• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.202-208
• /
• 2017

최근 개발된 선박용 주기관은 추진효율 향상과 연료소비율 저감기술이 요구됨에 따라 과거에 비해 높은 비틀림진동 기진력 특성을 갖고 있다. 따라서 이를 제어하기 위해 기본적으로 엔진 선단에 점성 댐퍼나 점성-스프링댐퍼를 장착한다. 점성댐퍼의 경우 댐퍼 내부에 채워진 실리콘 오일이 탄성적인 연결이 없다고 가정하고 댐퍼설계를 하여 왔으나 고점도 실리콘 오일은 높은 점도에 따른 비틀림 강성이 존재할 뿐만 아니라 작동온도와 주파수에 따라 비선형적인 동특성을 갖는다. 본 논문에서는 고점도 실리콘 오일이 적용된 점성댐퍼의 동특성을 확인하고 해당 댐퍼가 장착된 축계의 비틀림진동 특성을 검토하였다. 이를 위해 점성댐퍼의 최적 동특성을 이론적으로 해석하는 방법을 검토하였고, 고점도 실리콘 오일로 채워진 점성댐퍼로 해당축계의 비틀림진동 제어를 하는 경우 댐퍼 작동온도 및 경년변화를 고려한 추진축계 최적 설계 방안에 대해서 검토하였다.

• Smart Structures and Systems
• /
• 제24권3호
• /
• pp.345-360
• /
• 2019

The shear keys are set in a seismic isolation system to resist the long-term service loadings, and are cut off to isolate the earthquakes. This paper investigated the influence of shear keys on the seismic performance of a vertical spring-viscous damper-concave Coulomb friction isolation system by an incremental dynamic analysis (IDA) and a performance-based assessment. Results show that the cutting off process of shear keys should be simulated in a numerical analysis to accurately predict the seismic responses of isolation system. Ignoring the cutting off process of shear keys usually leads to untrue seismic responses in a numerical analysis, and many of them are unsafe for the design of isolated structure. And those errors will be increased by increasing the cutting off force of shear keys and decreasing the spring constant of shear keys, especially under a feeble earthquake. The viscous damping action postpones the cutting off time of shear keys during earthquakes, and reduces the seismic isolation efficiency. However, this point can be improved by increasing the spring constant of shear keys.

• Smart Structures and Systems
• /
• 제15권3호
• /
• pp.627-643
• /
• 2015

Negative stiffness, previously emulated by active or semi-active control for cable vibration mitigation, is realized passively using a self-contained highly compressed spring, the negative stiffness device (NSD).The NSD installed in parallel with a viscous damper (VD) in the vicinity of cable anchorage, enables increment of damper deformation during cable vibrations and hence increases the attainable cable damping. Considering the small cable displacement at the damper location, even with the weakening device, the force provided by the NSD-VD assembly is approximately linear. Complex frequency analysis has thus been conducted to evaluate the damping effect of the assembly on the cable; the displacement-dependent negative stiffness is further accounted by numerical analysis, validating the accuracy of the linear approximation for practical ranges of cable and NSD configurations. The NSD is confirmed to be a practical and cost-effective solution to improve the modal damping of a cable provided by an external damper, especially for super-long cables where the damper location is particularly limited. Moreover, mathematically, a linear negative stiffness and viscous damping assembly has proven capability to represent active or semi-active control for simplified cable vibration analysis as reported in the literature, while in these studies only the assembly located near cable anchorage has been addressed. It is of considerable interest to understand the general characteristics of a cable with the assembly relieving the location restriction, since it is quite practical to have an active controller installed at arbitrary location along the cable span such as by hanging an active tuned mass damper. In this paper the cable frequency variations and damping evolutions with respect to the arbitrary assembly location are then evaluated and compared to those of a taut cable with a viscous damper at arbitrary location, and novel frequency shifts are observed. The characterized complex frequencies presented in this paper can be used for preliminary damping effect evaluation of an adaptive passive or semi-active or active device for cable vibration control.

• Earthquakes and Structures
• /
• 제13권6호
• /
• pp.551-559
• /
• 2017

A large number of isolation systems are designed without considering the non-uniform friction distribution in space. In order to analyze the effects of non-uniform friction distribution on the structural response of isolation system, this paper presented a simplified rolling-damper-spring isolation system and analyzed the structural responses under earthquakes. The numerical results indicate that the calculation errors related to the peak values of structural acceleration, relative displacement and residual displacement are sequentially growing because of the ignorance of non-uniform friction distribution. However, the influence rule may be weakened by the spring and damper actions, and the unreasonable spring constant may lead to the sympathetic vibration of isolation system. In the case when the friction variability is large and the damper action is little, the non-uniform friction distribution should be taken into consideration during the calculation process of the peak values of structural acceleration and relative displacement. The non-uniform friction distribution should be taken into full consideration regardless of friction variability degree in calculating the residual displacement of isolation system.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권6호
• /
• pp.70-78
• /
• 2023

