsed DC magnetron sputtering as functions of pulse frequency and substrate temperature. A highly c-axis oriented AZO thin film is grown in perpendicular to the substrate when pulse frequency of 30 kHz and substrate temperature of $400^{\circ}C$ was applied. Under this optimized growth condition, the resistivity of AZO thin films exhibited $7.40\times 10^{-4}\Omega \textrm{cm}$. This indicated that the decrease of film resistivity resulted from the improvement of film crystallinity. The optical transmittance spectra of the films showed a very high transmittance of 85∼90 % in the visible wavelength region and exhibited the absorption edge of about 350 nm. The results show the potential application for transparent conductivity oxide (TCO) thin films.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.4
• /
• pp.596-600
• /
• 2012

ZnO-$SnO_2$ films were deposited by rf magnetron sputtering using a ZnO-$SnO_2$ (2:1 molar ratio) target. The target was made from a mixture of ZnO and $SnO_2$ powders calcined at $800^{\circ}C$. The working pressure was 1 mTorr, and the rf power was 120 W. The ratio of oxygen to argon ($O_2$:Ar) was varied from 0% to 10%, and the substrate temperature was varied from $27^{\circ}C$ to $300^{\circ}C$. The crystallographic properties and the surface morphologies of the films were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force spectroscopy (AFM). The ZnO-$SnO_2$ films deposited in $O_2$:Ar = 10% exhibited resistivity higher than $10^6{\Omega}cm$ and transmittance of more than 80% in the visible range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.984-989
• /
• 2012

We have investigated the structural, electrical and optical properties of Ga-doped ZnO (GZO) thin films prepared by RF magnetron sputtering with laboratory-made ZnO targets containing 1, 3, 5, 7 wt% of $Ga_2O_3$ powder as a doping source. The GZO thin films show the typical crystallographic orientation with c-axis regardless of $Ga_2O_3$ content in the targets. The $3,000{\AA}$ thick GZO thin films with the lowest resistivity of $7{\times}10^{-4}{\Omega}{\cdot}cm$ are obtained by using the GZO ($Ga_2O_3$= 5 wt%) target. Optical transmittance of all films shows higher than 80% at the visible region. The optical energy band gap for GZO films increases as the carrier concentration ($n_e$) in the film increases.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.94.2-94.2
• /
• 2010

Indium tin oxide (ITO) Thin films were grown on Non-alkarai glass Substrates by PVD method and Subsequently Subjected to ($100^{\circ}C-350^{\circ}C$) Thermal Annealing (TA) In Nitr Oxygen ambinent. Most of all, The effect of TA treatment on the structural properties were studied by using X-Ray diffraction and atomic force microscopy, while optical properties were studied by UV-Transmittance measurements. After TA treatment, the XRD spectra have shown an effective relaxation of the residual compressive stress, As a result, XRD peaks increase of the intensity and narrowing of full width at half-maximun (FWHM). In addtion The microstructure, The surface morphology, the optical transmittance changed and improved, and we investigated The effects of temperature, Time and atmosphere during the TA on the structural and electrical properties of the ITO/glass on TA at $300^{\circ}C$. As a results, the films are highly transparent (80%～89%) in visible region. AFM analysis shows that the films are very smooth with root mean square surface roughness 0.58nm -2.75nm thickness film. It is observed that resistivity of the films drcreases T0 $1.05{\times}10^{-4}{\Omega}cmt$ $6.06{\times}10^{-4}{\Omega}cm$, while mobility increases from $152cm^2/vs$ to $275cm^2/vs$.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.3
• /
• pp.109-112
• /
• 2016

We have considered the influence of electron irradiation on the optical and electrical properties of $SnO_2$ thin films deposited with reactive RF magnetron sputtering. After deposition, the films electron irradiated at 300 eV shows a lower sheet resistance of $277{\Omega}/{\square}$ and the optical transmittance in a visible wave length region also influenced with the electron irradiation energy. The film that electron irradiated at 400 eV shows a higher optical transmittance of 82.6% in this study. By comparison of figure of merit, it is concluded that the post-deposition electron irradiation at 300 eV is the optimum condition for the enhancement of opto-electrcal performance of $SnO_2$ thin film in this study.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.401-405
• /
• 2017

Because silicon thin film solar cells have a high absorption coefficient in visible light, they can absorb 90% of the solar spectrum in a $1-{\mu}m$-thick layer. Silicon thin film solar cells also have high transparency and are lightweight. Therefore, they can be used for building integrated photovoltaic (BIPV) systems. However, the contact electrode needs to be replaced for fabricating silicon thin film solar cells in BIPV systems, because most of the silicon thin film solar cells use metal electrodes that have a high reflectivity and low transmittance. In this study, we replace the conventional aluminum top electrode with a transparent aluminum-doped zinc oxide (AZO) electrode, the band level of which matches well with that of the intrinsic layer of the silicon thin film solar cell and has high transmittance. We show that the AZO effectively replaces the top metal electrode and the bottom fluorine-doped tin oxide (FTO) substrate without a noticeable degradation of the photovoltaic characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.387.1-387.1
• /
• 2016

Transparent materials are necessary for most photoelectric devices, which allow the light generation from electric energy or vice versa. Metal oxides are usual materials for transparent conductors to have high optical transmittance with good electrical properties. Functional designs may apply in various applications, including solar cells, photodetectors, and transparent heaters. Nanoscale structures are effective to drive the incident light into light-absorbing semiconductor layer to improve solar cell performances. Recently, the new metal oxide materials have inaugurated functional device applications. Nickel oxide (NiO) is the strong p-type metal oxide and has been applied for all transparent metal oxide photodetector by combining with n-type ZnO. The abrupt p-NiO/n-ZnO heterojunction device has a high transmittance of 90% for visible light but absorbs almost entire UV wavelength light to show the record fastest photoresponse time of 24 ms. For other applications, NiO has been applied for solar cells and transparent heaters to induce the enhanced performances due to its optical and electrical benefits. We discuss the high possibility of metal oxides for current and future transparent electronic applications.