보통중심가새골조는 단순한 설계절차를 갖는 이점이 있다. 이와 같은 이유로, 지진하중에 대한 내진성능이 다른 골조 시스템에 비해 크게 효과적이지 않음에도 불구하고 중간 또는 낮은 수준의 지진을 받는 소규모 골조 구조물에 널리 사용되어 왔다. 횡방향 지진 하에서 압축 거동에 대해 취약한 가새부재를 갖는 보통중심가새골조의 내진성능을 향상시키기 위해, 통상적으로 점성감쇠기에 의한 내진보강이 도입되어 왔다. 하지만, 점성감쇠기 자체는 일반적으로 구조물을 원래 위치로 복원시킬 수 있는 강성을 갖지 않는다. 이는 구조물에 잔류 변위를 유발시킬 수도 있다. 이 논문에서는 휨강성을 갖는 상·하부 보가 비선형-탄성 스프링 역할을 하여 외부 변위 이력을 받는 스프링-감쇠기 시스템을 원래 위치로 복원시키는 자가복원형 점성감쇠기 시스템이 개발되었다. 단순화된 골조 구조물에 대한 수치해석은 개발된 자가복원형 점성감쇠기 시스템을 포함할 경우 지진이 가해지는 동안 에너지 소산을 통해 어떻게 골조 구조물의 향상된 내진성능을 가져오는지 보여준다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.947-951
• /
• 2007

This paper is concerned with a new concept for the damper without neither a coil spring nor fluid. The new damper concept consists of the permanent magnets and the cylinder of the conducting material. The opposite pole magnets produces the repulsive forces and this is substituted for the coil spring. The relative motion between the magnets and conducting cylinder produces eddy currents thus resulting in the electromagnetic force, which turns out to be the damping force thus and is substituted for a damping fluid. This damper is called the eddy current damper(ECD). The important advantage of the proposed ECD is that it does not require the damping fluid and any external power and is non-contacting and relatively insensitive to temperature. In the present study, the proposed ECD was constructed and experiments were performed to investigate its dynamic characteristics. The experiments shows that the proposed ECD has the excellent damping ability.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1404-1408
• /
• 2006

In this paper, a hybrid-type vibration isolator which has air chamber(spring) and viscous damper in series is developed. The developed vibration isolator is designed to perform 3 following functions : spring function for normal operating conditions, damping function to reduce an impact for sudden move of upper beam, and finally leveling function. Based on the given natural frequency and damping factor, the design procedure is proposed. The performance of the developed isolator is tested by measuring stiffness and damping.

• 한국지진공학회논문집
• /
• 제11권3호
• /
• pp.63-72
• /
• 2007

비상디젤발전기는 원전의 안전성에 큰 영향을 미치는 매우 중요한 기기이다. 본 연구에서는 세 종류의 비상디젤발전기를 대상으로 가동중 진동을 계측하여 기초시스템에 따른 가동중 진동의 저감효과를 비교하였다. 대상 원전은 영광 5호기, 울진 2호기 및 울진 3호기 원전의 비상디젤발전기로 하였다. 영광 5호기와 울진 3호기의 비상디젤발전기는 동일한 종류의 비상디젤발전기로서 기초형식만 앵커볼트 고정과 스프링-댐퍼시스템을 이용한 면진으로 구분된다. 울진 2호기 비상디젤발전기는 기초부분에 seismic block을 설치하고 코일스프링을 이용하여 진동저감효과를 고려하였으므로 좋은 비교가 될 것이다. 이러한 진동계측의 목적은 기초형태에 따른 진동저감 효과를 비교해 보기 위함이다. 결과적으로 스프링-댐퍼 시스템이 진동저감과 시스템의 안정적 거동측면에서 좋은 효과를 보이고 있음을 알 수 있었다.

• 드라이브 ㆍ 컨트롤
• /
• 제16권1호
• /
• pp.7-13
• /
• 2019

The objective of this study was to present a damped pneumatic suspension, a bike fork suspension, which can adapt itself to incoming road excitations is presented in this paper. It consists of a hydraulic damper and a pneumatic spring in parallel with a linear spring. The study also proposed a variable and switchable orifice, in the hydraulic damper, to select appropriate damping property. Hydraulic-pneumatic circuit model for the bike fork suspension was established based on AMESim, in order to predict its performance. In addition, elastic-damping characteristics of the fork such as spring constant and viscous damping coefficient were computed and compared, for validation, with those evaluated by experiment using the universal test machine. Through simulation analysis and test, it was established that the hydraulic-pneumatic circuit model is effective and practical for development of future MTB suspensions.

• Smart Structures and Systems
• /
• 제23권6호
• /
• pp.669-682
• /
• 2019

Vibration mitigation of cables or hangers is one of the crucial problems for cable supported bridges. Previous research focused on the behaviors of cable with dampers or crossties, which could help engineering community apply these mitigation devices more efficiently. However, less studies are available for hybrid applied cross-ties and dampers, especially lack of both analytical and experimental verifications. This paper studied damping and frequency of two parallel identical cables with a connection cross-tie and an attached damper. The characteristic equation of system was derived based on transfer matrix method. The complex characteristic equation was numerically solved to find the solutions. Effects of non-dimensional spring stiffness and location on the maximum cable damping, the corresponding optimum damper constant and the corresponding frequency of lower vibration mode were further addressed. System with twin small-scale cables with a cross-link and a viscous damper were tested. The damping and frequency from the test were very close to the analytical ones. The two branches of solutions: in-phase modes and the out-of-phase modes, were identified; and the two branches of solutions were different for damping and frequency behaviors.